User Manual for Home Depot models including: NV039-DX, NV039-DX 48 Inch Bifold Barn Door, 48 Inch Bifold Barn Door, Bifold Barn Door, Barn Door
Setting this screw to a depth of approximately 9.5mm will ensure proper holding position. 3. Slide the door to the desired position on the track (Figure 6c).
Bifold Barn Door (48in/60in/72) User Manual cNV039-DX EZZZZZZcemen Please contact usPlease also tell us your "ORDER ID" we will solve the issue for you as soon as possible. Customer Service:(855)208-0668(MON-FRI 9:00am-5:00pm Eastern Time) or ^ZZ Hardware List x The instructions are general versions for reference only. The installation methods are basically the same. If you have any doubts, please contact customer service. x Carefully remove all the parts from the carton and place them individually on a softcloth to prevent scratches or other damage. x Carefully and strictly follow these assembly&installation instructions to ensure acompleted product as designed. A1 1 PC F 2 PCS B1 1 PC G A2 1 PC H B2 1 PC I C 6 PCS J D 24 PCS K E 4 PCS L 1 PC 4 PCS 2 PCS 2 PCS 4 PCS 8 PCS -1- Hardware List x The instructions are general versions for reference only. The installation methods are basically the same. If you have any doubts, please contact customer service. x Carefully remove all the parts from the carton and place them individually on a softcloth to prevent scratches or other damage. x Carefully and strictly follow these assembly&installation instructions to ensure acompleted product as designed. 4.68FT*4 M 8 PCS S 5.75FT*4 6.73FT*5 4.68FT*4 N 16 PCS T 5.75FT*4 6.73FT*5 O 1 PC U 5 PCS P 2 PC V 5 PCS Q 2 PCS W 5 PCS R 8 PCS X 1 PCS -2- Step 1 A1 B1 D D A1 B1 C Step 2 F A1 E E -3- Step 3 D D A2 B2 C Step 4 F A2 E E -4- Step 5 B2 A2 B1 A1 B2 A1 B1 A2 Final Assembly -5- Step 6 1.The position of the track center is equal to the height of the door plus 1.57in (40mm) (Figure 1) (this will leave approximately 9mm gap between the floor and the bottom of the door) 2. Use a high-quality pencil and gently draw a pencil line on the wall to indicate the center position of the fixed track (Figure 2). 3. Mark the line where the guide rail spacing holes are located, and drill the fastener holes in advance using a 0.354in (9mm) drill bit on the wall. 4. Install the guide rail using the provided self tapping screws, pipe clamps, and guide rail washers. Attention: Even if there is solid wood behind, do not directly install the guide rail gasket onthe gypsum board. Otherwise, the guide rail gasket may be compressed Crushed gypsumboard may cause malfunctions in the track system Figure 1 G From the bottom of the door to the center of the guide rail Door+1.57in c40mm T S W V Figure 2 0.354in 9mm) From doorto floorbottom H+1.93in (49mm) Floor to track center= Floor to doorHeight +1.93in (49mm) track center -6- Step 7 1.Install the hanging wheel according to the hole position.(Figure 3) Figure 3a H Figure 3b L N L M NM 2. install a sleeve at the bottom of the door (Fiaure 4), insert the sleeve. Figure 4 P -7- Step 8 1. install the bottom stopper, The position of this bottom stopper is crucial for the normaloperation of the double folding compartment door. Gently pull out the door insert thebottom stopper (Figure 5a) into the sleeve located at the bottom of the positioning doorand reposition the door. 2. Use a leveling tool and pencil to mark the front and outer edges of the foor on the bottomdoor panel of the door position (see Figure 5b) Figure 5a Figure 5b R RR R Q -8- Step 9 1. Lift the door up close to the wal, pull it forward, and connect it with the top connecting plate. The top of the door is equipped with fixed and adjustable rollers(See Figure 6a). (Ensure that the fixing screws on the side of the fixed roller and adjustablewheel are inserted into the slot) 2. Use the provided 2.5mm hex wrench to tighten the fixing screws to lock the adjustable meterscrew assembly on the top connecting plate (see Figure 6b).Setting this screw to a depth of approximately 9.5mm will ensure proper holding position. 3. Slide the door to the desired position on the track (Figure 6c) Figure 6a Figure 6b Figure 6c Step 10 1. Hang the roller on the guide rail and slide it to the appropriate position, then hook the backof the fixed bracket onto the back of the guide rail,Align the front screw hole with the rollerfor installation and fixation (Figure 7b) 2. Use a 13mm open-end wrench to tighten the M8 * 25mm screw between the roller and thefixed bracket (Figure 7c) 3. Use a 2.5mm hex wrench to tighten the fixing screws on the back of the bracket (Figure 7d) Figure 7a Figure 7b x2 x4 I K Figure 7c J I Figure 7d K -9- AFTER-SALES SERVICE CARD We sincerely thank you for trusting our service and our products, and may this product add enrichment to your home. We guarantee that the product has undergone strict quality inspection and meticulous packaging. If you encounter any issue regarding either shipping or the product, please feel free to contact us at any time. We'd be more than happy to serve you wholeheartedly. ·This manual contains important information and keep it properly. · Please avoid harsh, corrosive and abrasive cleaners. · Keep dry and avoid damp environments. Customer Service:(855)208-0668(MON-FRI 9:00am-5:00pm Eastern Time) or help@EverythingSupport.com If you have any questions or concerns please feel free to contact us. We're committed to providing our customers with the quality service. -10-Adobe PDF library 15.00 Adobe Illustrator 25.3 (Windows)