Manuals+

Sony TC-SD1 Stereo Cassette Deck Service Manual

AEP Model, UK Model, E Model

Manufactured under license from Dolby Laboratories Licensing Corporation. "DOLBY" and the double-D symbol D are trademarks of Dolby Laboratories Licensing Corporation.

Model Name Using Similar Mechanism: TC-PX100

Tape Transport Mechanism Type: TCM-ACLM572

Specifications

Recording system4-track 2-channel stereo (DOLBY NR OFF)
Frequency response30-14,000 Hz (±3 dB), using Sony TYPE I cassettes
30-15,000 Hz (±3 dB), using Sony TYPE II cassettes
30-15,000 Hz (±3 dB), using Sony TYPE IV cassettes
InputTAPE IN (phono jacks): impedance 47 kilohms
OutputTAPE OUT (phono jacks): voltage 500 mV, impedance 47 kilohms
General - Power requirementsEuropean countries model: 220-230 V AC, 50/60 Hz
Other models: 220-240 V AC, 50/60 Hz
Power consumption12 W
DimensionsApprox. 190 x 91 x 315 mm (w/h/d) incl. projecting parts and controls
MassApprox. 3.2 kg
Supplied accessoriesAudio connecting cords (2), System cable (1)

Design and specifications are subject to change without notice.

General

This section is extracted from instruction manual.

Playing a tape

You can use any type of tape, TYPE I (normal), TYPE II (CrO2) or TYPE IV (metal) since the tape deck automatically detects the tape type (ATS*). ATS: Automatic Tape Selection.

This tape deck is able to switch between Dolby B-type and C-type noise reduction systems.

  1. Press [Power] on the CMT-SD1/SD3 to turn on the CMT-SD1/SD3 component system. The tape deck turns on automatically.
  2. Press [Eject] on the tape deck to open the cassette tray and insert a recorded tape. Press again to close the cassette tray.
  3. Set DIRECTION: [ ] to play one side, [ ] to play both sides once, and [ ] to play both sides continuously.
  4. Press [Play]. Press to play the bottom side. The function switches to "TAPE" automatically, then the tape starts playing.

Other operations

Using with CMT-SD1/SD3 system

Do the following operations in step 4:

  1. Press FUNCTION until "TAPE" appears in the display.
  2. Press TAPE on the remote.
  3. To play the bottom side, press TAPE again on the remote.

Remove the cassette

Press [Eject] on the tape deck.

Adjust the volume

Turn VOLUME on the CMT-SD1/SD3 (or VOL/ [Volume Up/Down]*).

* Use the remote supplied with the CMT-SD1/SD3.

**The Automatic Music Sensor (AMS) feature detects a blank space of more than four seconds between tracks to locate tracks quickly.

Tips

Note

Disassembly

Note: Follow the disassembly procedure in the numerical order given.

2-1. Case, Front Panel

This diagram illustrates the disassembly of the case and front panel. It shows the case (4) being lifted off, secured by two screws, case stopper (2). The front panel (8) is attached with two screws (+B 2.6 x 8) (7). A loading panel (6) is also shown, connected via a connector to M901 on the rear side, with pins 5 and 6 of CN05 indicated for external power supply connection.

Diagram shows: Case (4), Front panel (8), Loading panel (6), Screws (+B 2.6 x 8) (3, 7), Screws, case stopper (2), Connector to M901, CN05 connector, Regulated DC power supply.

2-2. Mechanism Deck (TCM-ACLM572)

This diagram shows the mechanism deck (5) being removed from the chassis. It is secured by four screws (+B 3 x 10) and connected via two connectors (4, 3).

Diagram shows: Mechanism deck (TCM-ACLM572) (5), Connectors (3, 4), Screws (+B 3 x 10).

2-3. Control Board, Dolby Board

This diagram illustrates the removal of the control board (4) and Dolby board (7). They are secured by screws and connected via connectors. A clamper is used to fix the harness.

Diagram shows: Control board (4), Dolby board (7), Connectors (1, 5), Screws (+B 2.6 x 8) (2, 3), Harness, Clamper.

2-4. Power Trans Board, AC Select SW Board, Power Board

This diagram shows the removal of the power-related boards. The Power Trans board (3) and Power board (8) are secured by various screws.

Diagram shows: Power Trans board (3), Power board (8), Connector, Support (7), Screws (+B2.6 x 8) (5), (+B2.6 x 8) (6), (+PWH3 x 6) (2), (+B3 x 10) (4).

2-5. Tray Assembly

This diagram shows the tray assembly being removed. It includes an arm, boss, stainless ball, and spring. A note warns to be careful not to drop the stainless ball.

Diagram shows: Tray assembly (5), Arm (576) (4), Boss (3), Stainless ball (5 DIA), Spring (B) (2), Screw (1.7 x 8.2) (1).

2-6. Mechanism Chassis Block

This diagram shows the removal of the mechanism chassis (3) from the chassis block, secured by screws.

Diagram shows: Mechanism chassis (3), Screws (+P 3 x 6) (1), Screw (+P 3 x 8) (2).

2-7. Capstan Reel Motor (M902)

This diagram illustrates the removal of the Capstan reel motor (M902). It is secured by screws, and the belt needs to be hooked. Soldering of the plunger solenoid and motor lead wire must be removed.

Diagram shows: Capstan reel motor (M902) (8), Screws (6), Belt (7), Plunger solenoid, Motor lead wire, Control board (4), Stepped screw (2), Claws (3).

Diagrams

3-1. Circuit Boards Location

This diagram shows the isometric view of the unit with the locations of the various circuit boards identified.

Diagram shows: CONTROL board, REAR PANEL board, CONNECTION board, MODE CONTROL board, FRONT board, POWER TRANS board, POWER board, DOLBY board, O/C SW board, VR board.

3-2. Schematic Diagram -- Display Section --

This schematic diagram details the display section, showing connections between the FRONT BOARD, CONNECTION BOARD, O/C SW BOARD, PANEL SW BOARD, and the CONTROL BOARD. It includes various LEDs, switches, and component labels.

Diagram shows: FRONT BOARD, CONNECTION BOARD, O/C SW BOARD, PANEL SW BOARD, CONTROL BOARD connections. Includes LEDs (FWD-LED, REV-LED, FF-LED, REW-LED, PAUSE-LED, REC-LED, SYNC-LED, LEVELx-LED, PANEL-LED, TAPE-LED, PWR-LED), Switches (SEL5223S, SEL2710K, SEL2410G, SEL2810D-C, etc.), Resistors (R220, R221, R222, R223, R226, R227, R228, R230, R231, R232, R233), Capacitors (C--), and other components. Notes: All resistors are in ohms and 1/4 W or less unless otherwise specified. C: panel designation. U: B+ Line. Components identified by mark ! or dotted line with mark ! are critical for safety.

