teddyDen Bed Assembly Instructions

Assembly Requirement

• 2 Person Assembly
• 15 Minutes Assembly Time (Approximate)

Tools Required

• Allen Wrench

Assembly Preparation

1. Remove all packaging materials, staples, and packing straps from the carton.
2. Refer to the Parts Checklist and ensure all parts are complete before you start assembling.
3. Place all components on a clean, flat, and soft surface (e.g., carpet or rug) to prevent parts from getting scratched.

Tips for Assembly

1. Allow ample room for assembly and in close proximity to where the product will be placed.
2. Assemble the product on a surface that does not scratch or damage the exterior and finish of the furniture.
3. During assembly, do not over-tighten any fittings as this may cause damage.
4. Do not use power tools to assemble this product.
5. Do not sit or stand on the partially assembled product; only use the product for which it is intended.

Care and Use

• Avoid placing the bed in direct sunlight.
• Vacuum regularly on low suction.
• Blot spills immediately with an absorbent towel or clean, damp cloth.
• Spot clean with upholstery shampoo, mild detergent, or a mild cleaning solvent.
• Avoid scrubbing and the use of harsh detergents.

Safety Precautions

1. Keep all hardware parts out of reach of children and animals.
2. Dispose of plastic packaging material immediately to avoid any risk of suffocation.

Parts Checklist

The following parts are included:

• Part 1: Bed Frame Side (Left) - 1 PC
• Part 2: Bed Frame Side (Right) - 1 PC
• Part 3: Bed Frame Base - 1 PC
• Part 4: Bed Frame Base Support - 1 PC
• Part 5: Headboard - 1 PC
• Part 6: Slats Support - 1 PC
• Part 7: Bed Slats - 2 PCS
• Part 8: Packaging Box - 1 PC

Hardware Checklist

• A: M8x20 mm Bolts - 12 PCS
• B: Allen Wrench - 1 PC
• C: Cotton Felt - 8 PCS

Safety Notes

Before attaching the side rails, determine which side will have the safety guardrail. For the side without the guardrail: Position the side rail so that any pre-drilled holes face downward (toward the floor). This prevents children from inserting fingers into the holes.

Assembly Steps

Step 1

Attach the bed frame sides (1, 2) to the bed frame base (3) and base support (4) using bolts (A) and the Allen wrench (B). Ensure the pre-drilled holes for the guardrail are positioned correctly.

Step 2

Attach the other bed frame side (1) to the bed frame base (3) and base support (4) using bolts (A) and the Allen wrench (B).

Step 3

Attach the headboard (5) to the assembled bed frame using the provided hardware.

Step 4

Insert the slats support (6) into the designated slots on the bed frame.

Step 5

Place the bed slats (7) onto the slats support, ensuring they are evenly spaced. The bed is now ready for use as a floor bed.

Step 6

Attach the headboard (5) to the other end of the bed frame.

Step 7

Disassemble the bed by reversing the steps. To convert the bed, rotate one section 180 degrees.

Step 8

For safety, re-install the bed side rails with the holes facing downward toward the floor. The hole is at the top.

Step 9

Attach the bed side rails using bolts (A) and the Allen wrench (B). Ensure holes face downward. Rotate the slats 180 degrees.

Step 10

Attach the headboard (5) to the assembled bed frame.

Step 11

Place the bed slats (7) onto the slats support.

Step 12

The bed is now ready for use as a junior bed.

Missing Something?

We work very hard to ship a perfect product, but sometimes furniture or hardware go missing or get damaged in transit. Please contact us and we'll quickly make it right.

Need some help? Our support team is here for you.

• Teddy Bed Australia Support
  Email: Support@teddybed.com.au
  Website: www.teddybed.com.au
• Teddy Bed New Zealand Support
  Email: Support@teddybed.com
  Website: www.teddybed.co.nz