Login – Qolsys
IQ Shock Mini-S – QOLSYS
Installation Guide for olsys models including: IQ Shock Mini-S Encrypted Door Window Sensor, IQ Shock Mini-S, Encrypted Door Window Sensor, Door Window Sensor, Window Sensor, Sensor
IQ Shock Mini-S – QOLSYS
File Info : application/pdf, 2 Pages, 219.77KB
DocumentDocumentIQ SHOCK MINI-S QUICK INSTALL GUIDE STEP CHOOSE 1 INSTALLATION LOCATION STEP DIP 2 SWITCH CONFIGURATION Two dip switches allow you to customize the behavior of this device: Sliding glass doors Windows Exterior Doors SPECIFICATIONS Sensor: 2.5"H x 1"W x .5"D Code outputs: tamper, tamper restore, alarm, alarm restore, low battery. Transmitter frequency: 319.5 MHz Supervisory keep-alive interval: 70 minutes. RF Peak field strength: typical 36000 uV/m at 3m UL/ULC listed for residential use only Operating Temperature: -5C~45C Relative Humidity: 5-95% Non-Condensing Storage Temperature: -25-70C Replace battery with exact replacement every 5 years with 3V CR2032 Lithium (x2). DS#1 - Installer Test Mode: ON: - Calibrates accelerometer orientation. - LED is Active for dialing in shock sensitivity with potentiometer. - Please note, when test mode is enabled (ON) the IQ Shock Mini will NOT transmit signals to the IQ Panel. This mode is only used for initial installation and calibration of the shock sensor. OFF: - Disables installer test mode. SENSITIVITY LEVEL MAX MIN DS#2 - Reed Switch: ON: - Enables reed switch (must be ON for UL installations). OFF: - Disables reed switch. Sensitivity Level: CLOCKWISE: - More Sensitive COUNTERCLOCKWISE: - Less Sensitive ON 12 LED MAGNET DIP SWITCHES IMPORTANT NOTE: The IQ Shock is intended to be installed on doors with or without glass inserts and on window frames but not on the actual glass surface. This is a quick guide for experienced installers only. Refer to http://dealers.qolsys.com (login required) STEP REMOVE 3 BATTERY TABS STEP APPLY 4 ADHESIVE STEP MOUNT 5 SENSOR & MAGNET STEP LEARN 6 INTO PANEL 1" MAX ADD Place your panel in "Auto Learn" mode Open and close the case to "tamper" the device Customize name and settings as desired and and touch "ADD" STEP ADJUST 7 SHOCK SENSITIVITY Adjusting the Shock Sensitivity: IMPORTANT: Calibrate the IQ Shock Mini's accelerometer from the final mounting position by moving dip switch 1 to ON (enable installer test mode). While in this mode the LED will flash RED when it detects a shock level strong enough to trigger an alarm at the control panel. There are 3 total sensitivity settings and the LED will flash each time the sensitivity threshold is changed. Please note that no RF transmission from the sensor occurs during installer test mode. Gently hit (using the palm of your hand) the surface on which the device is installed. Gradually increase the pressure or turn the shock sensitivity adjustment dial clockwise with a small screwdriver until the desired response is obtained. Ensure that the device is not triggered by accidental vibration (e.g., wind, birds, window coverings) hitting the protected window or surface. Normal traffic or operation of the door/window should not trip the shock sensor. When testing the sensitivity of the unit, do not cause stress or damage to the mounting surface or to the glass. WARNING: In order to avoid personal injury while testing sensitivity, do not apply pressure to glass inserts or windows. Scan for full manual Move dip switch 1 to OFF (disable installer test mode) once shock sensitivity has been set to the desired level. Verify that the IQ Shock Mini properly communicates with the Panel. https://bit.ly/45wgm9o Document#: IQSM-QG Revision#: 05/25/23 Qolsys Product #: IQSM FCC ID: 2AAJXQS-IQSKM IC: 11205A-QSIQSKM UL/ULC NOTE: The IQ Shock Mini - S has been listed by UL/ULC for residential applications only and in accordance with the requirements in the Standards UL 634 and UKLC/ORD-C634 for Door and Window Contact with supplementary Shock Sensor. The shock sensor is for supplementary detection only and not for primary protection of the surface and is not intended for use as a glass break detector. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter toute interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil.