User Guide for thingsys models including: G17H Vehicle Positioning Terminal, G17H, Vehicle Positioning Terminal, Positioning Terminal, Terminal
Index of /images
card installation: install the SIM card in the correct direction when the external power is not connected. After fastening the SIM card, turn the switch to 0n, and then cover the surface. card retrieval: disconnect the external power and turn the switch to 0ff before removing the SIM card. Remarks: The SIM card needs to be enabled with data traffic, SIM and voice functions. 2 Close the upper cover Installation instructions The terminal shall be installed in a concealed manner. It is recommended that a professional organization designated by the dealer install the terminal. Installation precautions: Concealed installation, pay attention to waterproof. Please turn on the device terminal battery switch before use.During installation, ensure that (indicator light) is upward and there is no metal shield above. It can be fixed with tie or sponge double-sided adhesive tape. the external power equipment starts automatically, and the power indicator (red) is always on use the backup battery independently without external power, and the power indicator (red) flashes slowly search network signal (yellow indicator) and GPS signal (blue indicator )flash quickly after normal operation, the network signal (yellow indicator) and GPS signal (blue indicator) flash slowly SOS alarm:long press sos for 3 seconds, the device dials the SOS number, and the other party can realize the listening function after answering. Please use the battery specified by the original manufacturer of your terminal. Using any other accessories will invalidate all warranty services. If the terminal is damaged due to the use of non original accessories, the manufacturer will not bear any warranty liability. Do not let metal objects cause short circuit of battery contactor Do not bend or forcibly open the battery Do not immerse the battery in water or put it on fire The battery must be charged near room temperature, if the temperature is low 0 or above 45, the battery may not work It is forbidden to use batteries with deformed appearance, discoloration, liquid leakage or damaged outer packaging It is forbidden to disassemble and transform the battery If you feel abnormal when operating the terminal, please refer to the following problems and solutions. If you cannot solve the problem, please contact the seller or service provider. Common problem Poor signal reception Problems arose Terms of settlement When terminals are used in areas with poor reception, such Use the terminal as near high-rise at a good signal buildings or basements, radio waves cannot be position effectively transmitted SIM card not installed properly Check SIM card Dirt on metal surface Wipe with a clean of SIM card Unable to connect cloth to the network Please move to the Out of GSM service network service area provider service area Weak signal Please move to a place with strong signal and try again SIM card is not enabled with GPRS Location information function not found Please contact the network service provider to activate GPRS function. Always reply "failed Please contact to get location" your dealer Vehicle positioning terminal Safe use guide G17H&G17S Please read the installation and use guide carefully before use to install correctly.If there is any change in the appearance of the product, please refer to the real object! ACC detection Electronic fence Low power alarm Track playback Real time positioning Electronic fortification Displacement alarm SOS Alarm Cut off oil and power Thread trimming alarm Vibration alarm MIC Positive Back Red Black Orange Yellow MIC Note: the product is divided into 4-wire and 8-wire. Mic and SOS keys are optional and can be selected according to customer needs. Definition of terminal outgoing line state meaning Red Black Orange Connected to positive pole (9-90VDC) Connected to negative pole Connected to on position of ACC Yellow Connected to relay or lock motor Red LED (power / working status) state meaning Slow flash Long bright Not on Normal operation (battery powered) Normal operation (connected to power supply) Device failure or hibernation Yellow LED (GSM signal light) state meaning Flash Slow flash Not on Network initialization Network receiving signal is normal No network signal found or sleep Blue LED (GPS signal light) state meaning Flash GPS signal searching Slow flash GPS signal reception is normal Not on No GPS signal found or sleep 3.5WiFi assisted positioning relay Male female Red (positive) Black (negative) red line Orange Line 87A and 87 cut the speed regulating wires short and connect them respectively Yellow (relay) Key switch Orange (ACC) Connection method Connecting the lock motor Connecting the relay Speed control handle ground wire Red (positive) controller The red positive pole is connected to the battery positive pole (+), and the black negative pole is connected to the battery negative pole (-). The power input line interface is connected to the positive and negative pole interface of the power supply (the positive and negative poles cannot be reversed) ACC line connected to ACC line on vehicle Yellow wire connected relay cuts off oil power or locks motor Oil and electricity disconnection wiring method 1: (1) Find out the "speed control handle control line". The method: "speed control handle control line" is generally green or white, on the 4Pin connector of the controller. (2) Measure the voltage of the speed control handle line with a multimeter. The voltage of the control line of the speed control handle is 0.8V by default (in the static positive state when ACC is on). When the speed control handle is adjusted to the highest speed, it is about 4.3v-5v. (3) Change the speed control line into 2 lines. (4)Connect the two lines of the cut speed control line to the two lines of the normally closed end of the relay. Remarks: the oil and electricity cut-off function must be equipped with a relay specified by the manufacturer (it is recommended that electric vehicles use a 5V relay specified by the manufacturer, and automobiles use a 12V relay specified by the manufacturer) Lock motor wiring method 2: Adjust the multimeter to the DC voltage of 200V, connect the black pen to the negative pole of the battery, and the red pen to the controller line one by one. If the voltage is displayed as a line of 3~5v, it is judged to be a locked motor line, which can be connected with the yellow line. Login location service platform Please log in to the service platform designated by the dealer for corresponding settings and function operations. Default login account: IMEI number (see sticker) default login password: 123456 Downloading Mobile Application Please log in to the website designated by the dealer to download the mobile applicationsoftware for installation. IOS Android 5.3SMS command operation 1 Status query Format: Status# 2 Set SOS number Format: SOS, a, number# 3 Address query Format DW or 123 Open InsertAdobe Illustrator 24.2 (Windows) GPL Ghostscript 10.00.0