3-3. Printed Wiring Board -- Display Section --

This section provides the printed wiring board layouts for the display section, showing both the component side and the conductor side for various boards.

Diagram shows: Component and conductor sides of PANEL SW BOARD, CONNECTION BOARD, O/C SW BOARD, FRONT BOARD. Mentions connections to CONTROL BOARD and DOLBY BOARD. Also shows MODE CONTROL BOARD with connections to CAPSTAN/REEL MOTOR (M902), HEAD ASSY (HRPE901), LOADING MOTOR ASSY (M901). Notes: Y: parts extracted from the conductor side. b: Pattern of the rear side.

3-4. Printed Wiring Board -- Main Section --

This section provides the printed wiring board layouts for the main section, showing both the component side and the conductor side for various boards.

Diagram shows: Component and conductor sides of CONTROL BOARD, DOLBY BOARD, POWER BOARD, POWER TRANS BOARD, VR BOARD. Mentions connections to FRONT BOARD, MODE CONTROL BOARD, HEAD ASSY. Notes: Y: parts extracted from the conductor side. b: Pattern of the rear side.

3-5. Schematic Diagram -- Main Section --

This schematic diagram details the main section of the unit, including semiconductor locations and various notes regarding component values and measurement conditions.

Diagram shows: Main section schematic. Notes: All capacitors are in µF unless otherwise noted. pF: µµF. 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in Ω and 1/4 W or less unless otherwise specified. C: panel designation. U: B+ Line. V: B– Line. H: adjustment for repair. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. Signal path indicated. Semiconductor locations listed with Ref. No. and Location (e.g., D01 F-5, IC01 F-5, Q01 F-7).

3-6. IC Block Diagrams

This section provides block diagrams for integrated circuits used in the unit.

IC02 CXA1561S

Block diagram showing functions like METER, PARA, CTRL, DGND, MUTE, NC, REC IN, etc.

IC01 µPC4570HA

Op-amp diagram.

IC03 CXA1598S

Block diagram showing functions like MPXOUT2, LINEOUT2, TCH2, TCL2, RECOUT2, NRSW, REC AMP, VEE, VCC, MODE, etc.

IC04 LA5617

Block diagram showing CURRENT LIMITER, VMUTE, ERROR AMP, START CIRCUIT, OVER HEAT PROTECT.

IC06 LB1641

Block diagram showing MOTOR DRIVE, NOISE FILTER, CLAMP, CONTROL LOGIC.

3-7. IC Pin Function Description

Control Board IC05 TMP87CH48DF (SYSTEM CONTROL)

Pin No.Pin NameI/ODescription
1VSS--System ground terminal
2OSC-OUTOSystem clock output (8 MHz)
3OSC-INISystem clock input (8 MHz)
4RESETIReset input
5NC--No used
6NC--No used
7TESTITest terminal
8POWER-INIPrimary power supply ON/OFF input
9POWER-OUTOMechanism. AU power supply ON/OFF output
10TYPE4OType 4 recording bias selector output
11TYPE2OType 2 recording bias selector output
12TYPE1OType 1 recording bias selector output
13CHROM-SWITape type 2 input
14METAL-SWITape type 4 input
15REC.FWD-SWIRecord safety tab input of side A
16REC.REW-SWIRecord safety tab input of side A
17MODE-SWIHead sensor input
18I2C-CLOCKI/OI2C clock input/output
19I2C-DATAI/OI2C data input/output
20OPEN-SWILoader open switch input
21CLOSE-SWILoader close switch input
22TESTITEST input
23SOLENOIDEOSolenoid output
24CAPSTANOCapstan motor output
25OPEN-MOLoader open (motor) output
26CLOSE-MOLoader close (motor) output
27PANEL-SWIPanel switch input
28OP-VERSIONIOption TC version input
29NC--No used
30AD-GND--AD ground terminal
31AD-REF--AD reference voltage
32VCC--System power input
33KEY1IKey 1 input
34KEY2IKey 2 input
35HALF-SWIHalf switch input
36AMS-INIAMS input
37PULSEIPulse input
38METER-L/RIMeter L-CH input
39I2C-BUSYI/OI2C BUSY input/output
40SYS--No used
41REC/PBOREC/PB selector output
42RELAYORELAY selector output
43BIASOBias selector output
44LINE MUTEOLINE mute selector output
45REC MUTEORecord mute selector output

Continued IC Pin Function Description

Pin No.Pin NameI/ODescription
46PB MUTEOPlayback mute selector output
47DOLBY ON/OFFODolby ON/OFF output
48DOLBY B/CODolby B/C output
49STB-R-LEDONo used
50STB-G-LEDOPower ON LED (green) output
51PANEL-LEDOPanel LED (blue) output
52LEBEL1-LEDOLevel meter 1 (minimum dB) LED (green) output
53LEVEL2-LEDOLevel meter 2 LED (green) output
54LEVEL3-LEDOLevel meter 3 LED (green) output
55LEVEL4-LEDOLevel meter 4 LED (red) output
56LEVEL5-LEDOLevel meter 5 (maximum dB) LED (red) output
57TAPE-LEDOTape indicator LED (amber) output
58CDSYNC-LEDOCD synchro LED (red) output
59REC-LEDOREC LED (red) output
60PAUSE-LEDOPAUSE LED (orange) output
61REW-LEDOREW LED (amber) output
62FF-LEDOFF LED (amber) output
63REV-LEDOREV LED (green) output
64FWD-LEDOFWD LED (green) output

Mechanical Adjustment

Precaution

  1. Clean the following parts with a denatured alcohol-moistened swab: record/playback heads, pinch rollers, erase head, rubber belts, capstan, idlers.
  2. Do not use a magnetized screwdriver for the adjustments.
  3. After the adjustments, apply suitable locking compound to the parts adjusted.
  4. The adjustments should be performed with the rated power supply voltage unless otherwise noted.

Torque Measurement

ModeTorque meterMeter reading
FWDCQ-102C31 to 61 g·cm
FWD back tension2 to 6 g·cm
REVCQ-102RC36 to 61 g·cm
REV back tension2 to 6 g·cm
FF/REWCQ-201B61 to 143 g·cm

Tape Tension

Torque meter
FWD tensionCQ-403A100 g or more
REV tensionCQ-403R100 g or more

Electrical Adjustment

Precaution

  1. Perform adjusting on the test mode.
  2. Demagnetize the record/playback head with a head demagnetizer.
  3. Do not use a magnetized screwdriver for the adjustments.
  4. After the adjustments, apply suitable locking compound to the parts adjust.
  5. The adjustments should be performed with the rated power supply voltage unless otherwise noted.
  6. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.)
  7. The adjustments should be performed for both L-CH and R-CH.
  8. Switches should be set as follows.

