Installation Guide for AcuityBrands models including: 2024 LED Strip Light Linear LED Strip Light, 2024, LED Strip Light Linear LED Strip Light, Light Linear LED Strip Light, Linear LED Strip Light, LED Strip Light, Strip Light, Light
CLX LED Strip Light - CLX Linear LED Strip Light
File Info : application/pdf, 15 Pages, 1.53MB
DocumentDocumentLED IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION · To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels. · Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions. · Installation and service of luminaires should be performed by a qualified licensed electrician. · Maintenance of the luminaires should be performed by person(s) familiar with the luminaires' construction and operation and any hazards involved. Regular fixture maintenance programs are recommended. · It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary. · DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced. · Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov. · These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser's or owner's purposes, this matter should be referred to Acuity Brands Lighting, Inc. WARNING RISK OF ELECTRIC SHOCK Disconnect or turn off power before installation or servicing. Verify that supply voltage is correct by comparing it with the luminaire label information. Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements. All wiring connections should be capped with UL approved recognized wire connectors. CAUTION RISK OF INJURY Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance. Avoid direct eye exposure to the light source while it is on. WARNING RISK OF BURN Allow lamp/fixture to cool before handling. Do not touch enclosure or light source. Do not exceed maximum wattage marked on luminaire label. Follow all manufacturer's warnings, recommendations and restrictions for: driver type, burning position, mounting locations/methods, replacement and recycling. CAUTION RISK OF FIRE Keep combustible and other materials that can burn, away from lamp/lens. Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying. U351 Rev. U 07/25/2024 Page 1 of 15 LED IMPORTANT SAFETY INSTRUCTIONS CAUTION: RISK OF PRODUCT DAMAGE LEDs are sensitive components and necessary PCBA/LED handling measures are required to provide protection from ESD (Electrostatic Discharge), static electricity, transient voltages, and surge current. If this excess voltage condition occurs it may cause the LED to be damaged leading to non-illumination and/or operational failure. Measures to prevent such damage are effective use of ESD wrist band, ESD foot ware, anti-electrostatic glove, grounded workstations/equipment/tool. Never connect components under load. Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation. Controls for dimming, auto-sensing, or remote control of a luminaire that are not factory-wired to the luminaire must be checked for compatibility with the luminaire prior to installation. LED fixtures must be powered directly off a switched circuit. Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for some volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or conduction cooling. Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambient temperature. Only use fixture in its intended location. LED products are Polarity Sensitive. Ensure proper Polarity before installation. Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit. LEDs are sensitive components and necessary PCBA/LED handling measures are required to provide protection from ESD (Electrostatic Discharge), static electricity, transient voltages, and surge current. If this excess voltage condition occurs it may cause the LED to be damaged leading to non-illumination and/or operational failure. Measures to prevent such damage are effective use of ESD wrist band, ESD foot ware, anti-electrostatic glove, grounded workstations/equipment/tool. Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance. Some components inside the fixture may not be serviceable. In the unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative for assistance. Always read the fixtures complete installation instructions prior to installation for any additional fixture specific warnings. Always ensure that the electrical distribution system is up to NEC (and any applicable local code) requirements. Verify that power distribution system has proper grounding. Lack of proper earth ground can lead to fixture failure and may void warranty. Choose either Part 15 OR Part 18 and move to Page 3 Installation Instructions under Delivery. Lithonia Outdoor will always use Part 15. All luminaires that contain electronic devices that generate frequencies above 9kHz from any component within the luminaire comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation This device complies with Part 18 of the FCC Rules but may cause interference with cordless and cell phones, radios, televisions, and other electronic devices. To correct the problem, move the device away from the luminaire or plug into a different outlet. This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communications equipment operating between 0.45-30MHz. Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com. Our Brands Indoor/Outdoor Lithonia Lighting Carandini Indoor Lighting Gotham Mark Architectural Lighting U351 Rev. U 07/25/2024 Outdoor Lighting American Electric Lighting Antique Street Lamps Controls DARK TO LIGHT LC&D Daylighting SunOptics Page 2 of 15 LED IMPORTANT SAFETY INSTRUCTIONS Holophane RELOC Light Concepts Peerless Renaissance Lighting Winona Lighting Hydrel Tersen ROAM Sensor Switch Synergy Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or handling of its products. ABL LED General Warnings, Form No. 503.203 © 2010, 2016 Acuity Brands Lighting, Inc. All rights reserved. 12/01/10 CLX LED STRIP/LOW BAY INSTALLATION INSTRUCTIONS WARNING: Please read all "important safety instructions" prior to installation of this product. *Luminaire is suitable for closet storage space UL1598 Section 13.6. Available only with nomenclature: CLX L24 1500LM SEF FDL MVOLT GZ10 40K 80CRI A) Identification of CLX Luminaire Page 4 - 5 1) CLX L24 1500LM, 2000LM, 2500LM, 3500LM, 4500LM, 5000LM 2) CLX L36 2250LM, 3000LM, 3750LM, 5250LM, 6750LM, 7500LM 3) CLX L48 3000LM, 4000LM, 5000LM, 7000LM, 9000LM, 10000LM 4) CLX L96 6000LM, 8000LM, 10000LM, 14000LM, 18000LM, 20000LM 5) Lens (FDL, RDL, WDL) Options 6) Sensor Option 7) E10WLCP PS1055 Option 8) ZAC/HC36 V-HANGER Accessory 9) THCLX (Surface Mount) Accessory 10) CLXANGBKT Accessory B) Required Handling Locations Page 5 C) Pre-installation for all mounting Page 5 D) Installation Suspended Fixture Page 6 - 7 E) Installation THCLX (Surface) Mount Page 8 F) Wiring Emergency (BGTD, PS1050) Page 9 G) Commissioning nLight AIR (NLTAIR2 RES7, NLTAIR2 RES7PDT, NLTAIR2 RIO) Page 9 H) Servicing Lens Attachment/Removal, LED Channel Removal - Page 10 - 12 I) Accessory installations Page 13 - 15 1) Narrow Reflector 2) Wide Reflector 3) Wire guard U351 Rev. U 07/25/2024 Page 3 of 15 4) Louver 5) Angle Bracket 6) LUGR Reflector SECTION A: Identification of CLX Luminaire CLX Length Options LED IMPORTANT SAFETY INSTRUCTIONS CLX Lens Options U351 Rev. U 07/25/2024 Page 4 of 15 LED IMPORTANT SAFETY INSTRUCTIONS PS1050 OPTION Sensor OPTION Test switch located on the side of the fixture ZAC/HC36 V-HANGER ACCESSORY THCLX HANGER Sensor option location *Sensor option adds 2" to overall fixture length CLXANGBKT SECTION B: HANDLING PRECAUTIONS ACYRLIC LENS SHEET METAL HOUSING PLASTIC LENS CAPS PLASTIC HOUSING END CAPS When handling the fixture during unpacking and installation take precautions of the plastic Lens and plastic end caps. Dropping the fixture or excess force on the end caps or lens can cause damage. Section C: PRE-INSTALLATION FOR ALL MOUNTING 1. Ensure power is OFF. 2. Inspect the mounting location for damage before installing new CLX Luminaire. Ensure mounting structure is properly sized to support the fixture. 3. Remove luminaire from packing and inspect for any damages. If the fixture is damaged do not use; call your local representative for assistance. 4. WARNING! Removing the lens and opening the fixture during installation exposes the LED's and puts them at risk for damage. Damage to the LEDs caused during installation will not be covered under the warranty. U351 Rev. U 07/25/2024 Page 5 of 15 LED IMPORTANT SAFETY INSTRUCTIONS SECTION D: INSTALLATION - SUSPENDED FIXTURE For V-hanger 1) Feed V-hanger into holes on the Driver channel. 