User Manual

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended.

FCC ID: 2AZVSA321B

Warning

• To reduce the risk of electric shock, the device has a polarized plug (one flat is wider than the other). A polarized plug will have only one orientation in a polarized receptacle. If the plug does not fit fully into the outlet, turn the plug upside down; if still not, contact a qualified person to install a suitable outlet. Do not alter the plug in any way (American Standard).
• If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person to avoid a hazard.
• This device contains UV emitters. Do not stare at the light source. This device contains a UV-C emitter.
• Do not operate appliances that are visibly damaged.
• Use the device only within the living space and within the stated technical data. Improper use can put health and life at risk.
• Children cannot recognize the dangers of using electronic devices. Therefore, be sure to supervise children when they are near a running device.
• When operating the equipment, use only the original parts provided. Use this device only at room temperature (>10°C).
• Persons unfamiliar with the instructions for use, as well as children and persons under the influence of drugs, alcohol, or medication, should not operate this machine, or operate this equipment only under supervision.
• Do not use the device if the power cord is defective, or if the device has been damaged (e.g., dropped).
• Equipment can only be put into operation in a fully assembled state.
• Do not pull the power cord or unplug the power plug from the power outlet with wet hands.
• Place the device on a level, dry floor.
• Do not operate equipment that is visibly damaged.
• Do not immerse the device in water or other liquids.
• Place the appliance in a place where it cannot be knocked over.
• Please unplug the power plug when cleaning, maintenance, or equipment servicing.
• Do not cover the cables with carpets or other objects. Position the unit so that the cables do not trip over others.
• Do not operate the equipment in rooms containing flammable substances, gases, or vapors.
• Do not leave the appliance in the rain and do not use it in a damp room.
• The power cord must not get stuck in the door or crushed by other heavy objects! Do not move the device during operation.
• Children 8 years of age and older, and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge may use this device if they have been supervised or instructed in the safe use of this device and understand the hazards involved. Little children should not operate this equipment. Children should not clean and maintain this equipment without supervision.
• If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Adjust the direction or position of the receiving antenna.
• Increase the distance between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Regulatory Information

• This device contains a license-exempt transmitter/receiver that complies with the Innovation, Science and Economic Development Canada license-exempt RSS standard. The operation is subject to the following two conditions:
• This device may not cause interference.
• This device must accept any interference, including interference that may cause undesired operation of the device.
• This device complies with FCC and IC RF radiation exposure limits set forth for an uncontrolled environment. Antennas for Tsai transmitters must be installed and operated so that everyone is kept at least 20 cm apart and cannot be installed or operated in conjunction with any other antennas or transmitters. The installer people must ensure that a 20cm separation distance is maintained between the device (excluding the mobile phone) and the user.
• Persons (including children) with reduced physical, sensory, or mental capabilities or lack of experience and knowledge should not use this equipment unless their use of this product has been supervised or instructed by those responsible for their safety. Supervise children to ensure they do not operate this machine.
• WARNING: The user is not allowed to replace the UV-C emitter. If the UV-C emitter cannot be replaced, it must be clearly stated.
• Failure to use the device as intended or damage to the housing may result in the escape of dangerous UV-C radiation. Even in small doses, UV-C radiation can cause damage to the eyes and skin. Make sure the device is disconnected from the mains power supply before removing the protective cover.
• This product complies with the maximum allowable concentration of ozone of 0.050ppm, parts per million by volume (ppmv) in a 24-hour period. The Health Canada Guideline 2010 recommends that the maximum exposure limit, based on an averaging time of 8 hours, is 0.020 ppmv or less when tested in a sealed, controlled room approximately 30 m³.
• (French text regarding ozone compliance: Ce produit est conforme avec la concentration maximale premise d'ozone de 0,050 parties par million par volume (ppmv) pendant une période de 24 heures. La Ligne directrice (2010) de Santé Canada recommande un niveau maximal d'exposition, basé sur un moyen de 8 heures, soit 0,020 ppmv ou moins dans une chambre de teste étanchée et contrôlée de 30 m³.)
• UV radiation is dangerous to eyes and skin. Do not operate the UV C emitter outside the device.
• ELECTRIC SHOCK HAZARD - THESE SERVICE INSTRUCTIONS ARE FOR QUALIFIED PERSONNEL ONLY. To reduce the risk of electric shock, do not perform any repairs excepting those described in the operating instructions unless you are electronics qualified.

