Owner's Manual for MEAN WELL models including: LPF-90-15, LPF-90-20, LPF-90-24, LPF-90-30, LPF-90-36, LPF-90-36 Constant Voltage Plus Constant Current LED Driver, LPF-90-36, Constant Voltage Plus Constant Current LED Driver, Plus Constant Current LED Driver, Current LED Driver, LED Driver
File Info : application/pdf, 6 Pages, 540.19KB
DocumentDocument90W Constant Voltage + Constant Current LED Driver
LPF-90 series
User's Manual
IP67
File Name:LPF-90-SPEC 2024-02-19
90W Constant Voltage + Constant Current LED Driver
LPF-90 series
SPECIFICATION
MODEL
LPF-90-15 LPF-90-20 LPF-90-24 LPF-90-30 LPF-90-36
OUTPUT
DC VOLTAGE
15V
20V
24V
30V
CONSTANT CURRENT REGION Note.2 9 ~ 15V
12 ~ 20V
14.4 ~ 24V 18 ~ 30V
RATED CURRENT
5A
4.5A
3.75A
3A
RATED POWER
Note.5 75W
90W
90W
90W
RIPPLE & NOISE (max.) Note.3 150mVp-p 150mVp-p 150mVp-p 200mVp-p
VOLTAGE TOLERANCE Note.4 ±4.0%
±4.0%
±4.0%
±4.0%
LINE REGULATION
±0.5%
±0.5%
±0.5%
±0.5%
LOAD REGULATION
±1.5%
±1.0%
±0.5%
±0.5%
SETUP, RISE TIME Note.6 1200ms, 200ms / 115VAC 500ms, 200ms / 230VAC
HOLD UP TIME (Typ.)
16ms/230VAC 16ms/115VAC
36V 21.6 ~ 36V 2.5A 90W 200mVp-p ±4.0% ±0.5% ±0.5%
VOLTAGE RANGE
90 ~ 305VAC 127 ~ 431VDC Note.5 (Please refer to "STATIC CHARACTERISTIC" section)
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR
PF0.97/115VAC, PF0.96/230VAC, PF0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
LPF-90-42
42V 25.2 ~ 42V 2.15A 90.3W 200mVp-p ±4.0% ±0.5% ±0.5%
LPF-90-48
48V 28.8 ~ 48V 1.88A 90.24W 200mVp-p ±4.0% ±0.5% ±0.5%
LPF-90-54
54V 32.4 ~ 54V 1.67A 90.18W 200mVp-p ±4.0% ±0.5% ±0.5%
TOTAL HARMONIC DISTORTION
THD< 20%(@load60%/115VC,230VAC; @load75%/277VAC) (Please refer to "TOTAL HARMONIC DISTORTION(THD)" section)
INPUT
EFFICIENCY (Typ.)
89%
90%
90.5%
91%
91%
91%
91%
91%
AC CURRENT INRUSH CURRENT(Typ.)
0.95A / 115VAC 0.5A / 230VAC 0.4A / 277VAC COLD START 70A(twidth=435s measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER
4 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.75mA / 240VAC
OVER CURRENT PROTECTION
OVER VOLTAGE
95 ~ 108%
Constant current limiting, recovers automatically after fault condition is removed
18 ~ 21V
23 ~ 27V
28 ~ 34V
34 ~ 38V
41 ~ 46V
Shut down o/p voltage, re-power on to recover
47 ~ 53V
54 ~ 60V
59 ~ 65V
OVER TEMPERATURE
Shut down o/p voltage, re-power on to recover
WORKING TEMP.
Tcase=-40 ~ +70 (Please refer to " OUTPUT LOAD vs TEMPERATURE" section)
MAX. CASE TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY
Tcase=+70 20 ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/ (0 ~ 50)
VIBRATION
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY STANDARDS Note.8
UL8750(type"HL"), CSA C22.2 No.250.13-12, ENEC BS EN/EN61347-1, BS EN/EN61347-2-13 independent, BS EN/EN62384, J61347-1, J61347-2-13, EAC TP TC 004, GB19510.1,GB19510.14,IP67 approved ; Design refer to UL60950-1
SAFETY & WITHSTAND VOLTAGE
EMC
ISOLATION RESISTANCE
EMC EMISSION Note.8
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25/ 70% RH
Compliance to BS EN/EN55015,BS EN/EN61000-3-2 Class C (@load60%) ; BS EN/EN61000-3-3, GB/T 17743 , GB17625.1,EAC TP TC 020
EMC IMMUNITY MTBF
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level (surge immunity Line-Line 2KV),EAC TP TC 020 3292.9K hrs min. Telcordia SR-332 (Bellcore) ; 301.7Khrs min. MIL-HDBK-217F (25)
OTHERS NOTE
DIMENSION
161*61*36mm (L*W*H)
PACKING
0.7Kg;20pcs/15Kg/0.73CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature.
