User Guide for BenQ models including: AR19_D e-Reading Lamp, AR19_D, e-Reading Lamp, Lamp
Use only the supplied power adapter and connect only to suitable outlet power (100-240V AC,. 50-60 Hz). Otherwise the lamp will fail to work normally or ...
File Info : application/pdf, 19 Pages, 4.91MB
DocumentDocumentWiT MindDuo RS (AR19_D) e-Reading Lamp
© 2023 BenQ Corporation. All rights reserved. Rights of modification reserved.
Package Contents
Check the packaging for the following items. If any is missing or damaged, please contact the place of purchase immediately.
· WiT MindDuo RS lamp x 1
· Power adapter x 1
· Pedestal base (or desk clamp) x 1
· Screw x 2
· Hex L-key x 1
· The illustrations in this guide are for your reference only and may look different from the appearance of the actual product.
· Actual accessories (e.g., pedestal base or desk clamp) included in the package will depend on the model you purchase. The desk clamp is also provided as separate purchase. Please contact your dealer for availability.
For Your Safety
· Use only the supplied power adapter and connect only to suitable outlet power (100-240V AC, 50-60 Hz). Otherwise the lamp will fail to work normally or result in a fire hazard.
· In order to prevent any damages to the lamp, do not hang or place any objects on the lamp.
· Route the power cord so as to avoid it from being walked on or pinched by items placed upon or against it.
· Place the lamp only on a solid, flat and stable surface. Otherwise the lamp may topple over and result in damages.
· If the lamp will not be used for a long period of time, unplug it from the power outlet.
· The light source contained in this luminaire can't be replaced.
CAUTION
· In case of the following situations, unplug the lamp from the power outlet immediately and contact the authorized service center or a qualified service person for inspection or repair:
- When the outer casing of the lamp is broken
- When there are strange odors coming from the lamp
- When the LED light source flickers
- When the insulation of the lamp's wiring is damaged or frayed, and the metal strings inside can be seen
· Do not use the lamp in a humid environment (like in a bathroom or outdoors). Otherwise the components inside may short-circuit and result in accidents.
· This lamp is designed for indoor use only. Do not use it outdoors.
· Never disassemble the lamp or remove any components from it, as doing so may result in accidents and will void the product warranty.
Installation
Pedestal Base
1. Insert the shaft on the lamp body into the hole on the top of the lamp arm [Figure A 1 ]. When inserting, note the direction of the shaft and ensure that the lamp body is horizontally seated on the lamp arm.
2. Secure the lamp body to the lamp arm by tightening the two screws using the hex L-key provided [Figure A 2 ].
3. Place the pedestal base on a solid, flat and stable surface.
4. Insert the shaft on the pedestal base into the hole on the end of the lamp arm [Figure A 3 ] and then secure it by tightening the screw [Figure A 4 ].
· Be sure to tighten the screw to secure the pedestal base to the lamp arm. Otherwise the pedestal base will detach from the lamp arm and result in damages or personal injuries if the lamp is unwittingly moved by grasping the lamp arm.
· Use only the pedestal base supplied in the packaging to ensure that the lamp can stand firmly.
English
1
5. Press the cable into the groove on the lamp arm [Figure A 5 ]. Note that at least 8 cm of excess length should be left in order for the lamp body to move freely.
6. Connect the power cord to the power adapter [Figure A 6 ] and plug it into a power outlet [Figure A 7 ]. When the power is plugged, the lamp will automatically turn ON.
Upon receiving power from the power outlet, the lamp's built-in presence sensor will start to calibrate automatically, and the process will take approximately 1 minute. Please DO NOT turn off the lamp during the calibration process. You can start using the lamp when the calibration is complete.
Desk Clamp
1. Insert the shaft on the lamp body into the hole on the top of the lamp arm [Figure B 1 ]. When inserting, note the direction of the shaft and ensure that the lamp body is horizontally seated on the lamp arm.
2. Secure the lamp body to the lamp arm by tightening the two screws using the hex Lkey provided [Figure B 2 ].
3. Press the cable into the groove on the lamp arm [Figure B 3 ]. Note that at least 8 cm of excess length should be left in order for the lamp body to move freely.
