Hear. Feel. Connect | Void
voidacoustics.com/eu-declaration-loudspeakersvoidacoustics.com/uk-declaration-loudspeakersTerms & conditions | Void
User Guide for void models including: Arclite 15 Inch 3 Way Arrayable Point Source Loudspeaker 1000W, Arclite, 15 Inch 3 Way Arrayable Point Source Loudspeaker 1000W, Arrayable Point Source Loudspeaker 1000W, Point Source Loudspeaker 1000W, Source Loudspeaker 1000W, Loudspeaker 1000W
Resources & Support | Void
VOID ARCLITE Enceinte Passive de Type 3 Voies 1'190 Watts AES
File Info : application/pdf, 22 Pages, 4.35MB
DocumentDocumentvoidacoustics.com Arclite Designed for Touring USER GUIDE V1.0 ©2023 Void Acoustics Research Ltd. This user guide is subject to change without notice. For the latest online version, visit: www.voidacoustics.com Void Acoustics and the Void logo are registered trademarks of Void Acoustics Research Ltd. in the United Kingdom, USA and other countries; all other Void trademarks are the property of Void Acoustics Research Ltd. Contents 1 Safety and Regulations 1.1 Important Safety Instructions 1.2 Limitations 1.3 EC Declaration of Conformity 1.4 UKCA Conformity 1.5 Warranty Statement 1.6 WEEE Directive 2 Unpacking and Checking 3 About 3.1 Welcome 3.2 Arclite Overview 3.3 Key Features 3.4 Arclite Specifications 3.5 Arclite Dimentions 4 Cable and Wiring 4.1 Electrical Safety 4.2 Cable Considerations for Fixed Installations 4.3 Arclite Wiring Diagram 4.4 Bias D1/Q1/Q1.5/Q2 Phoenix Wiring 4.5 Bias Q3/Q5 speakONTM Wiring 5 Mounting 5.1 Installation Safety 5.2 Horizontal Array 6 Service 6.1 Return Authorisation 6.2 Shipping and Packing Considerations 7 Appendix UG10710-1.0 - Arclite User Guide V1.0 4 4 4 4 4 4 4 5 6 6 6 6 7 8 9 9 9 9 10 10 11 11 12 20 20 20 21 Page 3 1 Safety and Regulations 1.1 Important safety instructions 1.3 EC declaration of conformity The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. For EC Declaration of Conformity please go to: www.voidacoustics.com/eu-declaration-loudspeakers 1.4 UKCA marking For details of the UKCA marking go to: www.voidacoustics.com/uk-declaration-loudspeakers 1.5 Warranty statement Safety instructions - read this first 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat source such as radiators, heat registers, stoves, or other such apparatus that produce heat. 9. Do not defeat the safety purpose of the grounding-type plug. A grounding type plug has two blades and a third grounding prong. The third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect power cords from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit the apparatus. 11. Only use attachments and accessories specified by Void Acoustics. 12. Only use with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug the apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Since the mains power supply cord attachment plug is used to disconnect the device, the plug should always be easily accessible. 16. Void loudspeakers can produce sound levels capable of causing permanent hearing damage from prolonged exposure. The higher the sound level, the less exposure needed to cause such damage. Avoid prolonged exposure to the high sound levels from the loudspeaker. For warranty statement go to: https://voidacoustics.com/terms-conditions/ 1.6 WEEE directive If the time arises to throw away your product, please recycle all the components possible. This symbol indicates that when the end-user wishes to discard this product, it must be sent to separate collection facilities for recovery and recycling. By separating this product from other household-type waste, the volume of waste sent to incinerators or land-fills will be reduced and natural resources will thus be conserved. The Waste Electrical and Electronic Equipment Directive (WEEE Directive) aims to minimise the impact of electrical and electronic goods on the environment. Void Acoustics Research Ltd complies with the Directive 