FUTECH Professional measuring tools for construction
User Manual for FUTECH models including: 052.02R Para Red Rotation Laser Level, 052.02R, Para Red Rotation Laser Level, Red Rotation Laser Level, Rotation Laser Level, Laser Level
USER MANUAL 052.02R PARA RED 052.02G PARA GREEN EN ENGLISH Manual in your language? Check the back cover 221205110126
File Info : application/pdf, 16 Pages, 2.20MB
DocumentDocument221205110126 USER MANUAL 052.02R PARA RED 052.02G PARA GREEN EN ENGLISH Manual in your language? Check the back cover OVERVIEW 02 05 04 17 10 01 09 13 14 06 03 11 12 08 07 15 B PARA 16 g J f K b d e D E h c i F G a C L M H I N O P A Q 2 HOUSING 01 Laser head 02 Plumb point up (Z-axis) 03 Keypad 04 X-axis 05 Y-axis 06 Quick guide 07 USB-C Power socket 08 5/8" screw Horizontal mode / Plumb point down (Z-axis) 09 5/8" screw Vertical mode 10 Feet vertical mode 11 LI-ION battery 12 USB-C power socket (bat- tery) 13 Model label 14 Serial number 15 Remote control 16 Window cover piece 17 Metal window cover KEYPAD A Power button B Arrow UP button C Arrow DOWN button D Arrow LEFT button E Arrow RIGHT button F Speed button G Scan button H Slope button I Tilt/Wind button J Turn LEFT button K Turn RIGHT button L LED indicator X-axis M LED indicator Y-axis N LED Slope indicator O LED Tilt/Wind indicator P LED Power indicator Q LEDS Battery indicator REMOTE CONTROL a Power / standby button b Arrow UP button / Turn RIGHT button c Arrow DOWN button / Turn LEFT button d Arrow LEFT button e Arrow RIGHT button f Speed button g Scan button h Slope button i Tilt/Wind button 3 QUICK START GUIDE KEYPAD REMOTE CONTROL NAME FUNCTION A a Power button Switch ON/OFF the device B b Arrow UP button Change the slope. Y-axis rises on the side indicated by the arrow C c Arrow DOWN button Change the slope. Y-axis descends on the side indicated by the arrow D d Arrow LEFT button Horizontal mode Change the slope. X-axis rises on the side indicated by the arrow Vertical mode Move the laser line and dot (z-axis) to the left E e Arrow RIGHT button Horizontal mode Change the slope. X-axis descends on the side indicated by the arrow Vertical mode Move the laser line and dot (z-axis) to the right F f Speed button Change spinning speed 0 60 300 600 800 RPM G g Scan button Use and change scan modus 0° - 10° - 45° - 90° - 180° H h Slope button Switch ON slope modus. (Automatic levelling is switched off) I i Tilt/Wind button Press short Switch ON/OFF Tilt security Hold 3 sec. Switch ON/OFF Wind function J c Turn LEFT button Turn the laser anti clockwise in scan modus or when speed is 0 RPM. K b Turn RIGHT button Turn the laser clockwise in scan modus or when speed is 0 RPM. L / LED indicator X-axis green, continuous Levelled green, flashing Levelling in progress no Levelling not active red, continuous Levelling not active, a slope was selected. 4 KEYPAD REMOTE CONTROL NAME FUNCTION M / LED indicator Y-axis green, continuous Levelled green, flashing Levelling in progress no Levelling not active red, continuous Levelling not active, a slope was selected. N / LED Slope indicator No Slope modus OFF Red, continuous Slope modus ON Red, flashing Laser out of levelling range O / LED Tilt/Wind indicator No Tilt security & Wind modus OFF Green, continuous Wind modus active Red, flashing slow Preparing TILT security Red, continuous TILT security active Red, flashing fast TILT alarm P / LED Power indicator Green, continuous Power ON No Power OFF Q / LED Battery indicator 4x green >80% battery charge 3x green >60% battery charge 2x green >40% battery charge 1x green >10% battery charge 1x red <10% battery charge 5 SAFETY AUTOMATIC FUNCTIONS Please read the safety instructions provided as separate booklet with the device. LASER RADIATION Class 2 Laser product. Do not stare into beam FIRST TIME USAGE Remove all protection foils. Place the provided LI-ION battery in the device. Make sure the batteries are fully charged. The four LEDs of the battery indicator light up green. Place 2x AA Alkaline batteries in the remote control. BATTERY AND CHARGER Laser: This laser works with a 3.7V - 8000mAh LI-ION battery. To charge this battery, you can use the provided 12V - 3A charger for fast charging. Remote control: The remote control works with 2x 1.5V AA Alkaline batteries. AUTO-LEVELLING This rotation laser first levels itself automatically after turning on the device. After being levelled, the laser starts spinning. The laser can level itself within an operating angle of approx. 5°. The auto-levelling system performs the necessary fine adjustments, with the help of 3 electronic measuring sensors, one for each axis (X, Y and Z). TILT SECURITY The tilt-security avoids measuring errors. By default, the laser will be active with the tilt-security activated. After turning on the laser or after activating the tilt-security, the tilt-security is prepared during 60 seconds. During this time you can install the laser in the sorrect position. 