Ceiling Fan With Light

01. Parts List and Tools

1. Parts List

The following parts are included:

• Hook
• Clevis
• Downrod (6"/10")
• Coupling Cover
• Fan Host
• Fan Blades x5
• Power Cord
• Assembly Kit (includes Remote Control)
• Light Discs
• LED
• Lampshade

2. Tool Required

Tools needed for installation:

• Electrical Adhesive Tape [tape emoji ?]
• 14open Spanner [wrench emoji ?]
• Slotted Screwdriver [screwdriver emoji ?]
• Philips Screwdriver [screwdriver emoji ?]
• Telescoping Ladder [ladder emoji ?]
• Pliers [pliers emoji ?️]

WARNING

1. To avoid the risk of electric shock, ensure the power is turned off at the main fuse box before wiring. Installation must be performed by a licensed electrician.
2. This fan is not compatible with dimmer switches or variable-speed solid-state wall controls.

Maintenance

1. It is recommended to inspect all connecting parts at least once a year, including the mounting bracket, downrod fasteners, and fan blades, to ensure they are secure and functioning properly.
2. Clean the fan blades regularly to maintain performance and reduce dust buildup.
3. The motor bearings are pre-lubricated with grease. Do not apply additional oil or lubricants to the motor.

02. Installation Guide

Note: The fan light is not compatible with dimmer switches or variable-speed solid-state wall controls.

1. Before You Start

• 1A: Wear protective gloves [glove emoji ?] during installation.
• 1B: Ensure a minimum clearance of 2.3 meters (7.5 ft) from the fan to the floor [ruler emoji ?].
• 1C: Turn OFF the power at the main fuse or circuit breaker before installation [power-off symbol ?].

2. Install the Bracket

Choose the appropriate fasteners based on your ceiling material.

For Concrete Ceiling: [Diagram description: Shows mounting bracket installation for concrete ceiling with expansion anchors.]

For Wood Ceiling: [Diagram description: Shows mounting bracket installation for wood ceiling with wood screws.]

For Outlet Box: [Diagram description: Shows mounting bracket installation for an electrical outlet box.]

3. Install the Downrod and Coupling Cover

3A: Loosen the components at the yoke of the downrod assembly.

3B: Slide the canopy and the collar cover onto the downrod.

3C: Assemble the downrod with the canopy and collar cover as shown in the figure.

4. Install the Fan

1. Loosen the four screws on the mounting bracket.
2. Thread the wires through the downrod and connect them to the motor.
3. Insert the safety bolt through the aligned holes.
4. Secure the safety bolt using the safety pin [pin emoji ?].
5. Tighten the jam screws to lock the downrod in place.

5. Installation of Suspension Steps

5a. Remove the screws.

Diagrams show removal of screws and assembly of suspension parts.

Parts involved:

• Clamp plate
• Hanging pulley
• R-clip
• Nut
• Spring washer
• Flat washer
• Flange pin

5b

Install the suspension wheel clamp onto the suspension downrod as shown in the diagram.

5c. OPTION 1: Drill Method

The mounting bracket must be securely fastened to a structural ceiling member.

1. Mark the Hole Pattern

1. Hold the mounting bracket in its final position.
2. Use the bracket as a template and mark the centre of all two holes with a pencil or centre-punch.

2. Select Your Surface & Fastener

OPTION A: Masonry / Concrete / Brick

Hardware (supplied): M6 × 50 mm EXPANSION ANCHORS – 2 pcs

Drill-bit: Ø8 mm (5/16") masonry

Hole depth: 55 mm (50 mm anchor + 5 mm clearance)

Steps:

1. Hammer-drill perpendicular to surface.
2. Blow out or vacuum any dust from the hole.
3. Insert anchor through bracket, tighten 10 mm nut (with 10mm wrench) until bracket no longer moves.

OPTION B: Wood Joist / Timber

Hardware (supplied): M6 x 35 mm SELF-TAPPING SCREWS – 2 pcs

Pilot-bit: Ø 2 mm wood (optional)

Drill a pilot hole: to the full length of the 35 mm screw (optional)

Steps:

1. Drill 2 mm pilot hole to prevent splitting.
2. Drive self-tapping screw through bracket until washer is flush—do not overtighten.

3. Final Safety Check

• Pull on the bracket—no movement means the anchors/screws are set.

Tip: If an expansion anchor spins, the hole is oversize—re-drill with a fresh 8 mm bit.

5d. Assembly Diagram

Follow the diagram for assembly steps labeled a through h.

[Diagram description: Shows detailed assembly steps for the fan motor housing, downrod connection, and light kit attachment.]

Wiring Diagram: [Diagram description: Illustrates the electrical connections for the fan motor and light kit.]

Fan Blades x5

h: Align and rotate the acrylic light cover into place.

Make sure the installation is correct before turning on the power [power-on symbol ⚡].

03. Remote Control Operation

Power Specifications

Remote Control Functions

Remote Re-Pairing Instructions

If your remote control loses connection with the fan, follow the steps below to re-establish the link:

1. Press and hold the (Pairing Key / Fan OFF) button for 3 seconds within 10 seconds of turning on power to the fan.
2. Successful pairing is confirmed when the LED light flashes.