2002/96/EC and 2003/108/EC of the European Parliament on waste electrical finance the cost of treatment and recovery of electronic equipment (WEEE) in order to reduce the amount of WEEE that is being disposed of in land-fill sites. All of our products are marked with the WEEE symbol; this indicates that this product must NOT be disposed of with other waste. Instead it is the user's responsibility to dispose of their waste electrical and electronic equipment by handing it over to an approved reprocessor, or by returning it to Void Acoustics Research Ltd for reprocessing. For more information about where you can send your waste equipment for recycling, please contact Void Acoustics Research Ltd or one of your local distributors. 1.2 Limitations This guide is provided to help familiarise the user with the loudspeaker system and its accessories. It is not intended to provide comprehensive electrical, fire, mechanical and noise training and is not a substitute for industry-approved training. Nor does this guide absolve the user of their obligation to comply with all relevant safety legislation and codes of practice. While every care has been taken in creating this guide, safety is userdependent and Void Acoustics Research Ltd cannot guarantee complete safety whenever the system is rigged and operated. UG10710-1.0 - Arclite User Guide V1.0 Page 4 2 Unpacking and Checking All Void Acoustics products are carefully manufactured and thoroughly tested before being despatched. Your dealer will ensure that your Void products are in pristine condition before being forwarded to you but mistakes and accidents can happen. Before signing for your delivery: · Inspect your shipment for any signs of contamination, abuse or transit damage as soon as you receive it · Check your Void Acoustics delivery fully against your order · If your shipment is incomplete or any of its contents are found to be damaged; inform the shipping company and inform your dealer. When you are removing your Arclite loudspeaker from its original packaging: · Arclite loudspeakers come packaged in a lid and base carton that has a protective sleeve around it; avoid using sharp implements to remove the cardboard to protect the finish · If you need to place the loudspeaker on a flat surface make sure it is free from debris · When you have removed the Arclite loudspeaker from the packaging inspect it to ensure there is no damage and keep all original packaging in case it needs to be returned for any reason. See section 1 for warranty conditions and see section 7 if your product needs servicing. UG10710-1.0 - Arclite User Guide V1.0 Page 5 3 About 3.1 Welcome Many thanks for purchasing this Void Acoustics Arcline Series loudspeaker. We truly appreciate your support. At Void, we design, manufacture and distribute advanced professional audio systems for the installed and live sound market sectors. Like all Void products, our highly skilled and experienced engineers have successfully combined pioneering technologies with groundbreaking design aesthetics, to bring you superior sound quality and visual innovation. In buying this product, you are now part of the Void family and we hope using it brings you years of satisfaction. This guide will help you both use this product safely and ensure it performs to its full capability. 3.2 Arclite overview Designed for pairing with Arcline 218 and 118 subwoofers, Arclite operates as a two-way active, three-way arrayable point source loudspeaker. Offering scalability with maximum output and coherence, to deliver a true point source alternative to the Arcline 8. Tailored for audio integrators and sound engineers with a focus on touring, Arclite guarantees predictable behaviour even in the most demanding applications. An arrays dispersion and sound pressure levels can be configured precisely to best serve any demands. Arclite's design also offers summation up to 20 kHz with minimal destructive interference. Dual NL4 speakONTM connectors with link out and minimal rigging requirements for ground stacked deployments allows for very fast set-up times. 