60 seconds after you hit the last button, the tilt-security is active. When the tilt-security sensors detect a small shock (e.g. a vibration, a gust of wind, ...) the laser will stop turning and starts flashing and beeping. This give you the opportunity to check if the laser is still in the correct position after the shock. You must exit the tilt function, place the laser in position and restart the laser to continue. A new preparation process of approx. 60 seconds will 6 start before the Tilt-security is active. Tilt-security is the best choice if accuracy is the most important. BASIC MODE (TILT-SECURITY AND WIND FUNCTION OFF) In the basic mode the laser will stop spinning if the sensors detect a slight shock, such as a vibration or gust of wind. The laser will re-level automatically and start spinning again when it is levelled again. This function is a compromise between accuracy and efficiency. USE Press the power button [A] to activate the device. NOTE The choice of the tripod defines in a large way the user-friendliness of the device. If the workplace has a high light intensity, for example when working outside in a sunny area, you will need a laser receiver to detect the laser beam. HORIZONTAL ALIGNMENT WIND FUNCTION The wind function is often used when you need to work on a vibrating surface, or in windy conditions. Also, when quick levelling is needed. The laser doesn't stop spinning when the wind function is active, even if the sensors detect slight shocks. The levelling takes place while the laser is spinning. You can continue to work. IMPORTANT Keep in mind that this is the least accurate method of working. Measurement errors can occur. After turning on the device, the laser light blinks without spinning. The LED indicators X-axis [L] and Y-axis [M] blink green during levelling. When levelled, the laser beam and the LED indicators X-axis [L] and Y-axis [M] will light continuously and the laser will start spinning at 600 rotations per minute, the optimal speed for usage with a receiver. 7 By default, the Tilt security will prepare after turning on the device. NOTE The device should not be placed on a surface with a slope of more than 5°. If this is the case, the laser is outside the self-levelling range, in which case the laser diode will continue to blink and the LED indicator slope [N] will flash red. VERTICAL ALIGNMENT PLUMB LINE Thanks to the plumb line, which are projected via Plumb point up [02] and Plumb point down [08], this device can also be used to bring a plumb lead point of the floor to the ceiling, or visa versa. · Mark the starting point. · Place the laser beam exactly on this starting point · Now you can mark the opposite plumb point accordingly. Put the device on its feet vertical mode [10] for vertical alignment (keypad should be at the top). The LED indicator Y-axis [M] will blink during levelling. When levelled, the laser beam and the LED indicator Y-axis [M] will light continuously and the laser will start spinning at 600 rotations per minute, the optimal speed for usage with a receiver. NOTE The device should not be placed on a surface with a slope of more than 5°. If this is the case, the laser is outside the levelling range, in which case the laser diode will continue to blink and the LED indicator slope [N] will flash red. 8 POSITIONING THE VERTICAL LASER LINE In vertical alignment mode, the laser can be positioned exactly. The laser will continue to level while positioning the vertical laser line. · Use the arrow LEFT button [D, d] or arrow RIGHT button [E, e] to move the vertical laser line. above the starting point, the place where the corner of 90° is made. It can be helpful to change the spinning speed to zero when positioning the laser above the starting point. · Bring the rotating laser beam with the help of the arrow LEFT button [D, d] or arrow RIGHT button [E, e] to your first mark. · The Plumb point up [02] (and Plumb point down [02]) show each a corner of 90° with the rotating laser line. SPINNING SPEED CORNERS OF 90° 90° 0 RPM 60 RPM 300 RPM 600 RPM 800 RPM In vertical position, it is possible to project corners of 90°. · Place the laser head [01] as precise as possible This device has multiple speeds spinning. 0, 60, 300, 600 and 800 RPM (rotations per minute). The default rotation speed is 600 RPM. · Press the speed button [F, f] to select the desired speed. Each time you press this button, the speed will change. 600 - 800 - 0 - 60 - 300 - 600 - 800 - ... 9 A speed of 0 RPM projects a stationary laser point. This can be positioned exactly at the measuring point with the turn LEFT button [J, c] or turn RIGHT button [K, b] button. NOTE The slower the rotational speed, the better the visibility with the human eye. A faster rotation speed is necessary to use a laser receiver (600 RPM recommended for handheld receivers, 800 RPM recommended for machine receiver) SCAN FUNCTION 0 ° 10° 45° 90° 180° · Press the scan button [G, g] to select the desired angle of the scan function. Each time you press this button, the angle will change. 