Standard Recording Position

Adjust the REC LEVEL (VR02) control so that the standard input/output signal level is obtained in the following connection.

Record Mode

Diagram shows audio oscillator connected to attenuator (10k Ω), then to set input (600 Ω LINE IN), and output from LINE OUT to level meter.

Standard Input Level

Input terminalLINE IN
Source impedance10kΩ
Input signal level0.5V (–3.8dB)

Standard Output Level

Output terminalLINE OUT
Load impedance47kΩ
Output signal level0.5V (–3.8dB)

0dB = 0.775 V

Test Mode

Turn OFF the main power and insert the shorting plug to the test point CN13 (2P) on the CONTROL board (setting IC05 pin 22 to "L"). Then turn ON the main power which activate the TEST mode. All displays flash once. If a recording is performed in the TEST mode, the REC MEMORY mode becomes active at the moment of recording so that the tape is rewound by the amount of recording when a tape is rewound after recording. After adjustment, be sure to remove the shorting plug from the test point CN13 (2P).

Test Tape

TypeSignalUsed for
P-4-A10010 kHz, –10 dBAzimuth Adjustment
WS-48B3 kHz, 0 dBTape Speed Adjustment
P-4-L300315 Hz, 0 dBPB Level Adjustment

Record/Playback Head Azimuth Adjustment

Note: Perform this adjustment after the head is turned around. (If the head is positioned in the FWD direction, turn around the head and start adjustment from the REV mode as described below.)

When the azimuth adjustment is performed, the azimuth adjustment screw must end up with rotation of tightening direction (i.e. clockwise direction).

Adjustment procedure

  1. Mode: REV playback. Test tape: P-4-A100 (10kHz, –10dB). Connect to level meter via 47kΩ.
  2. Turn the azimuth adjustment screw for the maximum output level of L-CH and R-CH. If the peak levels do not match for L-CH and R-CH, turn the adjustment screw until both of output levels match together within 1 dB of peak.
  3. Phase Check. Mode: REV playback. Test tape: P-4-A100 (10kHz, –10dB). Connect L-CH and R-CH to oscilloscope via 47kΩ and LINE OUT.
  4. Enter the FWD mode and perform steps 1 to 3.
  5. Check that the phase difference between L-CH and R-CH is in the range of in-phase to 90°.
  6. After adjustment, lock the screw with locking compound.

Diagram shows oscilloscope Lissajous waveform examples for phase check (in phase, 45°, 90°, 135°, 180°).

Adjustment Location

Diagram shows adjustment screw locations on the FWD and REV sides.

Tape Speed Adjustment

Procedure

  1. Mode: FWD playback. Test tape: WS-48B (3kHz, 0dB). Connect to frequency counter via 47kΩ and LINE OUT.
  2. Adjust the adjustment control (variable resistor) of the motor (M902) until the frequency counter reading becomes 3,000 Hz ± 90 Hz.
  3. Confirm that the tape speed deviation between tape top and tape end is within 3%.

Adjustment location

Diagram shows M902 motor and adjustment control.

Sample Value of Wow and flutter

W. RMS (JIS) within 0.3% (test tape: WS-48B).

Playback Level Adjustment

Procedure

  1. Mode: FWD playback. Test tape: P-4-L300 (315Hz, 0dB). Connect to level meter via 47kΩ and LINE OUT.
  2. Adjust SFR01 (L-CH) and SFR02 (R-CH) so that the reading on level meter meets the adjustment limits below.

Adjustment Limits

LINE OUT level: –7.7 ± 0.5 dB (301.5 to 338.5 mV). Level difference between channels: within 0.5 dB. Check that the LINE OUT level does not change even if Playback and Stop operations are repeated several times.

Adjustment Location

DOLBY board (Refer to page 32).

Record BIAS Adjustment

Setting

Procedure

  1. Mode: Record. Connect AF OSC to attenuator, then to 600 Ω LINE IN. Use blank tape CS-123. Output via LINE OUT to level meter.
  2. Playback recorded portion.
  3. Reproduce the portion of tape which is recorded in step 1. Confirm that the playback level stays within the specified range of the Adjustment Level.
  4. If the playback level is outside the specified range, adjust the SFR11 (L-CH) and SFR12 (R-CH), and repeat steps 1 to 3 until the specified range is satisfied.

Adjustment Level

–23.8 dB ± 0.5 dB (47.3 to 53.1 mV).

Adjustment Location

DOLBY board (Refer to page 32).

Record Level Adjustment

Setting

Procedure

  1. Record. Connect AF OSC to attenuator, then to 600 Ω LINE IN. Use blank tape CS-123. Output via LINE OUT to level meter.
  2. Playback recorded portion.
  3. Reproduce the portion of tape which is recorded in step 1. Confirm that the playback level stays within the specified range of the Adjustment Level.
  4. If the playback level is outside the specified range, adjust the SFR03 (L-CH) and SFR04 (R-CH), and repeat steps 1 to 3 until the specified range is satisfied.

Adjustment Level

Difference of the playback level between 10 kHz and 315 Hz: 0 dB ± 0.5 dB when 315 Hz is the reference.

Adjustment Location

DOLBY board (Refer to page 32).

Adjustment Locations

DOLBY board (Component Side)

Diagram shows locations of SFR01, SFR02, SFR03, SFR04, SFR11, SFR12, IC01, IC02, IC03.

CONTROL board (Component Side)

Diagram shows location of CN13, IC01, IC05.

Exploded Views

6-1. Case, Front Panel Section

This section provides an exploded view of the case and front panel assembly, with a list of parts.

Ref. No.Part No.DescriptionRemarks
13-033-056-01WINDOW, GLASS
24-212-579-11BRACKET (GLASS)
34-942-636-21EMBLEM (NO.3.5), SONY
44-214-458-01TAPE
53-033-074-01CHASSIS, FRONT
63-033-079-01REC LEVEL KNOB
73-028-756-01PANEL (AL-TC), LOADING
83-033-054-01PLATE, LOADING ORNAMENT
93-033-055-01LID, LOADING
103-028-755-01PANEL (AL-TC), FRONT
113-033-057-01SCREW, CASE STOPPER
123-033-052-01TOP COVER
133-033-053-01FOOT
143-033-061-01FOOT CUSHION
151-773-128-11WIRE (FLAT TYPE) (19 CORE)
16A-2007-825-ACONNECTION BOARD, COMPLETE*
173-033-080-01DOLBY KNOB
183-033-078-01DIRECTION KNOB
194-212-557-01BUTTON (REC)
203-033-075-01LENS
21A-2007-817-AFRONT BOARD, COMPLETE*
223-033-076-01BUTTON, PLAY
233-033-077-01BUTTON, FF
24A-2007-823-AO/C SW BOARD, COMPLETE*
251-672-765-11VR BOARD*
263-033-081-01REC LEBEL BRACKET
273-033-082-01VR WASHER 90
283-033-083-01NUT, VR
314-212-539-02BUTTON (POWER)

