Humhold Ceiling Fan Light

Content

• Introduction

• Installation

• Remote Controller Setting

• Cellphone App Setting

• Cleaning and Maintenance

• Technical Specifications

• Product Features

• Safety Precautions

• Troubleshooting

• Technical Support

Introduction

This Humhold ceiling fan light is manufactured with great care and utilizes the latest in technology. Humhold is confident that you will be fully satisfied with its performance and reliability. It provides exact instructions for installation, operation, and maintenance, and also supplies some useful hints.

A diagram shows the ceiling fan light with its main components labeled: Lamp Base, Safety Steel Rope, Fan Blades, and Wind Guide Wheel.

An image shows a remote control labeled 'REMOTE X1' and a set of screw accessories labeled 'SCREW ACCESSORY SET' with quantities indicated (4x, 4x, 1x, 2x, 3x).

Installation

1. Open the package, take out the fan lamp, press down the base, and rotate to remove the base.
2. Take off the safety steel rope.
3. Base installation: Fix the lamp base on the ceiling mounting base with screws, and confirm that the base is firmly installed. If there's no mounting base on the ceiling, use an electric drill to drill installation holes on the ceiling, and put the expansion pipe into the installation hole. A diagram illustrates the base installation process, showing the lamp base being attached to a ceiling mounting base with screws, and an alternative method involving drilling holes and using expansion pipes.
4. Buckle up the safety steel rope. A diagram shows the safety steel rope being buckled up.
5. Wiring: Use wiring caps to connect the L/N/Ground wires. Ensure the power is OFF before wiring. A diagram illustrates the wiring connections using wiring caps for L/N/Ground wires.
6. Hold the edges of both sides of the lamp body with both hands, align with the base, gently push both sides upward and rotate clockwise at the same time. After hearing the "click", then install the safety screw on the side of the lamp body, and make sure the lamp body cannot rotate after installation. The installation is completed. A diagram shows how to align and rotate the lamp body onto the base, and install the safety screw.

Cleaning and Maintenance

1. Remove the safety screw on the side of the lamp body, hold the fan lamp with both hands, push it upward and rotate it counterclockwise to remove the fan lamp body.
2. Remove the wiring caps, disconnect the wires, and remove the safety steel rope.
3. According to the opening sign of the protective net and fan blade, it can be cleaned after opening and taking out.

Note: Do not flush the lamp body with water directly. After the fan lamp is cleaned, please dry it first. To avoid the risk of falling, please confirm the parts are installed correctly.

WARNING Always switch off the power prior to cleaning in the vicinity of electrical parts (lamps, fan blades etc.). Wipe up excess moisture with a sponge or cloth to prevent water or liquid from getting into any electrical part and causing an electric shock. Do not use flammable or toxic cleaning liquids.

A diagram illustrates the removal of the fan lamp body by releasing the safety screw, pushing upward, and rotating counterclockwise. It also shows the disconnection of wires and removal of the safety steel rope.

WIFI Operation Instruction

1.1. Download and install App

Use your phone to scan the QR code below or search "Smart Life" in the application market to download and install the App.

A QR code for downloading the "Smart Life" application.

For the first use, you need to use your mobile phone number or Email address to register and log in.

1.2. Device configuration and control

1. Connect the device to the power supply and confirm that the device can work normally (the light turns on slowly).
2. Continuous ON-OFF-ON-OFF-ON: Power on and off three times (power on for 2~3 seconds, power off for 5~10 seconds) to make the device enter the distribution network mode. At this time, the main light source will remind you to breathe.
3. Open the Smart Life App, click "Add Device" in the upper right corner, and wait for the App to automatically search for peripheral devices. Screenshots of the "Smart Life" mobile application interface, showing steps for adding a device, searching for nearby devices, and confirming successful device addition.
4. After the App scans the device, click "Add" to bind the device.

Remote Control Instructions

2.1. Pair code

Connect the device to the power supply and confirm that the device can work normally (the light turns on slowly).