0° - 10° - 45° - 90° - 180° - 0° - 10° - ... You can move the position of the light intensive segment by pressing the turn LEFT button [J, c] or turn RIGHT button [K, b] button. SLOPE FUNCTION Standard, the instrument shows a 100% horizontal or vertical laser beam. When needed, the laser can project a sloped laser beam. To set up slopes, you must take a few steps in the right order. NOTE Keep in mind that auto-levelling is disabled when working with the slope function. The LED indicator X-axis [L] and LED indicator Y-axis [M] will switch from green to red to warn you auto-levelling is not active. The scan function allows to limit the laser beam to an angle instead of the complete 360° circle. This creates a light intensive segment that increase the visibility for the human eye. Possible angles of the scan function are 0°, 10°, 45°, 90° and 180°. 10 HORIZONTAL SLOPE, <5° · Next, you position the receiver at the desired slope. (e.g. 2% slope on 10m = height difference of 20cm up or down) < 5° X- and Y-axis · Place the laser in its horizontal (normal) position. · Position the x-axis [04] and y-axis [05] of the laser device (shown on the metal window cover [17]) exactly in the parallel with the direction of the slope(s) you want to make. · Turn on the device and wait until it is levelled (LED indicator X-axis [L] and LED indicator Y-axis [M] are solid green). · Search the zero level of the receiver with the laser beam using OR the arrow UP [B, b] or DOWN [C, c] button (for a slope on the Y-axis) OR the arrow LEFT [D, d] / RIGHT [E,e] button (for a slope on the X-axis) The LED-indicator X-axis [L] turns red after you selected a slope on the X-axis. The LED-indicator Y-axis [M] turns red after you selected a slope on the Y-axis. · Your laser is set with the desired slope. VERTICAL SLOPE, <5° · Choose a distance in the direction of the slope that needs to be set up. (e.g. 10m) · Place the receiver by means of the measuring rod holder on a measuring rod and slide the receiver until the laser beam is at the zero level of the receiver. · Activate the Slope function with the slope button [H]. (LED slope indicator [N] turns red, LED indicator X-axis [L] and LED indicator Y-axis [M] turns off). < 5° Y-axis · Place the laser in its vertical position (on the feet vertical mode[10]). · Turn on the device and wait until it is levelled (LED indicator X-axis [L] and LED indicator Y-axis [M] are solid green). 11 · Activate the Slope function with the slope button [H]. (LED slope indicator [N], LED indicator X-axis [L] and LED indicator Y-axis [M] are solid red). · Use the arrow UP [B, b] or DOWN [C, c] button to set a slope on the vertical line. (If you want, you can reposition the vertical line using the arrow LEFT [D, d] or RIGHT [E, e] button.) · Your laser is set with the desired slope. HORIZONTAL SLOPE, >5° Steeper slopes, slopes outside the laser leveling range, can be set using a slope adapter, which is available as optional accessory. parallel with the slope line you like to make. · Turn on the device and wait until it is levelled (LED indicator X-axis [L] and LED indicator Y-axis [M] are solid green). · Activate the Slope function with the slope button [H]. (LED slope indicator [N], LED indicator X-axis [L] and LED indicator Y-axis [M] turns off). · Set the slope adapter in the desired slope. (Percentage of slope is normally marked on the slope adapter) · Your laser is set with the desired slope. ANTI-REFLECTION > 5° In some cases, unwanted reflections may occur In case you use this slope adapter: while using a laser, for example when the laser beam shines on glass. This can lead to inaccurate · Place the laser in its horizontal (normal) position measurement results and affect the proper on the slope adapter. Make sure the slope functioning of the laser receiver. adapter is at is 0% position. It is possible to shield part of the laser beam · Position the laser in the correct axis-direction, along the side where the reflection may occur. To 12 do this, use the supplied laser cover pieces [16] by sliding them into the metal window cover [17]. Simply remove this laser cover piece [16] when covering is no longer needed. 13 SPECIFICATIONS Visibility Precision Range (with receiver) Dust- and water resistance Levelling Plumb bob Rotations per minute Scan function Wind function Tilt security Self-levelling range Slope function Maximum settable slope (X- and Y-axis) Remote control Built-in screw (for tripod) AC power connector Battery AC power adapter (charger) Laser D x W x H device Weight (with battery placed) 14 052.02R PARA RED 052.02G PARA GREEN 1mm / 10m 2x ± 300m IP66 Motorised 0, 60, 300, 600, 800 0°, 10°, 45°, 90°, 180° ± 5° Manually, Electronic ± 5° 5/8" (horizontal mode) - 5/8" (vertical mode) USB-C LI-ION Class 2, 635nm, <1mW max. output Class 2, 515nm, <1mW max. output (downpoint: Class 2, 650nm, <1mW) (downpoint: Class 2, 650nm, <1mW) 220 x 220 x 218 mm 2,76 kg NOTES 15 USER MANUAL other languages: DA DANSK DE DEUTSCH ES ESPAÑOL ET EESTI KEEL FI SUOMEN KIELI FR FRANÇAIS IS ÍSLENSKA Facebook @futechtools LinkedIn futechtools World Wide Web futech-tools.com YouTube @futechtools IT ITALIANO NL NEDERLANDS NO NORSK PT PORTUGUÊS SL SLOVENSCINA SV SVENSKA 221205110126