TAC Truck Accessories Company | TACUSA
Installation Guide for TAC models including: TB-D12N, TB-D12N Arrow Side Steps Running Boards, Arrow Side Steps Running Boards, Side Steps Running Boards, Steps Running Boards, Running Boards, Boards
TAC Arrow Side Steps Running Boards Compatible with 2019-2024 Dodge RAM 1500 Quad Cab (Exclude 2019-2024 RAM 1500 Classic) Truck Pickup 5” Aluminum Texture Black Step Rails Nerf Bars Lightweight : Automotive
File Info : application/pdf, 4 Pages, 448.66KB
DocumentDocumentARROW SIDE STEP PART #: TB-D12N FITS: 2019-Up Dodge RAM 1500 Quad Cab (Exclude 2019-2024 RAM 1500 Classic Quad Cab) 60-120 min Cutting Not Required Drilling Not Required Part List Torque & Tools Fastener Size 6mm 8mm 10mm 12mm Tightening Torque (ft-lbs) 7-8.5 18-20 35-40 60-70 Wrench Required 10mm 13mm 16mm 18mm Allen Wrench Required 4mm 5mm 6mm 8mm BEFORE INSTALLATION REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED. Sticker "D" for Driver / Left Side Front Sticker "P" for Passenger / Right Side #2 #1 #2 #1 #5 #3 #3 #5 #2 www.tacautoparts.com #2 #1 #1 #1: Front/Rear Lower Mounting Bracket x 4 #2: Front/Rear Upper Mounting Bracket x 4 #3: Center Mounting Bracket x 2 #4: Center Support Bracket x 2 Customer Support: tac-office@tacautoparts.com x8 x16 x20 x28 x12 x12 x12 x12 8mm x 25mm Hex Bolt 8mm x 16mm Flat Washer 8mm x 24mm Flat Washer 8mm Nylon Lock Nut 6mm x 20mm T-Bolt 6mm x 22mm 6mm Lock 6mm Hex Flat Washer Washer Nut PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE DRIVER SIDE INSTALLATION FIG 2 (3) 8mm x 24mm Flat Washers (3) 8mm Nylon Lock Nuts STEP 1 Start the installation under the Driver/Left side of the vehicle. Locate the front (3) factory studs along the inner side of the body panel, (Fig 1). FIG 1 Front (Fig 1) Driver/Left Front mounting location Front (Fig 2) Attach (1) Front/Rear Upper Mounting Bracket (#2) to the threaded studs STEP 3 Attach (1) Front/Rear Lower Mounting Bracket (#1) to the welded plate on the back of the Front Upper Bracket (#2) with (2) 8mm Hex Bolts, (4) 8mm x 16mm Flat Washer, and (2) 8mm Nylon Lock Nuts (Fig 3). FIG 3 STEP 2 Select (1) Front/Rear Upper Mounting Bracket (#2), Attach the Mounting Bracket to the (3) factory studs with (3) 8mm x 24mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Fig 2). Do not tighten hardware. (2) 8mm Hex Bolts (4) 8mm x 16mm Flat Washers (2) 8mm Nylon Lock Nuts (Fig 3) Driver/Left Front mounting location www.tacautoparts.com Page 1 of 3 Rev. 10/18/22 (NL) STEP 4 Move to the center location, (Fig 4). Select (1) Center Support Bracket (#4), attach the Support Bracket to the lower (2) factory studs with (2) 8mm x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 5). FIG 4 FIG 6 (2) 8mm x 24mm Flat Washers (2) 8mm Nylon Lock Nuts (Fig 6) Attach Mounting Bracket to the upper mounting stud and Support Bracket Front (Fig 4) Driver/Left Center mounting location FIG 5 (2) 8mm x 24mm Flat Washers (2) 8mm Nylon Lock Nuts (Fig 5) Attach (1) Center Support Bracket (#4) to the lower (2) threaded studs on the mounting location STEP 5 Select (1) Center Mounting Bracket (#3) and attach to the Support Bracket and upper threaded stud with (2) 8mm x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 6). Do not tighten hardware. STEP 6 Repeat Steps 2 & 3 to attach (1) Front/Rear Upper Mounting Bracket (#2) and (1) Front/Rear Lower Mounting Bracket (#1) to the rear mounting locations along the body panel, (Fig 7). Do not tighten hardware. FIG 7 Rear (Fig 7) Driver/Left Rear mounting location www.tacautoparts.com Page 2 of 3 Rev. 10/18/22 (NL) STEP 7 Select the Driver/Left Side Step. Insert (6) 6mm TBolts into the slots underneath the Side Step (Fig 8). NOTE: The Driver/Left Side Step will have a Sticker "D" on the front. IMPORTANT: Do not slide the Side Step front to back or damage to the finish may result. Attach the Side Step to the (3) Mounting Brackets with (6) 6mm Flat Washers, (6) 6mm Lock Washers, and (6) 6mm Hex Nuts (Fig 9). Do not tighten hardware. FIG 8 STEP 8 Level and adjust the Side Step as necessary and fully tighten all hardware. STEP 9 Repeat Steps 1-8 to attach the Passenger/Right Side Step to the vehicle. (Fig 8) Insert (6) 6mm T-Bolts into the slot underneath the Side Step FIG 9 STEP 10 Do periodic inspections to the installation to make sure that all hardware is secure and tight. Attention To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean the Side Steps. (2) 6mm Flat Washers (2) 6mm Lock Washers (2) 6mm Hex Nuts (Fig 9) Attach Side Step to the Mounting Brackets www.tacautoparts.com Page 3 of 3 Rev. 10/18/22 (NL)