6-2. Chassis Section

Ref. No.Part No.DescriptionRemarks
513-033-060-01SPRING, PLATE
524-213-692-02TAPE (SPRING)
53X-4950-381-1BRACKET (R) ASSY
543-033-050-01HINGE (L/C), DOOR
55A-2007-818-ADOLBY BOARD, COMPLETE*
563-033-063-01CHASSIS (R), DECK
573-033-062-01CHASSIS (L), DECK
58A-2007-819-ACONTROL BOARD, COMPLETE*
59A-2007-820-APOWER BOARD, COMPLETE*
601-672-764-11POWER TRANS BOARD*
613-035-607-01REAR PANEL (AEP, UK)*
613-035-608-01REAR PANEL (E, HK, SP)*
623-033-068-01CUSHION
631-555-750-00CORD, POWER!
643-033-071-01STOPPER, AC CORD
651-526-794-11OUTLET, AC!
66A-2007-824-APANEL SW BOARD, COMPLETE*
T011-433-657-11TRANSFORMER, POWER!

6-3. Mechanism Deck Section-1 (TCM-ACLM572)

Ref. No.Part No.DescriptionRemarks
1013-017-214-01HOLDER
1023-017-215-01ARM (A)
1033-017-233-01RACK, GEAR
1043-017-216-01ARM (C)
1053-017-213-01CHASSIS
1063-017-212-01TRAY
1073-017-235-01SPRING (A)
1083-017-244-01SCREW (1.7 × 8.2), SPECIAL
1093-017-217-01ARM (576)
1103-017-218-01RETAINER
1113-017-219-01PLATE
1123-017-211-01FRAME
1133-017-236-01SPRING (B)
1143-017-234-01GROUND, PLATE
1153-017-243-01NUT
1163-017-242-01BUFFER
1173-017-232-01GEAR (B)
1183-017-241-01SCREW (1.6 × 4), SPECIAL
1193-017-237-01BELT (49.2)
1203-017-231-01PULLEY (C)
1213-017-220-01ARM
1223-017-240-01SCREW (2.1 × 4), SPECIAL
M9013-017-239-01PULLEY (MOTOR) (LOADING)
S9013-017-238-01LIMITTER (SW MSS-8B) (OPEN)
S9023-017-238-01LIMITTER (SW MSS-8B) (CLOSE)

6-4. Mechanism Deck Section-2 (TCM-ACLM572)

Ref. No.Part No.DescriptionRemarks
1513-017-294-01SCREW (S), SPECIAL
1533-017-273-01LEVER (AC), SPRING
1543-017-270-01AC, LEVER
1553-017-279-01SCREW (M2), SPECIAL
1563-017-274-01HEAD, SPRING BASE
1573-017-254-01PINCH ROLLER (F)
1583-017-253-01CHASSIS (HEAD)
1593-017-277-01PINCH (F), SPRING
1603-017-278-01PINCH (R), SPRING
1613-017-300-01WASHER, FLAT
1623-017-255-01PINCH ROLLER (R)
1633-017-296-01CUSHION (MOTOR)
1643-017-297-01SCREW (MOTOR)
1653-017-280-01SCREW (M2 TAPPING), SPECIAL
1663-017-285-01BELT (MAIN)
1671-672-011-11MODE CONTROL BOARD*
HRPE9013-017-303-01HEAD (REC/PLAY/ERASE)
M9023-017-259-01PULLEY (MOTOR) (CAPSTAN REEL)

6-5. Mechanism Deck Section-3 (TCM-ACLM572)

Ref. No.Part No.DescriptionRemarks
2013-017-258-01FLYWHEEL (R)
2023-017-257-01FLYWHEEL (F)
2033-017-284-01BELT (SUB)
2043-017-265-01IDLER, GEAR
2053-017-305-01GEAR (P)
2063-017-283-01WASHER, FLAT
2073-017-304-01CLUTCH
2083-017-263-01REEL, BASE
2093-017-295-01WASHER, FLAT
2103-017-252-01CHASSIS (OS)
2113-017-298-01WASHER (B/T)
2123-017-299-01SPRING (B/T) (F)
2133-017-288-01REEL, CAP
2143-017-262-01REEL, BUSHING
2153-017-272-01SPRING (BT)
2163-017-281-01WASHER, FLAT
2173-017-256-01ARM (PLAY)
2183-017-275-01LOCK, SPRING CAM
2193-017-267-01LOCK, ARM CAM
2203-017-282-01WASHER, FLAT
2213-017-264-01CAM, GEAR
2223-017-266-01BASE, LEVER
2233-017-268-01ARM (RF)
2243-017-269-01GEAR (RF)
2253-017-276-01ARM (RF), SPRING
2263-017-293-01MAGNET, PLATE
2273-017-271-01CAP (MG)

Electrical Parts List

Connection Board

Ref. No.Part No.DescriptionRemarks
*A-2007-825-ACONNECTION BOARD, COMPLETE
CN051-564-708-11PIN, CONNECTOR (SMALL TYPE) 6P
CN071-785-785-11SOCKET, CONNECTOR 10P
CN081-564-715-11PIN, CONNECTOR (SMALL TYPE) 13P
CN091-568-802-11SOCKET, CONNECTOR 19P
CN121-785-779-11SOCKET, CONNECTOR 13P
CN12A1-785-780-11HEADER, PIN 13P
CN141-564-704-11PIN, CONNECTOR (SMALL TYPE) 2P*

Resistor

Part No.Description
R2211-247-855-11CARBON10K 5% 1/4W
R2251-247-839-11CARBON2.2K 5% 1/4W
R2261-247-843-11CARBON3.3K 5% 1/4W
R2271-247-863-11CARBON22K 5% 1/4W
R2281-247-871-11CARBON47K 5% 1/4W

Switch

Part No.Description
S71-572-647-11SWITCH, KEY BOARD (POWER)
S111-692-505-11SWITCH, SLIDE (DIRECTION)
S121-692-505-11SWITCH, SLIDE (DOLBY NR)

Diode

Part No.Description
D028-719-911-19DIODE 1SS119
D038-719-911-19DIODE 1SS119
D048-719-911-19DIODE 1SS119
D138-719-109-97DIODE RD6.8ES-B2
D148-719-109-85DIODE RD5.1ES-B2
D158-719-911-19DIODE 1SS119
D168-719-109-85DIODE RD5.1ES-B2
D198-719-055-76DIODE 1N4148
D208-719-911-19DIODE 1SS119
D288-719-200-02DIODE 10E2