Turn off the power of the device for 5~10 seconds and then turn on the power again.

Long press Button 1 until the device flashes 3 times quickly, then let go. The code pairing of the remote control is successful. At this time, you can press the button to control the device.

2.2. Clear code

Connect the device to the power supply and confirm that the device can work normally (the light turns on slowly).

Turn off the power of the device for 5~10 seconds and then turn on the power again.

Long press Button 2 until the device flashes 3 times quickly, then let go. The remote control is successfully cleared. At this time, the remote control can no longer control the device and needs to be re-paired before it can be used.

2.3. Control Functions:

• Button 1: All off, short press to turn off the main light & color light & fan.
• Button 2: Fan mode, short press to switch between natural and comfortable wind.
• Button 3: Fan direction, short press to switch between forward and reverse.
• Button 4: Fan rocker switch, only some models support this function.
• Button 5: Fan switch, short press to turn on/off the fan, long press the button for 5 seconds to enable the device to enter the App distribution network mode.
• Button 6: Fan speed, short press to adjust the speed of 6 levels.
• Button 7: White light switch, short press to turn on/off the white light.
• Button 8: Color light switch, short press to turn on/off color light.
• Button 9: Brightness addition and subtraction, short press to adjust the brightness of 10 levels, and long press to adjust the brightness steplessly.
• Button 10: Addition and subtraction of temperature, short press to adjust the 10-level temperature, long press to adjust the temperature steplessly.
• Button 11: Color static cycle switching (red, yellow, green, blue, purple, white).
• Button 12: Color dynamic cycle switching.
• Button 13: 1 hour/4 hours countdown timer off, fan & white light & color light all off at the same time.

A diagram of the remote control with numbered buttons, each corresponding to a specific function described in the text.

Technical Specifications

Product: Modern ceiling fan light

Model: HDFSD-B02

Input: 110V-60Hz

Fan wattage: 15W

Light wattage: 24(2900k)-48W(6500K) (9 6 x 1W/LED module)

Total Wattage: 60W

Light color Range: 2900K-6500K

Supportive system: Android 4.4 or iOS 9.0 and newer versions.

Wireless connection: Wi-Fi IEEE 802.11b/g/n 2.4GHz, Alexa Voice, Google Assistant

Product Features

• Color Adjustment ?️
• Brightness Adjustment ☀️
• Night Mode ?
• Cellphone App Control ?
• Timing Function ⏱️
• Fan Speed Setting ?
• Reversible ?
• Easy Install ✅

Safety Precautions

1. Please confirm whether the voltage meets the working voltage of the product before use. Using inappropriate voltage may damage the product and cause potential safety hazards.
2. The light source of this lamp is a non user replacement light source, and the light source in this lamp shall be replaced by the manufacturer or its service agent or a person with similar qualification.
3. During the operation of the fan, do not touch the fan blade to avoid danger.
4. The installation height of fan lamp shall be more than 2.3m above the ground.
5. The lamp can be controlled by the remote controller and mobile phone software. After the lamp is turned off by the remote controller or mobile phone software, it does not mean that the power supply is actually cut off. In this case, it is forbidden to touch, replace or disassemble the lamp, otherwise it may cause electric shock and even casualties.

Before installation, be sure to cut off the power supply to prevent electric shock. During installation, the operation shall be carried out in strict accordance with the instructions. If the installation is improper, it is easy to cause accidents such as fire, electric shock or lamp body falling.

Please entrust electrical professionals to install or repair. The wiring shall comply with electrical standards or national standards to avoid danger.

Warning: Electrical Hazard ⚡

Warning: Professional Installation Recommended ⚠️

Troubleshooting

Technical Support

For technical support issues please visit Amazon order page, our online technical support team members will answer your questions.

Contact Information

Humhold CEILING FAN

We want to hear your voice! Feel free to touch base if you encounter any issue when using our product(s) or want to know more about our brand. Humhold will be more than happy to provide top-notch pre-sales & after-sales service 24/7.

Email: support@humhold.com