3.3 Key features · Two-way active, three-way arrayable point source · Ground stack or flying configurations available · Asymmetrical combination waveguide and horn optimised with FEA · Dual NL4 speakONTM connector with link out for quick and easy set up · Arrayable in vertical and horizontal configurations · Blanking plate for use without rigging UG10710-1.0 - Arclite User Guide V1.0 Page 6 3 About 3.2.3 Arclite specifications Frequency response Efficiency1 Nominal impedance Power handling2 Maximum output3 Driver configuration Dispersion Connectors Height Width Depth Weight Enclosure Rigging Finish 45 Hz - 18 kHz ±3 dB MHF: 113 dB 1 W / 1 m LF: 98 dB 1 W / 1 m LF: 8 , MHF: 16 LF: 1000 W, MHF 190 W 133 dB Cont, 139 Peak 1 x 15" LF, 1 x 4" MF, 1 x 2.5" HF 35° H x 60° V (25° up - 35° down) 2 x 4-pole speakONTM NL4 793 mm (31.3") 510 mm (20.1") 559 mm (22") 44 kg (97 lbs) 15 mm multi-laminate plywood Ground stack or suspended Textured `TourCoat' polyurea 1 Measured in half space 2 AES2 - 1984 compliant 3 Calculated UG10710-1.0 - Arclite User Guide V1.0 Page 7 3 About 3.5 Arclite dimensions Figure 3.2: Dimensions UG10710-1.0 - Arclite User Guide V1.0 Page 8 4 Cable and Wiring 4.1 Electrical safety To avoid electrical hazards please note the following: · Do not access the inside of any electrical equipment. Refer servicing to Void-approved service agents. 4.2 Cable considerations for fixed installations We recommend specifying installation-grade Low Smoke Zero Halogen (LSZH) cables for permanent installations. The cables should use Oxygen Free Copper (OFC) of grade C11000 or above. Cables for permanent installations should be compliant with the following standards: · IEC 60332.1 Fire retardancy of a single cable · IEC 60332.3C Fire retardancy of bunched cables · IEC 60754.1 Amount of Halogen Gas Emissions · IEC 60754.2 Degree of acidity of released gases · IEC 61034.2 Measurement of smoke density. We suggest using the following maximum copper cable lengths to keep level losses below 0.6 dB. Metric mm2 2.50 mm2 4.00 mm2 Imperial AWG 13 AWG 11 AWG 8 load 36 m 60 m 4 load 18 m 30 m 2 load 9 m 15 m 4.3 Arclite wiring diagram In 1+ 1+ 1- 2- 1- 2+ 2+ 2- Passive crossover Co-Axial 2.5" HF 4" MF + + - - Out/Link 1+ 1+ 1- 2- 1- 2+ 2+ 2- Figure 4.1: Arclite wiring diagram + 15" LF - Phoenix connector UG10710-1.0 - Arclite User Guide V1.0 Page 9 4 Cable and Wiring 4.4 Bias D1/Q1/Q1.5/Q2 phoenix wiring MHF 1MHF 1+ LF 1LF 1+ MHF 1MHF 1+ LF 1LF 1+ LF 1+ LF 1MHF 2+ MHF 2- LF 1+ LF 1MHF 2+ MHF 2- Figure 4.2: Bias D1 Figure 4.3: Bias Q2 Bias D1/Q2 Output Max parallel units Output 1 LF (15") 4 (2 load to amplifier)* Output 2 MHF (4"+2.5") 8 (2 load to amplifier)* *Recommended max parallel units 2 (4 load to amplifier) due to the power rating of the amplifier. 4.5 Bias Q3/Q5 speakONTM wiring LF 1+ LF 1MHF 2+ MHF 2- LF 1+ LF 1MHF 2+ MHF 2- LF 1+ LF 1MHF 2+ MHF 2- Figure 4.4: Bias Q3 Bias Q3/Q5 Output Max quantity per channel Output 1 LF (15") 2 (4 load to amplifier) UG10710-1.0 - Arclite User Guide V1.0 LF 1+ LF 1MHF 2+ MHF 2- Figure 4.5: Bias Q5 Output 2 MHF (4"+2.5") 4 (4 load to amplifier) Page 10 5 Mounting 5.1 Installation safety To avoid mechanical hazards, please note the following: · Safety regulations vary in different regions. Full compliance with those regulations must be your priority · Installations must only be undertaken by fully qualified and experienced engineers/technicians who understand local regulations · This may include consulting a structural engineer before installation of wall brackets · Remember that all personnel have a duty of care to themselves, to their assistants, to the venue staff and to the public · Before lifting any part of the system above head