Important Placement and Usage Guidelines

• Disconnect power before repairing.
• Do not place in such places:
• Unstable places. (Otherwise, it may fall over and cause injury)
• A place of high temperature, high humidity, or easy to get wet. (to prevent leakage accidents)
• Kitchen or other places where soot is emitted.
• A place with lots of oil, combustible gases, or where leakage may occur.
• Corrosive gas and metal dust sites.
• Do not let volatile substances or combustible substances into the machine. (Otherwise, it could lead to a fire accident)
• Do not use the air purifier in a room with fumigated insecticide. (The chemical residue accumulates inside the machine and may be released from the outlet and endanger health)

1. Product description

This air purifier can strongly remove smoke and dust, and is suitable for places with more smoke, dust, pollen, particles, and pollutants in the air, such as indoor smoking. This can reduce the chance of you and your family being harmed by second-hand smoke and haze, and can protect your health.

This air purifier is equipped with a composite filter which can effectively remove particles in the air, including particles of PM2.5 level, formaldehyde, and odor (smoke), making the air you breathe clean and fresh.

Composite filter: This filter can absorb smoke, pollen, and dust, intercept bacteria in the air, effectively remove TVOC, odor (smoke) in the air, deeply clean the air, and effectively remove PM2.5.

2. Packing list

3. Instructions for use

3.1 Precautions for filter

All filters are attached to the inside of the air purifier. Before using the product, be sure to remove the packaging of the filter. Please follow the procedure in the following diagrams to take out all filters from the host and remove their packaging, and then put filters back into the air purifier.

1. Pre-filter

2. HEPA activated carbon composite filter

Special Note: The filter with activated carbon may potentially produce a small amount of powder due to rub. This powder may adhere to other filters but will not affect the function of the product; please use it with peace of mind.

Attention:

• Before using the product for the first time, be sure to remove the packaging of the filter.
• Make sure the user replaces the filters in the right order (from inside to outside): HEPA activated carbon composite filter and pre-filter.
• Make sure the filter assembly is attached into the machine in the right direction.

Hint:

• When taking out or attaching the filter, the air-purifier can be rested on a support to enhance stability.
• This product should be placed on a stable ground to prevent the machine from falling down and causing unnecessary malfunction.

3.2 Steps to attach the filter

1. Place fingers on the buttons on the left and right sides of the machine. Press the buttons, and the front cover will automatically open. [Diagram: Shows hands pressing buttons on the sides of the air purifier to open the front cover.]
2. Open the front cover towards your direction. [Diagram: Shows the front cover being opened outwards.]
3. Remove all filters from the air-purifier. [Diagram: Shows hands pulling out filters from the opened air purifier.]
4. Remove all packaging from the filter. [Diagram: Shows hands peeling off plastic packaging from a filter.]
5. Assemble the entire set of filters into the air-purifier in the right order. [Diagram: Shows filters being inserted into the air purifier, with an arrow indicating the 'Handle' side of the HEPA filter.] Attention: Make sure that the HEPA activated carbon composite filter with the handle is facing towards you, and ensure all hooks of the filter are properly fitted to the air purifier.
6. Firstly, fit the hook at the bottom of the front cover to the bottom of the air purifier, then push it towards the body of the purifier and fasten it. [Diagram: Shows the bottom hooks of the front cover being aligned with slots on the air purifier body before being pushed and secured.]

4. UI operation menu

The control panel features various buttons and indicator lights for operating the air purifier.

4.1 Power

1. Connecting the power: The power button ? [Power] will light up.
2. Press the button to operate the machine. You will hear a "ding" sound once the operation is successful.

4.2 Mode

1. Touch to adjust the fan speed, or switch to Do Not Disturb or Auto mode. You will hear a "ding" sound each time you touch the button.
2. When you press and hold the Mode button for 3 seconds until you hear a 'Ding' sound, you will start the breath-hold mode, where the panel lights are all turned off. To turn the lights back on, please press and hold the Mode button again for 3 seconds until you hear a "ding" sound.

4.3 Timer

1. Press the Timer key ⏱️ [Timer] multiple times to set the timer for 1/2/4/8 hours sequentially. When the Timer key light is on and the 4 indicator lights at the bottom are also lit, there will be a 'ding' sound.
2. Press and hold the Timer key ⏱️ [Timer] for 3 seconds. The Timer key light will turn off, and all 4 indicator lights at the bottom will also turn off, indicating the timer is turned off. You will hear a 'ding' sound.

4.4.1 UV-C

1. Turn on UV-C or Anions (Only for breeva Pro 400 premium): Press the UV-C/Filter button ? [Filter] once. The button light will turn on, you will hear a 'ding', and UV-C or Anions will activate. (Note: UV-C or Anions can only be turned on separately via the APP; the machine button can only turn UV-C on or off at the same time).
2. Turn off UV-C or Anions (only for breeva Pro 400 premium): Press the UV-C/Filter button ? [Filter] once. The button light will turn off, you will hear a 'ding', and UV-C or Anions will deactivate. (When UV-C or Anions are both turned on, UV-C can be turned off individually by APP. If only one function is turned off, the light will not turn off).

