Installation Guide for APS models including: IB-010C, IB-010H, iBoard Series Black Running Boards Style Compatible, iBoard Series, Black Running Boards Style Compatible, Boards Style Compatible, Style Compatible
1 giorno fa — Starting on the driver side front of the vehicle. Locate the (2) mounting locations along the bottom of the body, (pinch weld),. (Figs 1-2).
PART#: IB-010C&H iBoard® Series READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED. *ROCKER PANEL MOUNT *NO DRILLING REQUIRED Fastener Size Tightening Torque (ft-lbs) 6mm 6-7 8mm 16-18 10mm 31-32 12mm 56-58 14mm 92-94 Required X X X PART LIST Driver Side Step Bar Front Passenger Side Step Bar 1# 1# 1# 1# Customer Support: info@iboardauto.com 1 Rev. 20241201 Item QTY Description 1# 4 Mounting Brackets Mounting Bracket List Item QTY Description Hardware Package A (For Bracket Installation) Item QTY Description Item QTY Description 1# 8 M101.5-30mm Hex Bolts 4# 4 M101.5 Hex Nuts 2# 12 M10 Flat Washers 5# 4 M10 Clip Nuts 3# 8 M10 Lock Washers 1 # 2 # 3 # 4 # 5 # Hardware Package B (For Stainless Steel Step Bar Installation) Item QTY Description Item QTY Description 1# 8 M8X1.25-35mm Carriage Bolts 3# 8 M8 Nylon Lock Nuts 2# 8 M8 Large Flat Washers 4# 4 Sliders (Packed with Step Bars) 1 # 2 # 3 # 4 # Customer Support: info@iboardauto.com 2 Rev. 20241201 STEP 1 Starting on the driver side front of the vehicle. Locate the (2) mounting locations along the bottom of the body, (pinch weld), (Figs 1-2). Each mounting location on the inner body panel is comprised of a rectangular hole with a round hole on each side directly above each pair of holes in the pinch weld. Line Up Clip Nuts With Factory Round Hole Factory Hole In Pinch Weld Pictured From Behind Body Panel Front (Fig 1) Driver Side Mounting Locations (Illustrated Back View of Rocker Panel) Front (Fig 3) M10 Clip Nut Installed STEP 3 Partially attach the Driver Front Mounting Bracket to the M10 Clip Nut with the included (1) M10X1.5-30mm Hex Bolt, (1) M10 Lock Washer and (1) M10 Flat Washer, (Fig 4). Bolt the (1) lower hole on the Mounting Bracket to the (1) hole in the pinch weld with the included (1) M10X1.5-30mm Hex Bolt, (2) M10 Flat Washers, (1) M10 Lock Washer and (1) M10X1.5 Hex Nut, (Fig 4). Do not fully tighten hardware at this time. (1) M10X1.5-30mm Hex Bolt (1) M10 Flat Washer (1) M10 Lock Washer (Fig 2) The Mounting Holes on the Pinch Weld STEP 2 Select (1) M10 Clip Nut. Insert the Clip Nut into the rectangular opening. Line up the threaded hole on the Clip Nut with the round hole beside the rectangular opening, (Fig 3). NOTE: Make sure the threaded nut on Clip Nut must toward the inner side of the rocker panel, (Fig 3). (1) M10X1.5-30mm Hex Bolt (2) M10 Flat Washers (1) M10 Lock Washer (1) M10X1.5 Hex Nut (Fig 4) Driver Front Mounting Bracket Installation Customer Support: info@iboardauto.com 3 Rev. 20241201 STEP 4 Move along the vehicle to the driver side rear mounting location. Repeat Steps 1-3 to install the Driver Rear Mounting Bracket. Note: All (4) Mounting Brackets Are Universal. STEP 5 Once all (2) Driver side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 5 & 6) (1) Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts; (2) Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider. (3) Slide the Slider (with carriage bolts) to the Step Bar. (4) Repeat to install the other (1) slider to the step bar. (5) Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (4) M8 Large Flat Washers and (4) M8 Nylon Lock Nuts and (2) Sliders, (Fig 6). Do not fully tighten hardware at this time. Note: The Sliders are packed with the Step Bars. Level and adjust the Step Bar and fully tighten all hardware. Repeat Steps 1-5 for the other side Step Bar installation. The installation is completed!!! Attention Do periodic inspections to the installation to make sure that all hardware is secure and tight. In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only. Slider (2) Carriage Bolts (Fig 5) Slider Installation Slider with (2) Carriage Bolts Step Bar Slider (w/ installed Carriage Bolts) Step Bar (Bottom View) Mounting Bracket (2) M8 Large Flat Washers (2) M8 Nylon Lock Nuts (Fig 6) Step Bar Installation Customer Support: info@iboardauto.com 4 Rev. 20241201Microsoft Publisher LTSC