SZ10-ZN/EN-A06. 中文P19. 2. The foam should contain: two filament guide tubes, one SD card, two pieces of build tape, one Flashforge leveling card, one After-sales service, one Quick Start Guide and...
SZ10-ZN/EN-A06 P19 2. The foam should contain: two filament guide tubes, one SD card, two pieces of build tape, one Flashforge leveling card, one After-sales service, one Quick Start Guide and one User Guide. 3. Firmly grasp the two sides handles of Flashforge Creator Pro. Lift it out from the carton and place it on a stable surface. 01 7. Remove the foam container. It should contain: a power cable, an USB cable, two spool holders, a tool bag and an extruder's accessory kit. 8. Shear three ties off on both sides of X-axis guide rod. 9. Slide the X-axis Rods to the very back. 10. Open the door, remove top lid of the printer, take filament out of the lid. 11. Find plastic board sealed with "Flashforge" at the back of build plate, take out the foam blocks at the back of plastic board. 02 12. Remove side foam. 13. Take power cable out and plug it into power input. FF Creator Pro Print from SD Preheat Utilities 14. Plug the other end of power cable into socket, 15. Operating on the LCD panel, press downwards turn on the power switch. arrow to choose [Utilities], tap [Ok]. Monitor Filament Loading Preheat Settings General Settings Level Build Plate Home Axes Bot Statistics Filament Odometer 16. Press downwards arrow, enter the next page. 17. Press downwards arrow, enter the next page. Profiles Home offsets Toolhead offsets Jog Mode 18. Choose [Jog Mode], tap [OK]. Jog Mode X+ (Menu) Y- X- 19. Tap rightwards arrow to the next page. 03 Jog Mode Y+ -X (Menu) ZY- 20. Tap rightwards arrow to the next page. 22. Remove foam under build plate. Jog Mode Z-Y (Menu) Z+ 21. Pess upwards arrow, the build plate goes up until it comes to the highest position, loose the button when the printer stops. Jog Mode Z-Y (Menu) Z+ 23. Press down arrow, loosen the button when the build plate descends to the middle of the printer. Tap [Ok], go back. FF Creator Pro Print from SD Preheat Utilities 24. Tap [Ok], go back, tap leftwards arrow twice, 24. Unboxing completed! Recommended that you go back to the Home screen. take good care of packing materials for furthur carrying and keeping. 04 User Guide Filament Guidetube x2 Build Tape x 2 Tool bag: Allen Wrench*2 / Knob / M3x8 Bolt*2 / PTFE Tube*2 / Grease / Unclogging Pin Tool / Wrench Extruder's accessory: M3x8 Bolt*2 / M3x6 Bolt / Turbofan Baffle 05 6. Platform Support 3. Lid Slot 7. Knob 23. USB Cable Input 06 1. Place the dual extruder on the extruder seat. 2. Take the M2.5 Allen Wrench from the tool bag and two M3x8 bolts from the accessory kit. 3. Adjust the extruder location to align the bolt holes. 4. Secure the extruder onto the extruder seat by screwing the M3x8 bolts in. 07 08 09 3. Take filament out and remove vacuum packing, squeeze both sides on the top of spool holder and mount filament spool to the holder. 10 Filament installation tips The filament spool must be oriented correctly ( see below ). Correct Installation Wrong Installation Filament Guidetube Buckle Limited seat 4. Install PLA filament on the right side of the printer, and put filament through filament guidetube. 5. Lock filament guide tube into fixed buckles, and guidetube bottom should not be over limited seat. 11 Press here Filament intake 6. After filament guidetube fixation completed, press the left spring presser of extruder, put filament vertically into the left filament intake from the other end of filament guidetube. 7. After filament going into filament intake, insert filament guidetube into filament intake to fix. 12 Leveling Berfore leveling, let's learn the funciton of knobs. How to use the knobs Build plate goes up Rotate knob clockwise Build plate goes down Rotate knob anticlockwise 1. Insert the SD card into the SD card slot. 13 FlashPrint PlateLeveling.x3g Test File Unpacking Video 2. Choose [Print from SD], tap [OK]. Choose [PlateLeveling.x3g], tap [OK] to leveling process. Find the 3 knobs on the botton of the platform and tighten four or five turns. In each position, we will need to adjust 2 knobs at the same time. Nozzles are at the right height when you can just slide a sheet of paper between the nozzle and the platform Grab a sheet of paper to assist us. Please wait. 3. After leveling starts, there would be a prompt on the LCD panel. Tap [Ok], turn the page. After prompt is over, extruder starts to move and stops above leveling knobs at the front build plate. Attention: Leveling would affect print effect directly, if print result is unsatisfactory, please do leveling again. Start the adjustment process with the right nozzle, then use the distance between the right nozzle and build plate as a reference. 4. Take leveling card out, on the basis of right side extruder, put leveling card between right extruder and build plate. Slide leveling card back and forth and adjust knobs in the meantime. If you can move leveling card easily, please rotate knobs clockwise to reduce the distance between build plate and nozzle. Otherwise, rotate knobs anticlockwise to increase the distance between build plate and nozzle. If you feel slight friction when moving leveling card, the distance between extruder and leveling card is proper, thus adjustment compeleted. 