4.4.2 Anions

1. Turn on Anions (Only for breeva Pro 400): Press the Anion button ✨ [Anion] once. The button light will turn on, you will hear a 'ding', and Anions will activate. (Note: The APP can only turn Anions on, but the machine button can both turn Anions on or off).
2. Turn off Anions (only for breeva Pro 400): Press the Anion button ✨ [Anion] once. The button light will turn off, you will hear a 'ding', and Anions will deactivate. (When Anions is turned on, Anions can be turned off by APP. If only one function is turned off, the light will not turn off).

4.5 Filter

1. Filter life:
   • When the light is white, it means the filter life is sufficient.
   • When the light is yellow, it means the filter life is less than 5%.
   • When the light is red, it means the filter life is exhausted; please replace the filter as soon as possible.
2. To reset the filter life: Press and hold the Filter button ? [Filter] for 3 seconds. You will hear a 'ding' to confirm the reset.

4.6 AQI indicator

1. By reading the values from the dust sensor and VOC sensor, the current air quality is determined and displayed through three-color LED lights.
• When the light color is white, it means the air quality is excellent.
• When the light color is yellow, it means the air quality is medium.
• When the light color is red, it means the air quality is poor.
2. Note: AQI is an indicator light without actual function. The AQI standard adopts the US EPA recommended value.

4.7 Lock button

1. To enable panel lock: Press and hold the Lock button ? [Lock] key. You will hear a "ding" to turn it on. When the panel is locked, touching any key will cause the Lock key to flash twice.
2. To turn off panel lock: Long press the Lock button ? [Lock] key. You will hear a 'ding' to turn it off.

5. How to clean air-purifier

Note:

• Always unplug the power plug before cleaning the purifier. Never place the purifier into water or any other liquid.
• Never use abrasive, caustic, or flammable cleaners (such as bleach or alcohol) to clean any part of the purifier.
• Only the pre-filter can be washed with water. Other filters cannot be washed with water or cleaned by other cleaners; they should only be replaced directly.

5.1 Exterior cleaning

Regularly clean the inside and outside of the air purifier to prevent dust from accumulating.

1. Use a soft dry cloth to wipe the dust off from the body of the air-purifier.
2. Clean the air inlet and air outlet with a soft dry cloth.
3. It is forbidden to wipe the body of the air-purifier with a wet cloth with water to prevent liquid from entering the machine and causing malfunction.

5.2 Cleaning the dust sensor cover

Clean the dust sensor cover every 2 months to ensure the air-purifier is running at its best performance. If the air-purifier is used in a dusty environment, clean it frequently.

Note:

• When the room is highly humid, condensation may form on the dust sensor. At this time, even if the air quality is good, the air quality indicator may show red, leading to a misjudgment that the air quality is poor. In this case, please clean the dust sensor.
• When TVOC is higher than 3mg/m³, it should be avoided to stay in this environment for more than 1 month. The test results of TVOC equipment produced by different working principles or different manufacturers may vary.
• If TVOC readings are abnormal, place the device away from volatile substances for 24 hours and allow the TVOC to reset.

1. Use a soft brush ?️ [Brush] to clean the dust sensor air inlet/outlet. [Diagram: Shows a soft brush cleaning the dust sensor area.]
2. Remove the protective cover of the dust sensor. [Diagram: Shows a hand carefully removing a small cover near the dust sensor.]
3. Using a slightly wet cotton swab ☁️ [Cotton Swab] to clean the dust sensor air inlet and air outlet; then dry it with a dry cotton swab. [Diagram: Shows a cotton swab cleaning the dust sensor area.]

6. How to clean the filter

Note:

• Only the pre-filter can be washed with water.
• It is recommended to clean the pre-filter every 30 days to ensure the air-purifier is running under the best performance.