4. Place the desk clamp onto the edge of the desk surface [Figure B 4 ] and then secure the desk clamp by tightening the clamp screw [Figure B 5 ]. The maximum clampable thickness of the desk clamp is 6 cm.
5. Insert the shaft on the desk clamp into the hole on the end of the lamp arm [Figure B 6 ], and then secure it by tightening the screw [Figure B 7 ].
Be sure to tighten the screw to secure the desk clamp to the lamp arm.
6. Connect the power cord to the power adapter [Figure B 8 ] and plug it into a power outlet [Figure B 9 ]. When the power is plugged, the lamp will automatically turn ON.
Upon receiving power from the power outlet, the lamp's built-in presence sensor will start to calibrate automatically, and the process will take approximately 1 minute. Please DO NOT turn off the lamp during the calibration process. You can start using the lamp when the calibration is complete.
Using the Lamp
Turning On/Off the Lamp
To turn on or off the lamp, place your hand at least 2 cm
under the on/off sensor [Figure C 1 , C 2 ].
C
If the presence detection function is turned on, the lamp
will turn on automatically when you enter the detection
area. To turn off the lamp, place your hand at least 2 cm
under the sensor.
2 cm ON/OFF
2
English
Turning On/Off the Presence Detection Function
The presence detection function allows for the lamp to turn on automatically when you enter the detection area [Figure D ]. To turn on the presence detection function, move the presence detection switch located on the lamp body to the ON position [Figure E ]. To turn the function off, move the switch to the OFF position.
E
Presence Detection
Function
D 45 cm
30 cm
· Do not block the presence sensor on the lamp. Otherwise the presence detection function will not work properly.
Lighting mode indicator
· When the presence detection function is on, the lamp will turn off automatically to save power if you leave the detection area for 30 minutes.
Presence sensor
· With the presence detection function turned on, the lamp will automatically calibrate the Presence sensor when power is connected to the lamp or when the lamp is turned off. The calibration process takes approximately 40 seconds. During calibration, the Lighting mode indicator will light up green and orange alternately, and the presence detection function will be disabled temporarily.
· To ensure normal operation of the presence detection function, please keep the lamp away from strong electromagnetic sources (like a Wi-Fi router).
Toggling Preset/Manual Lighting Modes
The lamp provides two preset lighting modes and one manual lighting mode that allows you to adjust the brightness and color temperature manually.
Lighting mode
Book reading Digital reading
Manual
Setting
Color temperature
Brightness level
5700K 4000K
Automatically optimized according to ambient lighting
condition
Adjustable
Adjustable
Lighting mode indicator color
Orange
Green
None (off)
To toggle among lighting modes, press and hold the rotary knob on the lamp body for 2 seconds. The Lighting mode indicator lights up in the Book reading mode (orange) and Digital reading mode (green), and becomes off in the Manual mode.
In the Manual mode, you can manually adjust color temperature and brightness level using the rotary knob on the lamp body.
1. Press the rotary knob to select the setting: the inner white circle on the rotary knob represents brightness level setting, and the outer color circle represents color temperature setting.
When pressing the knob, be careful not to block the on/off sensor.
Color temperature setting (color)
Lighting mode indicator
Brightness level setting (white) Illuminance indicator
English
3
2. Rotate the rotary knob to adjust the setting.
· Rotate the rotary knob clockwise to increase brightness level, or counter-clockwise to decrease it.
· Rotate the rotary knob clockwise to increase color temperature (the light becomes whitish), or counter-clockwise to decrease it (the light becomes yellowish).
In the Manual mode, the lamp's sensor detects the illuminance of the desktop and the Illuminance indicator on the rotary knob indicates the illuminance condition in three different colors:
· Red: The illuminance condition is too dark. Please increase the lamp's brightness level.
· Green: The illuminance condition is good.
· Blue: The illuminance condition is too bright. Please decrease the lamp's brightness level.
· When the lamp is turned off, the illuminance indicator will still light up in red, green or blue to
indicate the illuminance condition of the desktop.