5. After the first leveling point completed, tap [OK]. The extruder will move to the second leveling point. Adopt same method to adjust. After three leveling points completed all, leveling completed. Tap [Ok] to end leveling process, press leftwards arrow to go back to home screen. 6. Press build plate slowly to the middle of the printer. 14 Loading Filament FF Creator Pro Print from SD Preheat Utilities 1. Choose [Utilities], and then tap [Ok]. Monitor Filament Loading Preheat Settings General Settings 2. Choose [Filament Loading], and then tap [Ok]. Unload right Load right Unload left Load left 3. Choose [Load left], and then tap [Ok]. Heating: Extruder: 26/230C Press left to cancel 4. Extruder starts to heat. Begin loading or unloading. Press the center button when finished. 5. Once heated, filament will be drawn through the extruder. Continue extruding until the extruder provides a steady flow of filament. Tap [OK], go back. Tap leftwards arrow twice, go back to the home screen. Attetion: If extruder can not unload in a long time, please check if you have inserted filament into the bottom of extruder. 15 First Print FF Creator Pro 1. Ensure that the build plate has been leveled before printing. 2. Ensure that the filament has been loaded in an appropriate approach. Print from SD 3. Load the filament for a while to extrude all the melted filament you printed last time out Preheat of the extruder. 4. Print with ABS filament, install top cover, close Utilities the front doorPrint with PLA filament, remove top cover, open the front door. 5. Please clean extruder before printing. 1. Choose [Print from SD], tap [OK]. 6. Do not leave the printer unattended during operation. FlashPrint PlateLeveling.x3g Quick Start Guide Test File 40mmCUBE-Left-PLA 40mmCUBE-Right-PL Hillbert-CUBE-PLA 2. Choose [Test File], tap [OK]. 3. Choose [40mmCUBE-Left-PLA.gx], tap [OK]. Heating: R Extruder: L Extruder: Platform: 15C 15/200C 14/ 50C 40mmCUBE-Left-PLA 0% R Extruder: 26C L Extruder: 200/200C Platform: 50/ 50C 4. The extruder and the build plate starts to heat. 5. After completing preheat, the printer starts to print. 16 Unloading Filament Please follow steps below if you need to unload filament in daily use. Withdraw Filament Guidetube FF Creator Pro Print from SD Preheat Utilities 1. Pull filament guide tube out of filament intake, 2. Choose [Utilities], tap [OK]. leave filament 10cm to pull filament easily. Monitor Filament Loading Preheat Settings General Settings Unload right Load right Unload left Load left 3. Choose [Filament Loading], tap [OK]. 4. Choose [Unload left], tap [OK]. Heating: Extruder: 26/230C Press here Push filament down through for 3 seconds Press left to cancel 5. Extruder starts to heat. 6. When heating to target temparture, press spring presser and push filament down through for 3 seconds until you see steady filament coming out from nozzle. 17 Press here Withdraw Filament 6. Then pull out vertically quickly and release spring presser. Tap [OK], go back. Tap leftwards arrow twice, go back to the home screen. Installation and Dismantlement 18 2. SD 4. 5. 6. 19 7. USB 8. X 10. 11. logo 20 12. 13. FF Creator Pro Print from SD Preheat Utilities 14. 15. [Utilities][OK] Monitor Filament Loading Preheat Settings General Settings 16. Profiles Home offsets Toolhead offsets Jog Mode 18. [Jog Mode][OK] Level Build Plate Home Axes Bot Statistics Filament Odometer 17. Jog Mode X+ (Menu) Y- X- 19. 21 Jog Mode Y+ -X (Menu) ZY- 20. 22. Jog Mode Z-Y (Menu) Z+ 21. Jog Mode Z-Y (Menu) Z+ 23. FF Creator Pro Print from SD Preheat Utilities 24. [OK] 25. 22 x 2 M 3*8 / 2 / / / / M 3*8 / M 3*6 / 23 24 25 1. M2.5 2. 26 27 1. 2. 3. 28 4. PLA 5. 29 6. 7. 30 1. SDSD SD 31 FlashPrint PlateLeveling.x3g Test File Unpacking Video 2. [Print from SD][OK][PlateLeveling.x3g][OK] Find the 3 knobs on the botton of the platform and tighten four or five turns. In each position, we will need to adjust 2 knobs at the same time. Nozzles are at the right heught when you can just slide a sheet of paper between the nozzle and the platform Grab a sheet of paper to assist us. Please wait. 3. [OK] 4. 5. [OK] [OK] 6. 32 FF Creator Pro Print from SD Preheat Utilities 1. [Utilities][OK] Monitor Filament Loading Preheat Settings General Settings 2. [Filament Loading][OK] Unload right Load right Unload left Load left Heating: Extruder: 26/230C Press left to cancel 3. [Load left][OK] 4. Begin loading or unloading. Press the center button when finished. 5. [OK] 33 FF Creator Pro 1. 2. 3. Print from SD 4. ABS Preheat PLA 5. Utilities 6. 3D 1. [Print from SD][OK] FlashPrint PlateLeveling.x3g Quick Start Guide Test File 40mmCUBE-Left-PLA 40mmCUBE-Right-PL Hillbert-CUBE-PLA 2. [Test File][OK] 3. [40mmCUBE-Left-PLA.gx][OK] Heating: R Extruder: L Extruder: Platform: 15C 15/200C 14/ 50C 40mm_Box Left PLA 0% R Extruder: 26C L Extruder: 200/200C Platform: 50/ 50C 4. 5. 34 FF Creator Pro Print from SD Preheat Utilities 1. 2. [Utilities][OK] Monitor Filament Loading Preheat Settings General Settings Unload right Load right Unload left Load left 3. [Filament Loading][OK] 4. [Unload left] [OK] Heating: Extruder: 26/230C 3 Press left to cancel 5. 6. 3 35 6. [OK] 36 4008866023 www.sz3dp.com 518Adobe PDF library 11.00 Adobe Illustrator CC (Windows)