ELECTRIC SCOOTER Instruction Manual

Product Parameters

GT06PLUS

GT06

Packing List

Dear Customer:

Thank you for choosing your electric scooter. After opening the package, please carefully check whether the accessories you received are complete. If there are any discrepancies, please contact us in time and we will reissue them to you as soon as possible.

Details on installing and using the video webpage: https://bit.ly/3clgwtw

• Assembly Tools
• Charger
• Tire Patch Screws
• Instructions

Folding buckle for safe use

Be careful of hand injuries during folding operations. For detailed folding instructions, please refer to the manual.

1. Check the warning message for the disassembly lock position. Folding switch needs to be used correctly.
2. The folding gesture should be based on the image. Pull the folding buckle outward with force.
3. Save gesture, open the folding lock buckle. You can watch the operation video for detailed operation.

Foot Support Installation Instructions

1. Foot Support Installation
2. Put on the foot brace rubber sleeve.
3. Tighten the screws on the back of the foot support.
4. Installation completed.

Wiring Instructions

*SO THE JACK MUST BE SLOTTED INTO THE SLOT, OTHERWISE IT WILL DAMAGE THE ENTIRE SCOOTER WIRING*

*SLOT TO SLOT INSERTION*

BRAKE INTERFACE

*SLOT TO SLOT INSERTION*

LIGHT SWITCH / SCREEN DISPLAY INTERFACE

*SLOT TO SLOT INSERTION*

KEY LOCK INTERFACE

Light Switch / Screen Display Interface: Headlight switch and display interface.

Brake Interface: Left and right brake connection interface.

Key Lock Interface: Key lock interface display.

Schematic Diagram Of Meter Icon (GT06PLUS)

Instrument Commonly Used Icons

RED WARNING

• MOTOR FAULT
• CONTROLLER MALFUNCTION
• THROTTLE MALFUNCTION
• BRAKE POWER OUTAGE

• LEFT TURN SIGNAL
• HEADLIGHT DISPLAY
• BLUETOOTH DISPLAY
• CRUISE CONTROL
• RIGHT TURN SIGNAL

• SINGLE AND DUAL DRIVE DISPLAY
• PEDESTRIAN DISPLAY
• ONE FILE DISPLAY
• SECOND LEVEL DISPLAY
• THREE LEVEL DISPLAY

Schematic Diagram Of Meter Icon (GT06)

Instrument Commonly Used Icons

• CHARGE
• MOTOR FAILURE
• CONTROLLER FAILURE
• BRAKING
• 1ST GEAR LOW SPEED
• 2ND GEAR MEDIUM SPEED
• 3RD GEAR HIGH SPEED
• HANDLEBAR FAILURE

• HEADLIGHTS
• THE WIDTH LIGHT
• SINGLE MILEAGE
• TOTAL MILEAGE
• TURN LEFT
• TURN RIGHT
• P GEAR PARK

NFC INPUT SETTINGS (GT06PLUS)

1. Simultaneously press the Lights and Settings buttons on the control panel to enter NFC Settings mode.
2. When entering NFC settings, the screen will display the number of NFC inputs entered, and the new scooter usually displays 00.
3. After entering the input mode, bring the NFC card close to the console.
4. Successfully entered NFC, the screen will display the number of entries as 01.
5. Press the D/S button to exit NFC mode.
6. After pressing the power button to turn on the power, flash NFC to start the scooter.

Video operation: https://bit.ly/3clgwtw

Product Part Name (GT06PLUS)

• THROTTLE
• FOLD SWITCH
• HEADLIGHTS
• FRONT BRAKE DISC
• INSTRUMENT SCREEN
• CONTROLLER CONSOLE
• VEHICLE LIGHTING EFFECT
• 11 INCH VACUUM OFF-ROAD TIRES

Product Part Name (GT06)

• LIGHT SWITCH
• SPEAKER
• GEAR POSITION
• TURN SIGNAL
• BRAKE HANDLE
• VOLTAGE SWITCH KEY
• KEY LOCK
• INSTRUMENT SCREEN
• FOLD SWITCH
• FRONT HEADLIGHTS
• COVER PLATE
• 11 INCH VACUUM OFF-ROAD TIRES

Key Function (GT06PLUS)

• Start key: Long press this button to start the vehicle and turn it off.
• Light switch: Vehicle headlight start button.
• Menu: Shift switch button.
• Single and Double Drive (D/S): Single/dual drive conversion button.
• Speaker: Vehicle horn button.

Instrument and function (GT06PLUS)

PARAMETER SETTING

Long press and hold the "three horizontal buttons" in the "power on state" section will switch from displaying normal speed to displaying Px(x=0, 1, 2, 3, 4, 5, 6, 7, 8, 9), Px represents different setting items, and enters the setting state at this time.

INSTRUMENT PARAMETERS

• P0: The software version is not adjustable;
• P1: Speed unit setting; (1: Mph 0: Kmh)
• P2: Cruise control setting; (1: Open 0: Close)
• P3: Sliding start; (1: Open 0: Close)
• P4: Wheel diameter setting;
• P5: Battery type;
• P6: Restore factory settings;
• P7: Bluetooth Settings; (1: Open 0: Close)
• P8: Check the throttle value;
• P9: Check the brake value;

Regular Inspection & Maintenance

How To Use The Charger Correctly

1. When using the charger to charge the scooter, the charging port of the scooter should be connected first (Please align the output port of the charger with the scooter's charging port.).
2. The charging place should be far away from children, and ensure that the charging environment is ventilated, dry, and away from flammable and explosive materials.
3. Please be sure to use the company's special charger for charging. Otherwise, it will affect the life of the battery or damage the battery.
4. After the charger turns green, unplug it within two hours to stop charging.
5. If not charging, disconnect the charger from the charging socket promptly.
6. After the charging is completed, you should first pull out the power plug before pulling out the plug of the scooter.
7. After the power is turned on, the red light indicates that the charging is in progress. When the charger indicator turns green, the charging is completed. When the battery is almost full, the red and green lights will flash alternately.