· If the lamp is left on for 30 minutes, the Illuminance indicator will flash (in red, green or blue) to remind you that your eyes need a rest after a 30-minute reading.
Adjusting Angle
You can adjust the angle of the lamp arm according to your desktop
space to obtain a suitable lighting effect.
· The lamp arm pivot is spring-loaded. Tighten the lamp arm pivot by
turning the pivot knob clockwise [Figure F ].
F
· Refer to [Figure G ] for the safe angle range of lamp arm
adjustment.
G
34f
34f
45f
45f
60f
Maintenance and Troubleshooting
· Turn off the lamp first, and unplug the lamp from the power outlet. Wipe any smears or dusts off the lamp's outer casing using a soft, lint-free cloth lightly moistened with a mild detergent solvent. Do not use alcohol or any other chemical solvents like kerosene, naphtha and so on, as the lamp's casing may become damaged.
· Do not rinse the lamp or any of its components directly with water.
· If the lamp does not turn on, check to make sure that there are no loose connections between the power cord, power adapter, and the power outlet.
· If the problem persists, please contact the original place of purchase for help.
Specifications
Model DC power input Max. power consumption Dimensions [Figure H ]
AR19_D 12V, 1.5A 18W 345 x 385 x 500 mm (Width x Depth x Height)
4
English
H 24 cm
34.5 cm
38.5 cm
45 cm 22 cm
50 cm
English
5
· WiT MindDuo RS 1
· 1
· ( )1
· 2
· L 1
· ·
· 100-240V AC50-60Hz
· · ·
·
· - - - LED
- ·
· ·
1. [ A 1 ]
2. L [ A 2 ]
3. 4. [
A 3 ] [ A 4 ]
·
· MindDuo RS ( ) MindDuo ( )
5. [ A 5 ] 8
1
6. [ A 6 ] [ A 7 ]
1
1. [ B 1 ]
2. L [ B 2 ]
3. [ B 3 ]
8 4. [ B 4 ] [
B 5 ] 6 cm
5. [ B 6 ] [ B 7 ]
6. [ B 8 ] [ B 9 ]
1
/
2
[ C 1 , C 2 ]
C
2
2 cm
ON/OFF
2
/
[ D ] (ON) [ E ] (OFF)
E
Presence Detection
Function
D 45 cm
30 cm
·
· 30
· 40
· ( Wi-Fi )
/
5700K 4000K
( )
2 1.
( )
( )
3
2.
·
· ( ) ( )
· · ·
· · 30 ( ) 30
·
[ F ]
F
· [ G ]
G
34f
34f
45f
45f
60f
·
· · ·
DC
[ H ]
AR19_D 12V, 1.7A 18W PS20G120K1700UD 345 x 385 x 500 mm ( x x )
4
H 24 cm
38.5 cm
45 cm
50 cm
22 cm
34.5 cm
(Pb)
(Hg)
(Cd)
(Cr+6)
1. 2.
(PBB)
(PBDE)
5
· WiT MindDuo RS x 1
· x 1 ·L x 1
· x 1 · x 2
·
·
· 100-240V AC50-60 Hz
·
·
·
·
·
- - - LED
-
·
·
·
1. A 1
2. L A 2
3. 4. A 3
A 4
·
·MindDuo ( ) MindDuo RS ( )
1
5. A 5 8cm
6. A 6 A 7
1
1. B 1
2. L B 2
3. B 3 8cm
4. B 4 B 5
6 cm 5.
B 6 B 7
6. B 8 B 9
1
C 1 C 2 2 cm
C
2 cm
2 cm ON/OFF
2
D
ON E OFF
E
Presence Detection
Function
D 45 cm
30 cm
·
· 30
· 40
· Wi-Fi
2
5700K 4000K
2
1.
3
2. ·
·
3 · · ·
·
· 30 30
·
F F · G
G
34f
34f
45f
45f
60f
·
· ·
·
DC H
AR19_D 12V1.5A 18W 345 x 385 x 500 mm x x )
4
H 24 cm
34.5 cm
38.5 cm
45 cm 22 cm
50 cm
5
Acrobat Distiller 22.0 (Windows)