SIMATE Electric Scooter User Manual

I. Package Contents:

• Handlebars
• Accessories
• Electric Scooter
• Charger
• User Manual
• Hex Wrench

II. Installation Steps:

1. Insert the handlebars as illustrated and tighten the screws.
2. Perform an initial power-on check.

Function Diagram

A diagram shows the various parts of the electric scooter:

• Power Switch: Quickly click the Power Button to operate.
• Control Panel
• Electronic Brake
• Electronic Throttle
• Folding Hook
• Front Light on the Steering Tube
• suspension
• Light
• Folding Mechanism
• Charging Port
• Light
• Mudguard Brake
• Hub Motor
• Parking Stand

Note: Long press the Power Button for 3 seconds to Power On, activate Energy-Saving Mode, and turn off the Front Light.

III. Safety Precautions:

1. Before using the electric scooter, ensure your child is equipped with appropriate safety gear, such as a helmet, wrist guards, and knee pads.
2. Avoid using the electric scooter on wet, slippery surfaces, steep slopes, or in complex traffic environments.
3. Do not continue to use the scooter when the battery is low to avoid battery over-discharge.
4. Do not press the throttle while walking with the scooter.
5. Avoid obstacles while riding.
6. Do not hang heavy items on the handlebars.
7. Do not ride with one foot.
8. Do not drive on public roads, motorways, or highways.
9. Do not make substantial turns of the handlebars while driving at high speed.
10. Do not drive in standing water.
11. Do not allow more than one person to ride the scooter at a time or carry a child while riding.
12. Do not step on the folding switch while riding.
13. The wheel motor may become hot during operation; avoid touching it.
14. Do not drive without holding the handlebars. Do not drive with one hand.
15. Do not ride the scooter up or down steps or jump obstacles.
16. Hold the handlebars tightly with both hands, otherwise, you may lose balance or fall and seriously injure yourself.

IV. Using the Electric Scooter:

1. Ensure the scooter's battery is fully charged.
2. Power on the scooter and check the battery indicator light. If the battery is low, charge it immediately.
3. Stand on the scooter with one foot and use the other foot to push off and start moving.
4. Place the other foot on the scooter, and keep both feet stable. Once balanced, gently press the throttle on the right handle to accelerate. The motor will not start until the scooter reaches 3km/h for safety reasons.
5. Release the throttle to slow down. For emergency braking, quickly pull the brake lever and use your foot to press the rear mudguard to trigger the mechanical brake.
6. When turning, slightly lean your body weight towards the direction of the turn and slowly turn the handlebars.
7. When your child is done using the scooter, turn off the power switch on both the scooter and the controller.

Technical Specifications

V. Charging the Battery:

1. Plug the charger's power cord into the power socket.
2. Insert the charger's charging plug into the charging port on the scooter and controller.
3. When the charger's indicator light turns from red to green, the battery is fully charged.
4. Do not use other models or brands of batteries, as it may pose a safety risk.
5. Avoid touching the battery contacts, disassembling, or puncturing the casing. Avoid metal objects contacting the battery contacts to prevent short circuits, which could cause damage to the battery or injury.
6. Improper disposal of used batteries can severely pollute the environment. Discard the battery pack according to local regulations.
7. Do not place the battery in a high temperature above 50°C or a low temperature below -20°C. Do not throw the battery into fire, as it may lead to battery failure, overheating, or fire risk.
8. Only use the original charger for charging, otherwise, there is a risk of damage or fire.
9. Do not disassemble the charger casing by yourself. Avoid touching the interface contacts with metal objects when powered on, as it may cause electric shock or charger damage, which is not covered by the warranty.

VI. Daily Maintenance and Care:

Cleaning and Storage

Wipe the main frame clean with a soft damp cloth. For stubborn stains, apply toothpaste and scrub with a toothbrush, then clean with a soft damp cloth. Scratches on plastic parts can be polished with fine sandpaper.

Tips: Do not use alcohol, gasoline, kerosene, or other corrosive, volatile solvents to clean your scooter. Do not use pressure washers or hose sprays.

Warning: Before cleaning, ensure the scooter is turned off, the charging cable is unplugged, and the charging port cover is securely fastened. Failure to do so may damage electronic components. Store the scooter in a cool, dry place when not in use. Do not leave the scooter outdoors for extended periods. Sun exposure and extreme temperatures can accelerate the aging of plastic parts and reduce battery life.

Battery Maintenance:

When storing or charging the battery, do not exceed the specified temperature limits. Do not puncture the battery. Please refer to local laws and regulations regarding battery recycling and disposal.

A well-maintained battery performs well even after many miles. Charge the battery after each ride and avoid completely depleting it. Battery performance is optimal at 22°C. At temperatures below 0°C, performance may decline. At -20°C, battery performance is halved compared to 22°C. Performance recovers as temperature increases.