height, check the whole rig for loose tools or other items that may fall and cause injury · Do not use a telephone (even if hands-free) whilst installing. Always concentrate fully on the installation operation · Do not install equipment that is worn, damaged, corroded, mishandled or over- stressed in any way · Use only Void-approved mounting equipment and accessories · Secondary safeties should be provided in all instances where cabinets are flying or fixing overhead and should conform to local regulations UG10710-1.0 - Arclite User Guide V1.0 Page 11 5.2 Horizontal Array 3 4 5 6 7 ISSUE A DATE 12/09/2023 DRAWN JB 8 ECR No CHECKED APPROVED NEW DWG A Parts required: IT4310 - Arclite3 - Vertical Fly Bar Assemb4ly - Black (recommended5 load no more than 6 90KG) IT4165 - Arclite - Top and Bottom Rigging Assy - Black B C 260.0 IT4165 IN-SITU POSITION D IT4310 Figure 5.1: Rigging and fly bar Step 1: Remove all four M6 bolts from the top or bottom infill panels. DESCRIPTION QTY. HANGER CONNECTOR 2 RIGGING MOUNTING PLATE 8.5 1 igging Quick Release Pin 8mm x 40mm 2 F/A WASHER DIN125 A4 STAYBLACK 4 E TITLE: DRAWING No. TOP AND BOTTOM RIGGING ASSY CH10537-101 PROJECT: ARCLITE MATERIAL: AS ABOVE SAP No. IT4165 EST. WEIGHT: (Kg) 1.78 FINISH: COLOUR: BLACK TEXTURE/FINISH: THIRD ANGLE PROJECTION TO BS 8888 SCALE: 1:3 SHT 1 SHEET: OF 1 SHTS A3 8 X 55 HEX BOLT DIN931 A4 ST/ST 2 NI-LOCK NUT DIN985 A4 STAYBLACK 2 55MM LANYARD 2 3 24 F DIMENSIONS IN MILLIMETRES FABRICATION UNLESS OTHERWISE STATED MACHINING UNLESS OTHERWISE STATED UP TO 300mm +/-0,2mm 300mm-500mm +/-0,5mm 500mm - 1m +/-1,0mm 1m - 5m +/-2,0mm ANGULAR ±1° 0, mm 0,0 mm 0,00mm 0,000mm ANGULAR +/- 0,5 mm +/- 0,2 mm +/- 0,1mm +/- 0,01mm ±0,5° BREAK EDGE 0.05 - 0.15mm FILLET RADS 0.1 - 0.3mm SURFACE TEXTURE VALUES IN MICROMETRES (µm) TO BS1134:PT2. ALL MACHINED SURFACES TO BE 1. 6 ALL SCREW THREADS TO BS3643 PT.2: VOIDACOUSTICS.COM REPRODUCTION OF ANY PART OF THIS DOCUMENT IS FORBIDDEN WITHOUT PRIOR PERMISSION FROM VOID ACOUSTICS RESEARCH LTD . Registered in England & Wales No. 07533536 C DESIGN COPYRIGHT RESERVED. CONFIDENTIAL AND PROPRIETARY INFORMATION OF VOID ACOUSTICS RESEARCH LTD. 5 6 7 8 96.0 16.4 ±0.1 THRU 85.0 8.5 Figure 5.2: Bolt removal UG10710-1.0 - Arclite User Guide V1.0 Page 12 DIMENSIONS IN M FABRICATION UNLESS OTHERWISE STATED UP TO 300mm +/-0,2mm 300mm-500mm +/-0,5mm 500mm - 1m +/-1,0mm 1m - 5m +/-2,0mm ANGULAR ±1° 0, mm 0,0 mm 0,00mm 0,000mm ANGULAR SURFACE TEXTURE VALUES IN MICROME 5.2 Horizontal Array Step 2: Remove the infill panel and save it for future use Figure 5.3: Remove infill Step 3: Fix the rigging assembly into place using all fourteen M6 bolts provided. Figure 5.4: Plate fixing UG10710-1.0 - Arclite User Guide V1.0 Page 13 5.2 Horizontal Array Step 4: Place two Arclite together as shown and remove both quick release pins from the rigging assembly Figure 5.5: Quick release Step 5: Rotate the links into position as shown. Figure 5.6: Links UG10710-1.0 - Arclite User Guide V1.0 Page 14 5.2 Horizontal Array Step 6: Reinsert the pins into the rigging assembly of the neighbouring cabinet through the links to fix the top rigging assemblies together. Figure 5.7: Insert pins Step 7: Place the bracket into position as shown and fix with all four pins provided. UG10710-1.0 - Arclite User Guide V1.0 Figure 5.8: Bracket Page 15 5.2 Horizontal Array Step 8: Remove the `R' clip from the rear link assembly. Step 9: Remove the pin Figure 5.9: R-clip release UG10710-1.0 - Arclite User Guide V1.0 Figure 5.10: Remove pin Page 16 5.2 Horizontal Array Step 10: Rotate the relink into position so the holes align Figure 5.11: Rotate link Step 11: Reinsert the pin and `R' clip so that the cabinets are linked together UG10710-1.0 - Arclite User Guide V1.0 Figure 5.12: Link Page 17 5.2 Horizontal Array Step 12: Remove both quick release pins from the rigging assembly. Figure 5.13: Remove pins Step 13: Rotate the links into position as shown. UG10710-1.0 - Arclite User Guide V1.0 Figure 5.14: Links Page 18 5.2 Horizontal Array Step 14: Reinsert the pins into the rigging assembly of the neighbouring cabinet through the links to fix the top rigging assemblies together. Figure 5.15: Insert pins UG10710-1.0 - Arclite User Guide V1.0 Page 19 6 Service Void Arcline loudspeakers should only be serviced by a fully-trained technician. No user serviceable parts inside. Refer servicing to your dealer. 