1. Please turn off the air-purifier and unplug the power ? [Plug]. [Diagram: Shows a hand unplugging the power cord.]
2. Place fingers on the buttons on the left and right sides of the machine. Press the buttons, and the front cover will automatically open. [Diagram: Shows hands pressing buttons on the sides of the air purifier to open the front cover.]
3. To remove the pre-filter, take the top two flanges and pull the filter out towards you. [Diagram: Shows hands gripping the top flanges of the pre-filter and pulling it out.]
4. Rinse the pre-filter under the tap. If it is too dirty, please use a soft brush ?️ [Brush] to remove dust from it. [Diagram: Shows the pre-filter being rinsed under a faucet, with a brush nearby.]
5. Dry the pre-filter with air. [Diagram: Shows hands holding the pre-filter, with water droplets falling, indicating drying.]
6. Put the pre-filter back inside the purifier. Then properly assemble all hooks to the purifier. [Diagram: Shows the pre-filter being reinserted into the air purifier, aligning hooks.]
7. To install the front cover, firstly assemble the bottom hooks to the bottom of the air-purifier, and then push the front cover towards the air-purifier body. [Diagram: Shows the front cover being attached by aligning bottom hooks and pushing it closed.]

7. Replace the filter

When it is necessary to replace the pre-filter and HEPA activated carbon composite filter, please follow the steps below to correctly replace the new filter.

Attention:

• Activated carbon filter and HEPA filter are not washable or vacuumable by cleaner.
• Make sure that the order you assemble the filter is: HEPA activated carbon composite filter, then pre-filter.
• Make sure the filter assembly is attached in the machine in the correct way.

1. Please turn off the air-purifier and unplug the power ? [Plug]. [Diagram: Shows a hand unplugging the power cord.]
2. Place your fingers at the grooves on both sides of the top of the filter cover and gently pull out the first half of the filter cover, then lift the filter cover upwards. [Diagram: Shows hands gripping the top of the filter cover and pulling it open.]
3. Remove all filters inside the purifier. [Diagram: Shows hands pulling out filters from the opened air purifier.]
4. Remove all packaging from the filter. [Diagram: Shows hands peeling off plastic packaging from a filter.]
5. The order of replacing new filters (inside to outside) is: HEPA Activated Carbon Composite filter, pre-filter. [Diagram: Shows new filters being inserted into the air purifier in the correct order.] Attention: Make sure the side with the two flanges is facing towards you and all hooks of the pre-filter are properly fitted to the air-purifier.
6. Before installing the filter cover, assemble the bottom hooks to the bottom of the purifier. Then push the filter cover towards the purifier body. [Diagram: Shows the front cover being attached by aligning bottom hooks and pushing it closed.]

8. APP Networking Instructions

1. Download the app

You can scan the QR code below through other software to download TCL HOME or search for "TCL HOME" in the APP Store and Google Play store to download and install it. [Description: A QR code placeholder for app download.]

2. Configuration settings

Under the standby state, press and hold the power button ? [Power] for 3 seconds. The buzzer will sound, the Wi-Fi indicator ? [Wi-Fi] will flash quickly, and the device will enter the configurable state. When the Wi-Fi indicator is constantly on, the configuration is complete.

Use the TCL HOME APP to operate the device. After that, you can observe whether the air quality in your home is within the target range in real time through the TCL HOME APP. TCL HOME APP can also help you to control the device to purify the air in your home.

Hint: If your connection fails, check this list:

• A. Please reset the device properly and try again.
• B. Confirm that you have turned on Bluetooth and WiFi, and WiFi is connected to the network.
• C. Keep your phone as close to the device as possible.
• D. Ensure your phone is not in power saving mode.

3. Voice operation

After the configuration is complete, please go to the center page and click on the voice assistant to enter the voice operation settings:

• A. Press the function to start connecting to the voice assistant.
• B. TCL HOME APP configures both ALEXA and Google voice assistants; you can choose your favorite voice assistant.
• C. The voice operation guidelines will be showing.

Tips:

• A. Due to APP updates, the actual operation may be slightly different from the above description. Please follow the major instructions of the current APP to operate.
• B. Wi-Fi wireless connection devices only support 2.4GHz networks, not 5GHz networks.
• C. Turn off Wi-Fi mode: Long press the power button ? [Power] for more than 3 seconds. The device will return to network mode. At this point, press the power button again; the device will turn off the network mode, and the device will also be turned off.

Note: If Wi-Fi is connected, pressing the power button once turns off the device. If Wi-Fi is not turned off, the Wi-Fi mark will stay on and its brightness will decrease to 50%. If the Wi-Fi has been disconnected, you can reconfigure the connection by following the steps in "Turn on the Wi-Fi function".

9. Types of malfunctions and solutions

This chapter summarizes the most common problems you may encounter when using your air-purifier. If you are unable to resolve the issue based on the information below, please contact the store where you purchased it or the customer service center.

10. Product Specifications

11. Name for each parts

[Diagram: An exploded view showing the parts of the air purifier.]

• 1. Front cover
• 2. Pre-filter
• 3. HEPA activated carbon composite filter
• 4. Host
• 5. Air outlet
• 6. Control panel
• 7. Air inlet