Capacitor

Part No.Description
C681-162-282-31CERAMIC100PF 10% 50V
C691-137-372-11FILM0.022uF 5% 50V
C701-162-217-31CERAMIC56PF 5% 50V
C711-126-961-11ELECT2.2uF 20% 50V
C731-126-960-11ELECT1uF 20% 50V
C741-126-916-11ELECT1000uF 20% 6.3V
C751-161-494-00CERAMIC0.022uF 25V
C761-126-964-11ELECT10uF 20% 50V
C771-164-159-11CERAMIC0.1uF 50V
C781-162-306-11CERAMIC0.01uF 20% 16V
C791-162-306-11CERAMIC0.01uF 20% 16V
C811-126-935-11ELECT470uF 20% 16V
C821-126-934-11ELECT220uF 20% 16V
C831-162-282-31CERAMIC100PF 10% 50V
C70A1-126-964-11ELECT10uF 20% 50V
C74A1-164-159-11CERAMIC0.1uF 50V
C76A1-126-963-11ELECT4.7uF 20% 50V
C76B1-104-664-11ELECT47uF 20% 16V
C77A1-164-159-11CERAMIC0.1uF 50V

Filter

Part No.Description
CF011-579-125-11VIBRATOR, CERAMIC 8MHz

IC

Part No.Description
IC058-759-575-34IC TMP87CH48DF-4B67
IC068-759-822-09IC LB1641
IC078-759-165-85IC PST600H-T
IC088-759-710-59IC NJM4580D-D

Transistor

Part No.Description
Q198-729-119-76TRANSISTOR 2SA1175-HFE
Q218-729-900-63TRANSISTOR DTA124ES
Q228-729-900-63TRANSISTOR DTA124ES
Q238-729-900-63TRANSISTOR DTA124ES
Q248-729-993-43TRANSISTOR 2SA934R
Q258-729-993-43TRANSISTOR 2SA934R
Q268-729-029-86TRANSISTOR DTC124ESA
Q278-729-029-86TRANSISTOR DTC124ESA
Q298-729-900-63TRANSISTOR DTA124ES
Q308-729-900-63TRANSISTOR DTA124ES
Q318-729-900-63TRANSISTOR DTA124ES
Q328-729-900-63TRANSISTOR DTA124ES
Q338-729-900-63TRANSISTOR DTA124ES
Q348-729-900-63TRANSISTOR DTA124ES
Q358-729-900-63TRANSISTOR DTA124ES
Q368-729-900-63TRANSISTOR DTA124ES
Q388-729-900-63TRANSISTOR DTA124ES

Control Board

Ref. No.Part No.DescriptionRemarks
*A-2007-819-ACONTROL BOARD, COMPLETE
R2211-247-855-11CARBON10K 5% 1/4W
R2251-247-839-11CARBON2.2K 5% 1/4W
R2261-247-843-11CARBON3.3K 5% 1/4W
R2271-247-863-11CARBON22K 5% 1/4W
R2281-247-871-11CARBON47K 5% 1/4W
R761-249-437-11CARBON47K 5% 1/4W
R771-249-427-11CARBON6.8K 5% 1/4W F
R781-247-843-11CARBON3.3K 5% 1/4W
R791-247-879-11CARBON100K 5% 1/4W
R801-247-879-11CARBON100K 5% 1/4W
R811-247-855-11CARBON10K 5% 1/4W
R821-249-417-11CARBON1K 5% 1/4W
R831-249-432-11CARBON18K 5% 1/4W
R841-249-436-11CARBON39K 5% 1/4W
R851-247-879-11CARBON100K 5% 1/4W
R861-249-417-11CARBON1K 5% 1/4W F
R871-249-413-11CARBON470 5% 1/4W F
R881-247-855-11CARBON10K 5% 1/4W
R891-247-855-11CARBON10K 5% 1/4W
R901-249-417-11CARBON1K 5% 1/4W F
R911-249-417-11CARBON1K 5% 1/4W F
R961-247-855-11CARBON10K 5% 1/4W
R971-249-417-11CARBON1K 5% 1/4W F
R981-247-855-11CARBON10K 5% 1/4W
R991-249-417-11CARBON1K 5% 1/4W F
R1001-247-807-11CARBON100 5% 1/4W
R1011-247-855-11CARBON10K 5% 1/4W
R1021-247-847-11CARBON4.7K 5% 1/4W
R1031-247-807-11CARBON100 5% 1/4W
R1041-249-427-11CARBON6.8K 5% 1/4W F
R1051-249-427-11CARBON6.8K 5% 1/4W F
R1071-249-398-11CARBON27 5% 1/4W F
R1091-247-867-11CARBON33K 5% 1/4W
R1101-247-807-11CARBON100 5% 1/4W
R1111-247-879-11CARBON100K 5% 1/4W
R1121-249-430-11CARBON12K 5% 1/4W
R1131-249-440-11CARBON82K 5% 1/4W
R1141-249-417-11CARBON1K 5% 1/4W F
R1161-249-427-11CARBON6.8K 5% 1/4W F
R1171-249-412-11CARBON390 5% 1/4W F
R20A1-247-855-11CARBON10K 5% 1/4W
R2001-249-412-11CARBON390 5% 1/4W F
R2011-249-412-11CARBON390 5% 1/4W F
R2021-249-412-11CARBON390 5% 1/4W F
R2031-249-412-11CARBON390 5% 1/4W F
R2041-249-409-11CARBON220 5% 1/4W F
R2051-249-409-11CARBON220 5% 1/4W F
R2061-249-412-11CARBON390 5% 1/4W F
R2071-249-412-11CARBON390 5% 1/4W F
R2081-249-412-11CARBON390 5% 1/4W F
R2091-249-412-11CARBON390 5% 1/4W F
R2101-249-412-11CARBON390 5% 1/4W F
R2111-249-412-11CARBON390 5% 1/4W F
R2121-249-412-11CARBON390 5% 1/4W F
R2141-249-412-11CARBON390 5% 1/4W F
R4041-249-437-11CARBON47K 5% 1/4W
R102A1-247-855-11CARBON10K 5% 1/4W

Dolby Board

Ref. No.Part No.DescriptionRemarks
*A-2007-818-ADOLBY BOARD, COMPLETE
CN011-564-707-11PIN, CONNECTOR (SMALL TYPE) 5P
CN041-785-778-11SOCKET, CONNECTOR 8P
D018-719-911-19DIODE 1SS119
D058-719-911-19DIODE 1SS119
D068-719-911-19DIODE 1SS119
IC018-759-112-93IC UPC4570HA-1
IC028-752-060-46IC CXA1561S
IC038-752-070-69IC CXA1598S
L011-414-223-11INDUCTOR470uH
L021-414-223-11INDUCTOR470uH
L031-410-780-11INDUCTOR27mH
L041-410-780-11INDUCTOR27mH
L071-429-316-11TRANSFORMER, BIAS OSCILLATION (BIAS)
LPF051-236-087-11FILTER, LOW PASS
LPF061-236-087-11FILTER, LOW PASS