2. Please refer to "DRIVING METHODS OF LED MODULE".
3. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
4. Tolerance : includes set up tolerance, line regulation and load regulation.
5. De-rating may be needed under low input voltages. Please refer to "STATIC CHARACTERISTIC" sections for details.
6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.
7. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
(as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 8.To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch
withoutpermanentlyconnectedtothemains 9. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 70 or less.
10. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com 11. The ambient temperature derating of 3.5/1000m with fanless models and of 5/1000m with fan models for operating altitude higher than 2000m(6500ft).
10. For any application note and IP water proof function installation caution, please refer our user manual before using.
https://www.meanwell.com/Upload/PDF/LED_EN.pdf
Product Liability DisclaimerFor detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:LPF-90-SPEC 2024-02-19
90W Constant Voltage + Constant Current LED Driver
BLOCK DIAGRAM
LPF-90 series
fosc : 100KHz
EMI FILTER
I/P
&
RECTIFIERS
PFC CIRCUIT
POWER
RECTIFIERS
+V
SWITCHING
& FILTER
-V
O.L.P.
O.T.P.
O.L.P.
PWM & PFC CONTROL
DETECTION CIRCUIT
O.V.P.
DRIVING METHODS OF LED MODULE
This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs.
100
Vo(%)
60 (min.)
(A) Constant
Voltage area
(B) Constant Current area
(C) Hiccup Protection
50
100
Io(%)
Typical output current normalized by rated current (%)
In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL.
File Name:LPF-90-SPEC 2024-02-19
90W Constant Voltage + Constant Current LED Driver
OUTPUT LOAD vs TEMPERATURE
LPF-90 series
LOAD (%)
THD LOAD (%)
100
80 230VAC Input only
60
40
20
-40
-25 -10 0
15
30
50
60
70 (HORIZONTAL)
AMBIENT TEMPERATURE,Ta ()
LOAD (%)
100
80 230VAC Input only
60
40
20
-40
-25 -10 0
15
30
50
60
70 (HORIZONTAL)
Tcase ()
STATIC CHARACTERISTIC
100 90 80 70 60 50 40
90 100 125 135 145 155 165 175 180 200 230 305
INPUT VOLTAGE (V) 60Hz De-rating is needed under low input voltage.
TOTAL HARMONIC DISTORTION (THD)
48V Model, Tcase at 60
25
20
15 115VAC
10 230VAC
5
277VAC
0
50%
60%
70%
80%
90% 100%
LOAD
EFFICIENCY(%)
PF
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 60 Constant Current Mode
1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1
0
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
(90W)
115VAC 230VAC 277VAC
LOAD
EFFICIENCY vs LOAD
LPF-90 series possess superior working efficiency that up to 91% can be reached in field applications. 48V Model, Tcase at 60
93
92
91
90
89
277VAC
230VAC
88 115VAC
87
86
85 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD
File Name:LPF-90-SPEC 2024-02-19
90W Constant Voltage + Constant Current LED Driver
LIFETIME
LPF-90 series
LIFETIME(Kh)
120
100
80
60
40
20
0
20
30
40
50
60
70
Tcase( )
File Name:LPF-90-SPEC 2024-02-19
90W Constant Voltage + Constant Current LED Driver
MECHANICAL SPECIFICATION
LPF-90 series
CASE NO.: LPF-90A Unit:mm
AC/L(Brown) AC/N(Blue)
300±20 SJOW 17AWG×2C & H05RN-F 2×1.0mm2
161
4.5
tc
91
4
tc : Max. Case Temperature
4 4.5
300±20 SJOW 17AWG×2C & 05RN-F 2×1.0mm2
+V(Red) -V(Black)
4 61
9 4
36
Recommend Mounting Direction
INSTALLATION MANUAL
Please refer to:http://www.meanwell.com/manual.html
File Name:LPF-90-SPEC 2024-02-19
MEAN WELL Switching Power Supply Manufacturer