2) Ensure supply wire is not active. If using a continuous row mount skip to steps 5-9. 3) Remove access plate screw as shown below. Input wires will be attached to the access plate. Remove the necessary knockout(s) and connect input wires black to black, white to white and green to green. Use only UL listed connectors rated 75C or greater. Purple and Gray wires are low voltage dimming leads. If ordering with OUTEND option ensure end cap hole and wires are enclosed with a UL approved barrier (cordset, conduit, etc). 4) Push wires into Driver channel and reattach the access plate. V-Hanger V-Hanger Holes Access Plate Screw Housing End Cap Screw For Aircraft Cable 1) Attach bracket to ceiling. Feed aircraft cable through the small threaded pipe. Insert threaded rod into small threaded pipe. Place canopy over bracket and screw the threaded pipe/rod assembly into bracket holding the canopy in place. 2)Open fixture by removing LED Channel and attach large threaded assembly to fixture through 0.3" dia hole using nut provided. Close fixture and feed aircraft cable through large threaded assembly. Requires two per fixture, see following images. Refer to Section H: Servicing on Page 10 for detailed opening instructions. 3) Ensure supply wire is not active. If using a continuous row mount skip to steps 5-9. 4) Remove access plate screw as shown below. Input wires will be attached to the access plate. Remove the necessary knockout(s) and connect input wires black to black, white to white and green to green. Use only UL listed connectors rated 75C or greater. Purple and Gray wires are low voltage dimming leads. If ordering with OUTEND option ensure end cap hole and wires are enclosed with a UL approved barrier (cordset, conduit, etc). 5) Push wires into Driver channel and reattach the access plate. U351 Rev. U 07/25/2024 Page 6 of 15 LED IMPORTANT SAFETY INSTRUCTIONS Aircraft cable Threaded assembly For Continuous Row 5) For STD configurations, Remove Housing End Cap(s) with one screw and disengage end cap snap features. For L/EP option, fixture shipped without endcaps for ease of continuous row mounting. WARNING - Fixtures at end of row must have Housing End Caps installed, as shown below. Housing End Caps can be ordered using nomenclature CLXEPxx xxxx. Failure to install Housing End Caps is a safety hazard. 6) If supplied with a PLR (continuous row wiring), pull PLR connector from fixture. Male will be located on the access plate side. 7) Attach Continuous row mounting bracket into fixture A (supplied with fixture) by snapping into the driver channel and attaching two screws provided in hardware bag. 8) If using a PLR continuous row wiring system, connect female PLR plug from fixture B into the Male PLR plug from fixture A. 9) Snap fixture B into the continuous row bracket and attach using the remaining two screws from the hardware bag. Step 5 Without Sensor Continuous Row Step 7 Step 9 Included in Box Sensor Version Continuous row Use caution to not damage sensor lens U351 Rev. U 07/25/2024 Page 7 of 15 LED IMPORTANT SAFETY INSTRUCTIONS SECTION E: INSTALLATION CLX HANGER MOUNT (THCLX) 1) Attach CLX brackets to structure. If mounting to a T-Grid snap Mounting bracket into T-Grid as shown below. Two CLX brackets MUST be used for standalone fixtures. If mounting in a continuous row one bracket per fixture with one additional bracket per row must be used at a minimum. Two brackets per fixture is highly recommended. 2) Snap Fixture into the THCLX mounting bracket. Ensure fixture is fully engaged into the THCLX bracket, as shown below. 3) Follow steps 2-9 from the suspended mount instructions 4) Tighten THUN brackets around center channel as shown below. Tighten bolts to 13 in/lbs. T-grid DO NOT REMOVE OR TIGHTEN BOLT BEFORE INSTALLING FIXTURE THCLX Rotate THCLX bracket to lock onto T-Grid Installing THCLX to T-GRID Installing THCLX to fixture U351 Rev. U 07/25/2024 THCLX Ensure mounting bracket is fully engaged with the driver channel DRIVER CHANNEL USE CAUTION WHEN WORKING NEAR EXPOSED LEDS Damage to LEDS during installation will not be covered under warranty Page 8 of 15 LED IMPORTANT SAFETY INSTRUCTIONS Section F: Wiring Emergency (BGTD, PS1055, E10WLCP, E10WSTAR) 1) Install fixture with mounting brackets, directly to surface, or with V-hooks. Do not wire. 2) The emergency battery pack indicator light needs to be plugged in during installaion. Remove housing end cap near access plate as shown in previous instructions. 