6.1 Return authorisation Before returning your faulty product for repair, please remember to get an R.A.N. (Return Authorisation Number) from the Void dealer who supplied the system to you. Your dealer will handle the necessary paperwork and repair. Failure to go through this return authorisation procedure could delay the repair of your product. Note that your dealer will need to see a copy of your sales receipt as proof of purchase so please have this to hand when applying for return authorisation. 6.2 Shipping and packing considerations · When sending a Void Arcline loudspeaker to an authorised service centre, please write a detailed description of the fault and list any other equipment used in conjunction with the faulty product. · Accessories will not be required. Do not send the instruction manual, cables or any other hardware unless your dealer asks you to. · Pack your unit in the original factory packaging if possible. Include a note of the fault description with the product. Do not send it separately. · Ensure safe transportation of your unit to the authorised service centre. UG10710-1.0 - Arclite User Guide V1.0 Page 20 7 Appendix Architectural specification The loudspeaker shall be a two-way active, three-way arrayable point source, featuring an asymmetrical combination waveguide and horn, consisting of one high power reflex loaded 15" (381 mm) low frequency (LF) transducer, with a two way, mid-high (MHF) coaxial ring radiator compression driver. The low frequency transducer shall be constructed on a rigid metal frame, featuring a 4" (101 mm) voice coil, wound with copper wire on a high-quality voice coil former, for high power handling and long-term reliability. The high frequency coaxial ring radiator shall project its sound through a high precision proprietary waveguide with asymmetrical horn mouth. Performance specifications for a typical production unit shall be as follows: the usable onaxis bandwidth shall be 45 Hz to 18 kHz (±3 dB) for a single enclosure; shall average 35° directivity pattern on the horizontal axis and 60° on the vertical one (25° up - 35° down) (-6 dB down from on-axis level) from 1 kHz to 12 kHz.; maximum SPL of 139 dB peak measured at 1 m using IEC268-5 1/3 Oct pink noise. Power handling shall be 1000 W AES for the LF section at a rated impedance of 8 and 190 W AES for the HF section at a rated impedance of 16 . The wiring connection shall be via two Neutrik speakONTM. One for input and one for loop-out to another speaker, to allow for pre-wiring of the connector before installation. The enclosure shall be constructed from 15 mm multi laminate birch plywood, finished in a textured polyurea and shall contain fixing points so that rigging can be attached to array multiple units in horizontal or vertical configurations. External dimensions shall be (H) 793 mm x (W) 510 mm x (D) 559mm (31.3" x 20.1" x 22") . The weight shall be 44 kg (97lbs). The loudspeaker shall be a Void Acoustics Arclite. UG10710-1.0 - Arclite User Guide V1.0 Page 21 NORTH AMERICA Void Acoustics North America Call: +1 503 854 7134 Email: sales.usa@voidacoustics.com HEAD OFFICE Void Acoustics Research Ltd, Unit 15, Dawkins Road Industrial Estate, Poole, Dorset, BH15 4JY United Kingdom Call: +44(0) 1202 666006 Email: info@voidacoustics.com voidacoustics.com Void Acoustics Research Limited is a company registered in England and Wales registration number 07533536