Resistor

Part No.Description
R111-247-855-11CARBON10K 5% 1/4W
R121-247-855-11CARBON10K 5% 1/4W
R131-247-843-11CARBON3.3K 5% 1/4W
R141-247-843-11CARBON3.3K 5% 1/4W
R151-249-431-11CARBON15K 5% 1/4W
R161-249-431-11CARBON15K 5% 1/4W
R171-249-387-11CARBON3.3 5% 1/4W F
R181-247-847-11CARBON4.7K 5% 1/4W
R191-249-390-11CARBON5.6 5% 1/4W F
R201-249-432-11CARBON18K 5% 1/4W
R211-249-432-11CARBON18K 5% 1/4W
R221-249-424-11CARBON3.9K 5% 1/4W F
R231-249-432-11CARBON18K 5% 1/4W
R241-249-420-11CARBON1.8K 5% 1/4W F
R251-247-838-11CARBON2K 5% 1/4W
R281-247-855-11CARBON10K 5% 1/4W
R291-247-855-11CARBON10K 5% 1/4W
R301-247-855-11CARBON10K 5% 1/4W
R311-247-855-11CARBON10K 5% 1/4W
R321-247-843-11CARBON3.3K 5% 1/4W
R331-247-843-11CARBON3.3K 5% 1/4W
R341-249-428-11CARBON8.2K 5% 1/4W F
R361-247-863-11CARBON22K 5% 1/4W
R371-247-863-11CARBON22K 5% 1/4W
R381-249-418-11CARBON1.2K 5% 1/4W F

Transistor

Part No.Description
Q018-729-029-86TRANSISTOR DTC124ESA
Q028-729-029-86TRANSISTOR DTC124ESA
Q038-729-029-68TRANSISTOR DTC114TSA
Q048-729-029-68TRANSISTOR DTC114TSA
Q058-729-231-55TRANSISTOR 2SC2878-AB
Q068-729-231-55TRANSISTOR 2SC2878-AB
Q078-729-029-86TRANSISTOR DTC124ESA
Q088-729-142-46TRANSISTOR 2SC2001-LK
Q098-729-142-46TRANSISTOR 2SC2001-LK
Q108-729-140-96TRANSISTOR 2SD774-34
Q118-729-900-63TRANSISTOR DTA124ES
Q128-729-029-86TRANSISTOR DTC124ESA
Q138-729-029-86TRANSISTOR DTC124ESA
Q148-729-029-68TRANSISTOR DTC114TSA
Q158-729-029-68TRANSISTOR DTC114TSA
Q168-729-029-86TRANSISTOR DTC124ESA
Q178-729-029-86TRANSISTOR DTC124ESA
Q188-729-029-86TRANSISTOR DTC124ESA
Q458-729-194-57TRANSISTOR 2SC945-P
Q12A8-729-900-63TRANSISTOR DTA124ES
Q13A8-729-900-63TRANSISTOR DTA124ES

Resistor

Part No.Description
R391-249-418-11CARBON1.2K 5% 1/4W F
R401-247-863-11CARBON22K 5% 1/4W
R411-247-863-11CARBON22K 5% 1/4W
R441-247-883-00CARBON150K 5% 1/4W
R451-249-428-11CARBON8.2K 5% 1/4W F
R461-249-428-11CARBON8.2K 5% 1/4W F
R491-247-839-11CARBON2.2K 5% 1/4W
R501-247-839-11CARBON2.2K 5% 1/4W
R511-247-839-11CARBON2.2K 5% 1/4W
R521-247-839-11CARBON2.2K 5% 1/4W
R531-247-843-11CARBON3.3K 5% 1/4W
R541-247-843-11CARBON3.3K 5% 1/4W
R551-249-417-11CARBON1K 5% 1/4W F
R561-249-417-11CARBON1K 5% 1/4W F
R571-249-436-11CARBON39K 5% 1/4W
R581-249-431-11CARBON15K 5% 1/4W
R591-247-879-11CARBON100K 5% 1/4W
R601-249-439-11CARBON68K 5% 1/4W
R611-247-867-11CARBON33K 5% 1/4W
R621-247-883-00CARBON150K 5% 1/4W
R631-249-438-11CARBON56K 5% 1/4W
R641-249-432-11CARBON18K 5% 1/4W
R651-247-883-00CARBON150K 5% 1/4W
R661-249-430-11CARBON12K 5% 1/4W
R671-247-849-11CARBON5.6K 5% 1/4W
R011-247-881-00CARBON120K 5% 1/4W
R021-247-881-00CARBON120K 5% 1/4W
R031-247-881-00CARBON120K 5% 1/4W
R041-247-881-00CARBON120K 5% 1/4W
R051-247-850-11CARBON6.2K 5% 1/4W
R061-247-850-11CARBON6.2K 5% 1/4W
R071-249-404-00CARBON82 5% 1/4W F
R081-249-404-00CARBON82 5% 1/4W F
R091-247-839-11CARBON2.2K 5% 1/4W
R101-247-839-11CARBON2.2K 5% 1/4W
R01A1-249-393-11CARBON10 5% 1/4W F
R0151-249-409-11CARBON220 5% 1/4W F