3) For the emergency battery pack the fixture will be provided with a wiring harness at the access plate end. Attach the two connectors together to activate the battery pack 4) Connect unswitching power to unswitched fixture wire. Connect switched power to white, black, and green wires. Supply wire must meet applicable electrical codes and be rated for a minimum of 90C. Purple and gray leads are 0-10V (low voltage) dimming leads. Worst case maximum mounting height CLX FDL WD 30K 90CRI 21 T 5) (OPTION E10WSTAR) STAR (SELF-TESTING AUTOMATED REPORT) WIRELESS a. Please see STAR Self-Testing Automated Reporting for commissioning and additional information. b. LED Status Codes. Flashing Amber Green Off Battery is charging Battery is fully charged Emergency mode Flashing Green Unit is performing a test Flashing Red (once per 0.5 sec.) Electronics failure Flashing Red (once per 6 sec.) Battery failure Two Red Flashes Load failure c. Button Sequences to initiate manual test. Press and Hold Quick Test 2 X Press and Release 60-Second Test 3 X Press and Release 90-Minute Test 1 X Press and Release 4 X Press and Release Cancel 90-Minute Test Load Calibration SECTION G: nLight AIR Commissioning (NLTAIR2 RES7, NLTAIR2 RES7PDT, NLTAIR2 RIO) Out of the Box Sensors perform as follows: 100% Light Output for 7.5 minutes, then 1% light output for 2.5minutes before turning off. 1) Please refer to nLight AIR Quick Start Guide (912-00058-001) included with the luminaire. 2) Please locate additional references and resources below: http://www.acuitybrands.com/clx http://www.acuitybrands.com/nlightair U351 Rev. U 07/25/2024 Page 9 of 15 LED IMPORTANT SAFETY INSTRUCTIONS SECTION H: SERVICING NOTE: 1) Clean fixture as needed. Double check all mounting hardware. 2) After installation, wear protective gloves if the lenses need to be removed 3) The lens snaps into the LED channel. To remove lens, carefully squeeze lens together to disengage from LED channel. 4) To replace the lens snap into LED Channel as shown in the image below. LED CHANNEL Lens Squeeze together to disengage Lens from LED Channel FDL/RDL detachment USE CAUTION WHEN WORKING NEAR EXPOSED LEDS Damage to LEDS during installation will not be covered under warranty WDL DETACHMENT/REATTACHMENT PRESS AGAINST LENS WALL TO DISENGAGE PRESS TOWARD THE FIXTURE WHILE PRESSING AGAINST THE SIDE WALL TO REENGAGE. U351 Rev. U 07/25/2024 Page 10 of 15 LED IMPORTANT SAFETY INSTRUCTIONS NOTE: Cleaning: The LED PCBA should not be exposed or cleaned with any type of fluid such as water, oil, organic solvent, etc other than IPA (Isopropyl Alcohol). Some solvent-based cleaning agents may damage and/or impact the operation and lifetime of the PCBA or LED. Handling and Packaging of Removed PCBA for Return: All PCBAs removed from luminaires during a repair process, which are intended to be returned to Acuity, must be handled with extreme care to ensure no handling or shipping damage occurs. If the PCBAs are to be returned for review they must be repackaged and returned in the same shipping methods as the new replacement PCBAs arrived. 5) If replacing PCBA, ensure power to the fixture is off. 6) If fixture has lens, remove per SECTION H: SERVICING steps 3 & 4. 7) Tag leads before disconnecting from PCBA 8) Disconnect all leads to Old PCBA by pressing down on tab Push down on tab to release Typical Connector: 9) Unscrew fasteners holding the PCBA (L24: ~8 screws, L36: ~12 screws, L48: ~10 screws L96: ~20 screws) REMOVE ALL SCREWS HOLDING PCBA 10) Replace Old PCBA with New PCBA. Note: be mindful of orientation of PCBA to ensure PCBA is centered on LED Channel U351 Rev. U 07/25/2024 Page 11 of 15 LED IMPORTANT SAFETY INSTRUCTIONS 11) Torque down all fasteners to 11 ± 1 IN-LB to secure PCBA to LED Channel 12) Connect all leads to corresponding terminals. Note: Ensuring that positive lead terminate to positive terminal, and negative lead to negative terminal. 