Roll A Shade - Commercial Window Shade Solutions
Roll A Shade - Commercial Window Shade Solutions
Installation Guide for ROLL-A-SHADE models including: RAS-4, RAS-4 4-6 Inch Contract Plus Roll Shade, 4-6 Inch Contract Plus Roll Shade, Roll Shade, Shade
File Info : application/pdf, 6 Pages, 897.17KB
DocumentDocument12101 Madera Way Riverside, CA 92503 Phone: 888-245-5077 Fax: 951-245-5075 www.rollashade.com RAS - Installation Instructions Contract Plus+ Shade 4-6" Contract Manual Hardware Included Tools Required Self Tapping Screws for Aluminum Self Tapping Phillips Screws for Tension Device Wood Screws (If requested) Plastic Connectors Metal Stop Balls 3/8" Drill Bit Drill Phillips Head 1. Install Cassette Box Pre-drill mounting holes in top or back of cassette box. Attach the cassette box to the window frame, window molding, or ceiling per diagram. Two screws must be installed in each end as shown. Additional screws should be used in the center if the cassette box is over 3 ft wide. 2. Install Shade Insert the spring loaded end of the shade into the round hole of the bracket. Next, on the other side of the shade, insert the hook arms of the clutch straight into the two hook arm receiver holes of the bracket. Gently pull down the clutch until the two hook arms have locked securely to the bracket. The bottom of the clutch should always point straight down. 3. Shade Adjustment (If Necessary) Roll shade up and down to confirm bottom rail is level and material rolls up straight on center tube. If the bottom rail is not level, lower shade until you see the metal tube. Add layers of masking tape to the metal tube to the end that is too low until bottom rail is straight. If the material tracks to one side, lower shade until you see the metal tube. Add layers of masking tape Masking Tape www.rollashade.com © Copyright 2021 Roll-A-Shade Inc., All rights reserved. - Contractor #916075 Rev: 01.21.2021 Page 1 of 2 4. Install Cassette Box Bottom Closure Attach the bottom enclosure by hanging it on the front box hanger. Please note, the bottom closure should not interfere with the operating chain. 5. Install Chain Anchor The chain anchor is a plastic piece that is attached to the chain to secure it from possible accidents. Position the chain anchor on the window frame so that the chain anchor and chain do not interfere with raising or lowering the shade. The chain anchor should be installed without stretching or pulling down on the chain. Leave a little play through the chain anchor to allow the chain to pass freely. Do not twist or cross the bead chain. Secure the anchor with Phillips screws in both upper and lower holes. Warning: Failure to use this device may cause injury or death Young children can STRANGLE in cord and bead chain loops. They can also wrap cords around their necks and STRANGLE. · Always keep cords and bead chains out of children's reach. · Move cribs, playpens, and other furniture away from cords and bead chains. Children can climb furniture to get to cords. · Attach tension device to wall or floor. This can prevent children from pulling cords and bead chains around their necks. Fasteners provided with the tension device may not be appropriate for all mounting surfaces. Use appropriate anchors for the mounting surface conditions. www.rollashade.com © Copyright 2021 Roll-A-Shade Inc., All rights reserved. - Contractor #916075 Rev: 01.21.2021 Page 2 of 2 TENSION DEVICE INSTALL ATION INSTRUCTIONS Rollashade.com info@rollashade.com 951.245.5077 © Copyright Roll-A-Shade® Inc. All Rights Reserved. HARDWARE INCLUDED Tension Device + Chain Tension Device Bracket Short Screws Screws INSIDE OR OUTSIDE APPLICATION OUTSIDE INSIDE TOOLS REQUIRED 3/8" Hex Head Phillips Head 1/8" Drill Bit Drill INSIDE OUTSIDE RASTDV2VER.2 2 OF 4 | © Copyright Roll-A-Shade® Inc. All Rights Reserved. INSIDE MOUNT & TENSION DEVICE INSTALLATION Pull the Chainhold down until the chain is fully tensioned (plunger will be fully raised). Screw device into wall. A B KEEP TENSION C SECURE TENSION DEVICE NOTE: Please make sure shade operates smoothly. RASTDV2VER.2 3 OF 4 | © Copyright Roll-A-Shade® Inc. All Rights Reserved. OUTSIDE MOUNT & TENSION DEVICE INSTALLATION With provided screws, install bracket first with large screws (use Chainhold marked screw hole locations as reference). Pull the Chainhold down until the chain is fully tensioned (plunger will be fully raised). Install Chainhold into bracket with small screws. A B PULL CHAIN DOWN & MARK LOCATION C REMOVE TENSION DEVICE & DRILL D E PLACE TENSION DEVICE ON BRACKET F SECURE TENSION DEVICE NOTE: Please make sure shade operates smoothly. RASTDV2VER.2 4 OF 4 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.