Front Board

Ref. No.Part No.DescriptionRemarks
*A-2007-817-AFRONT BOARD, COMPLETE
CN091-785-783-11CONNECTOR, FFC/FPC 19P
LED18-719-072-76LED SEL5E23C-TP15 (REV)
LED28-719-072-76LED SEL5E23C-TP15 (PLAY)
LED38-719-072-76LED SEL5E23C-TP15 (PAUSE)
LED48-719-072-76LED SEL5E23C-TP15 (STOP)
LED58-719-304-83LED SEL2410G (-10)
LED68-719-304-83LED SEL2410G (-5)
LED78-719-304-83LED SEL2410G (0)
LED88-719-812-41LED TLR124 (+3)
LED98-719-812-41LED TLR124 (+6)
LED108-719-058-04LED SEL5223S-TP15 (CD SYNC)
LED118-719-058-04LED SEL5223S-TP15 (REC)
LED128-719-300-97LED SEL2710K (PAUSE)
LED138-719-311-60LED SEL2810D-C (REW)
LED148-719-311-60LED SEL2810D-C (FF)
LED158-719-304-83LED SEL2410G (REV)
LED168-719-304-83LED SEL2410G (PLAY)
LED178-719-304-83LED SEL2410G ()
LED188-719-812-41LED TLR124 (TAPE)
S11-572-647-11SWITCH, KEY BOARD (STOP)
S21-572-647-11SWITCH, KEY BOARD (PAUSE)
S31-572-647-11SWITCH, KEY BOARD (PLAY)
S41-572-647-11SWITCH, KEY BOARD (REV)
S51-572-647-11SWITCH, KEY BOARD (CD SYNC)
S61-572-647-11SWITCH, KEY BOARD (REC)
S91-572-647-11SWITCH, KEY BOARD (FF)
S101-572-647-11SWITCH, KEY BOARD (REW)
S0013-017-290-01DETECT, SWITCH (FWD REC)
S0023-017-290-01DETECT, SWITCH (HALF)
S0033-017-290-01DETECT, SWITCH (CrO2)
S0043-017-290-01DETECT, SWITCH (METAL)
S0053-017-290-01DETECT, SWITCH (REV REC)
S0063-017-291-01MODE, SWITCH (MODE)
R0011-247-862-11CARBON20K 5% 1/4W

Mode Control Board

Part No.Description
1-672-011-11MODE CONTROL BOARD
3-017-287-01TERMINAL (RP)

Diode

Part No.Description
D0018-719-911-19DIODE 1N4148M
D0028-719-911-19DIODE 1N4148M

IC

Part No.Description
IC0013-017-289-01PLATE, ROTARY DETECTION

Plunger Solenoid

Part No.Description
PM0013-017-292-01SOLENOID

Resistor

Part No.Description
R2151-247-827-11CARBON680 5% 1/4W
R2161-249-417-11CARBON1K 5% 1/4W F
R2171-247-835-11CARBON1.5K 5% 1/4W
R2181-247-839-11CARBON2.2K 5% 1/4W
R2191-247-843-11CARBON3.3K 5% 1/4W
R2201-247-847-11CARBON4.7K 5% 1/4W
R2221-247-827-11CARBON680 5% 1/4W
R2231-249-417-11CARBON1K 5% 1/4W F
R2241-247-835-11CARBON1.5K 5% 1/4W
R2301-249-409-11CARBON220 5% 1/4W F
R2311-249-409-11CARBON220 5% 1/4W F
R2321-249-409-11CARBON220 5% 1/4W F
R2331-249-409-11CARBON220 5% 1/4W F

O/C SW Board

Ref. No.Part No.DescriptionRemarks
*A-2007-823-AO/C SW BOARD, COMPLETE
S81-572-647-11SWITCH, KEY BOARD (EJECT)

Panel SW Board

Ref. No.Part No.DescriptionRemarks
*A-2007-824-APANEL SW BOARD, COMPLETE
S151-771-612-11SWITCH, DETECTION (PANEL SW)

Power Board

Ref. No.Part No.DescriptionRemarks
*A-2007-820-APOWER BOARD, COMPLETE
C311-162-290-31CERAMIC470PF 10% 50V
C321-162-290-31CERAMIC470PF 10% 50V
C481-126-925-11ELECT470uF 20% 10V
C491-126-925-11ELECT470uF 20% 10V
C501-164-159-11CERAMIC0.1uF 50V
C511-162-294-31CERAMIC0.001uF 10% 50V
C521-162-294-31CERAMIC0.001uF 10% 50V
C531-164-159-11CERAMIC0.1uF 50V
C541-126-943-11ELECT2200uF 20% 25V
C551-126-943-11ELECT2200uF 20% 25V
C561-126-943-11ELECT2200uF 20% 25V
C571-162-306-11CERAMIC0.01uF 20% 16V
C581-126-926-11ELECT1000uF 20% 10V
C591-126-960-11ELECT1uF 20% 50V
C841-102-129-00CERAMIC10000PF 10% 50V
C851-102-129-00CERAMIC10000PF 10% 50V
C861-102-129-00CERAMIC10000PF 10% 50V
C871-102-129-00CERAMIC10000PF 10% 50V
C901-164-159-11CERAMIC0.1uF 50V
C911-164-159-11CERAMIC0.1uF 50V
C90A1-124-261-00ELECT10uF 20% 50V

Power Trans Board

Ref. No.Part No.DescriptionRemarks
*1-672-764-11POWER TRANS BOARD
T011-433-657-11TRANSFORMER, POWER!

Resistor

Part No.Description
R261-247-879-11CARBON100K 5% 1/4W
R271-247-879-11CARBON100K 5% 1/4W
R351-247-855-11CARBON10K 5% 1/4W
R421-247-839-11CARBON2.2K 5% 1/4W
R431-247-839-11CARBON2.2K 5% 1/4W
R1151-247-855-11CARBON10K 5% 1/4W
R1191-247-713-11CARBON1K 5% 1/4W F
R1201-247-855-11CARBON10K 5% 1/4W
R1211-247-855-11CARBON10K 5% 1/4W
R1221-247-855-11CARBON10K 5% 1/4W
R1231-249-417-11CARBON1K 5% 1/4W F
R1241-247-879-11CARBON100K 5% 1/4W
R1251-247-855-11CARBON10K 5% 1/4W
R1261-247-855-11CARBON10K 5% 1/4W
R2131-247-863-11CARBON22K 5% 1/4W
R3021-247-879-11CARBON100K 5% 1/4W
R3031-249-417-11CARBON1K 5% 1/4W F
R3041-249-417-11CARBON1K 5% 1/4W F
R3051-247-879-11CARBON100K 5% 1/4W
R3061-247-807-11CARBON100 5% 1/4W
R3071-247-807-11CARBON100 5% 1/4W
R35A1-249-417-11CARBON1K 5% 1/4W F
R38A1-247-847-11CARBON4.7K 5% 1/4W
R39A1-247-847-11CARBON4.7K 5% 1/4W

Connector

Part No.Description
CN031-566-856-11SOCKET, CONNECTOR 5P (SYSTEM CONTROL)
CN041-785-781-11HEADER, PIN 8P
CN061-564-707-11PIN, CONNECTOR (SMALL TYPE) 5P
CN071-785-782-11HEADER, PIN 10P
CN151-564-706-11PIN, CONNECTOR (SMALL TYPE) 4P
CN12A1-785-780-11HEADER, PIN 13P

Diode

Part No.Description
D078-719-991-33DIODE 1SS133T-77
D128-719-031-85DIODE 1N4002L
D178-719-073-77DIODE W005M
D228-719-031-85DIODE 1N4002L
D238-719-031-85DIODE 1N4002L
D248-719-031-85DIODE 1N4002L
D258-719-031-85DIODE 1N4002L
D368-719-991-33DIODE 1SS133T-77
D378-719-991-33DIODE 1SS133T-77