13) If installing lens, please refer to steps 3 & 4 of SECTION H: SERVICING. 14) To access electrical components, remove the six screws shown below. USE CAUTION WHEN WORKING NEAR EXPOSED LEDS Damage to LEDS during installation will not be covered under warranty 15) LED Channel MUST hang from driver channel during servicing as shown below. 16) If replacing drivers, ensure power to the fixture is off 17) Tag leads before disconnecting 18) Disconnect all leads from old driver. 19) Unscrew driver using two screws. Attach new driver to channel using two screws. 20) Connect leads to corresponding driver ports 21) Close LED channel and secure using six screws. U351 Rev. U 07/25/2024 Page 12 of 15 LED IMPORTANT SAFETY INSTRUCTIONS SECTION I: ACCESSORIES Wire guard (WGCLX)/Louver (SBL) 1) Install accessory brackets to the top of the fixture with two screws provided. 2) Install Louver or Wire guard to Accessory bracket using four screws provided. Angle Bracket (CLXANGBKT) 1) Attach fixture to angle mounting bracket using screws provided 2) Attach Angle brackets to ceiling (hardware not provided) 3) Choose desired angle (0, 15, 30, or 45 degrees) and fix mounting bracket into angle position using two screws provided CLXANGBKT Screws provided U351 Rev. U 07/25/2024 Page 13 of 15 LED IMPORTANT SAFETY INSTRUCTIONS LUGR REFLECTOR (CLXLUGR) 1. Insert tabs which are on both sides of the Reflector into the respective slots in the Channel in such a way that mounting holes in the Reflector are in line with the holes in the Channel. 2. Install screws on either side, so that Reflector is firmly assembled to the Channel. Tighten to 11in-lbs. 3. Install screws on either side, so that Reflector is firmly assembled to the Channel. 4. Follow and to install another Reflector on other side of the Channel. 5. If installing on an 8ft fixture, repeat process to for each of the remaining 2 Reflectors (8FT Fixture uses 4 x 4FT Reflectors). U351 Rev. U 07/25/2024 Page 14 of 15 LED IMPORTANT SAFETY INSTRUCTIONS Warranty terms are located at the link below: http://www.acuitybrands.com/resources/terms-and-conditions Importado por: Holophane, S.A. de C.V. Av, La Silla #7711 Parque Industrial La Silla Guadalupe, N.L. C.P. 67193 Tel: 52-81-8318-0460 LUMINARIOS Marca: Lithonia Lighting Modelo: CLX PRECAUCION: Por su seguridad y el funcionamiento adecuado del luminario, lea cuidadosamente las siguientes instrucciones antes de empezar la instalación. Este instructivo aplica a todos los luminarios de Lithonia Lighting para uso interior y/o exterior. El número de catálogo especifico, y sus características eléctricas, se encuentran en la etiqueta del producto. 1. Desconecte la alimentación eléctrica de la caja de fusibles antes de instalar el luminario. 2. Abra el luminario para tener acceso a los cables de conexión. 3. Monte el luminario en la ubicación deseada, y asegúrela utilizando dispositivos mecánicos adecuados. 4. Utilizando capuchones aislantes, conecte los cables del luminario. Si el luminario tiene un cable blanco y uno negro, conecte el blanco al neutro del circuito de alimentación y el negro a la "línea", aterrice el luminario. En el caso de equipos con más cables de conexión, identifique el adecuado a la línea de alimentación (todas vienen marcadas con etiquetas) y conéctela a la "línea" de la alimentación, conecte la punta marcada con "com" al neutro de la alimentación. Asegúrese de aislar perfectamente los cables que no utilizó. 5. En los casos en que aplique, reinstale la cubierta del balastro o controlador. 6. Reestablezca la alimentación eléctrica en la caja de fusibles y verifique la operación del luminario. GUARDE ESTAS INSTRUCCIONES U351 Rev. U 07/25/2024 Page 15 of 15
Acuity Brands LightingPage Not FoundnLight® AIR - Networked Lighting Controls | nLight®
Fabricantes de alumbrado publico e iluminación inteligente - CARANDINI
U.S. Environmental Protection Agency | US EPA
Holophane | Lighting solutions for commercial, industrial, emergency and outdoor applications.
Lithonia Lighting® | Best Value in Lighting