Transistor

Part No.Description
Q208-729-119-78TRANSISTOR 2SC403SP-51
Q378-729-029-68TRANSISTOR DTC114TSA
Q398-729-029-68TRANSISTOR DTC114TSA
Q408-729-900-63TRANSISTOR DTA124ES
Q418-729-900-63TRANSISTOR DTA124ES
Q428-729-012-83TRANSISTOR 2SK679A
Q438-729-012-83TRANSISTOR 2SK679A
Q05A8-729-231-55TRANSISTOR 2SC2878-AB
Q06A8-729-231-55TRANSISTOR 2SC2878-AB

Resistor

Part No.Description
R111-247-855-11CARBON10K 5% 1/4W
R121-247-855-11CARBON10K 5% 1/4W
R131-247-843-11CARBON3.3K 5% 1/4W
R141-247-843-11CARBON3.3K 5% 1/4W
R151-249-431-11CARBON15K 5% 1/4W
R161-249-431-11CARBON15K 5% 1/4W
R171-249-387-11CARBON3.3 5% 1/4W F
R181-247-847-11CARBON4.7K 5% 1/4W
R191-249-390-11CARBON5.6 5% 1/4W F
R201-249-432-11CARBON18K 5% 1/4W
R211-249-432-11CARBON18K 5% 1/4W
R221-249-424-11CARBON3.9K 5% 1/4W F
R231-249-432-11CARBON18K 5% 1/4W
R241-249-420-11CARBON1.8K 5% 1/4W F
R251-247-838-11CARBON2K 5% 1/4W

VR Board

Ref. No.Part No.DescriptionRemarks
*1-672-765-11VR BOARD
VR021-225-749-11RES, VAR, CARBON 50K/50K (REC LEVEL)

Hardware List

Part No.Description
#17-685-534-19SCREW +B 2.6 × 8 (TYPE2)
#37-685-533-19SCREW +B 2.6 × 6 (TYPE2)
#47-685-535-19SCREW +B 2.6 × 10 (TYPE2)
#67-685-547-19SCREW +B 3 × 10 (TYPE2)
#77-682-903-11SCREW +PWH 3 × 6
#87-685-645-79SCREW +P 3 × 6 TYPE2 NON-SLIT
#97-685-146-11SCREW +P 3 × 8 TYPE2 NON-SLIT
#107-685-132-19SCREW +P 2.6 × 5 TYPE2 NON-SLIT
#117-671-157-01BALL, STAINLESS (5 DIA)
#127-627-551-18SCREW,PRECISION +P 1.4 × 2
#137-685-105-19SCREW +P 2 × 8 TYPE2 NON-SLIT
#147-621-772-10SCREW +P 2 × 4

Miscellaneous

Part No.Description
151-773-128-11WIRE (FLAT TYPE) (19 CORE)
631-555-750-00CORD, POWER
651-526-794-11OUTLET, AC
HRPE9013-017-303-01HEAD (REC/PLAY/ERASE)
M9013-017-239-01PULLEY (MOTOR) (LOADING)
M9023-017-259-01PULLEY (MOTOR)(CAPSTAN REEL)
S9013-017-238-01LIMITTER (SW MSS-8B)(OPEN)
S9023-017-238-01LIMITTER (SW MSS-8B)(CLOSE)

Accessories & Packing Materials

Part No.Description
1-790-441-11CABLE, IC CONNECTOR 5P (SYSTEM CABLE)
3-020-441-01BRACKET (PATCH CORD)(AUDIO CABLE)
3-864-773-11MANUAL, INSTRUCTION (ENGLISH)
3-864-773-21MANUAL, INSTRUCTION (FRENCH/SPANISH) (AEP, UK, E, SP)
3-864-773-31MANUAL, INSTRUCTION (GERMAN/DUTCH/SWEDISH/ITALIAN/PORTUGUESE) (AEP, UK)
3-864-773-41MANUAL, INSTRUCTION (CHINESE) (E, HK, SP)
Models: TC-SD1, TC-PX100, TC-SD1-TC-PX100 Stereo Cassette Deck, TC-SD1-TC-PX100, Stereo Cassette Deck, Cassette Deck

File Info : application/pdf, 32 Pages, 12.98MB

PDF preview unavailable. Download the PDF instead.

Sony-TCSD1-tape-sm Acrobat Distiller 3.0 for Power Macintosh

Related Documents

Preview Sony TC-K555ES Stereo Cassette Deck Service Manual
This service manual provides detailed technical information, specifications, safety checks, and troubleshooting guidance for the Sony TC-K555ES Stereo Cassette Deck. It includes block diagrams, function controls, and recommended settings for recording.
Preview Sony TCM-450DV Service Manual
This service manual provides detailed information for the Sony TCM-450DV cassette recorder, including specifications, disassembly instructions, mechanical and electrical adjustments, diagrams, and parts lists.
Preview Sony TCM-200DV/150 Cassette-Corder Operating Instructions
This document provides comprehensive operating instructions for the Sony TCM-200DV and TCM-150 Cassette-Corders. It covers setup, power sources, recording procedures, playback functions, maintenance, troubleshooting, and technical specifications.
Preview Sony CFD-E90 CD Radio Cassette Recorder - Features and Specifications
Comprehensive overview of the Sony CFD-E90 CD Radio Cassette Recorder, detailing its features such as compact design, jog dial, sleep/wake timer, digital AM/FM tuner, CD-R/RW playback, Mega Bass sound system, and synchronized dubbing, along with technical specifications.
Preview Sony TCM-929 Operating Instructions Manual
This manual provides comprehensive operating instructions for the Sony TCM-929 Cassette-Corder. It covers setup, power sources (AC adapter and dry batteries), recording with the built-in or external microphone, playing tapes, troubleshooting common issues, maintenance tips, and detailed specifications. Includes warranty information.
Preview Sony TCM-5000EV Pressman Portable Cassette Recorder: Features and Specifications
Explore the advanced features and technical specifications of the Sony TCM-5000EV Pressman portable cassette recorder, including voice-operated recording, three-head system, and comprehensive controls.
Preview Sony TCM-150 Cassette-Corder Service Manual - Repair and Specifications
Comprehensive service manual for the Sony TCM-150 Cassette-Corder, including detailed specifications, disassembly instructions, electrical and mechanical adjustments, diagrams, and parts lists.
Preview Sony HCD-GNZ55D Service Manual - DVD Deck Receiver
This service manual provides comprehensive technical information for the Sony HCD-GNZ55D DVD Deck Receiver, covering specifications, disassembly procedures, electrical and mechanical adjustments, circuit diagrams, and a detailed parts list for repair and maintenance.