KVM Solutions - Technology leader made in Germany – IHSE
抱歉，站点已暂停
Home - IHSE
Kvm-tec.com: KVM Extender over IP - Matrix Switching Systeme
Instructions for kvm-tec models including: KT-6024L, MAXflex, Full HD KVM Extender, MAXflex Full HD KVM Extender, KT-6024L Full HD KVM Extender, KT-6024L MAXflex Full HD KVM Extender, HD KVM Extender, KVM Extender, Extender
Kvm-tec.com: MAXflex Support - Full HD KVM Extender
Kvm-tec.com: MAXflex - dual copper Full HD KVM Extender
File Info : application/pdf, 4 Pages, 1.80MB
DocumentDocumentkvm-tec Support support@kvm-tec.com Phone: +43 2253 81912 - 30 max flex kvm-tec First Aid MAXflex No Power (No LED) USB is not working No Video Video error (stripes in the picture) Check the powerplug Is the power supply ok? Try another Unit. Contact kvm-tec support Are the USB Devices plugged in correctly? Is the USB cable on the Local side plugged into the PC? Are the USB Devices working directly on the PC? Replace the USB cable from PC to the Local Extender Check if local and remote Unit have the same firmware Check if the local or the remote Unit is causing the problem by swaping first the local and than the remote Unit to another Unit Check if all cables are plugged in correctly Check if the PC is sending a Image by plugging in a monitor on the local out of the local Unit Check if the DDC is set correctly (in menu under point ,,O") Check if both Units have the correct firmware Contact kvm-tec support Check if all cables are plugged in correctly Check if the PC is sending a Image by plugging in a monitor on the local out of the local Unit Check if the DDC is set correctly (in the menu under point ,,o") Check if local and remote Unit have the correct firmware Check if the network switch is setup correctly and has enough bandwidth Check if other units have the same behaviour Contact kvm-tec support Contact kvm-tec support We are here for you to answer your questions about installation? Manual download www.kvm-tec.com or kvm-tec Installationchannel on our homepage personally +43 2253 81912 Misprints, errors and technical changes reserved MAXflex Dual copper KT- 6024L CPU/LOCAL KT - 6024R CON/REMOTE www.kvm-tec.com V10522 Check out our Installation Channel: kvm-tec Quick Instruction Power plug 12V 1A (redundant) 12V 1A Power plug Delivery Content LOCAL/CPU Unit 1 x MA2 local (CPU) 1 x wall power supplyl 12V 1A (INT or EU-plug) 2 x DVI - DVI cable 1,8m/5.9ft 1 x USB cable 1,8m/5.9ft 4 x rubber feet REMOTE/CON Unit 1 x MA2 remote (CON) 1 x wall power supplyl 12V 1A (INT orEU-plug) 4 x rubber feet Open OSD menu The OSD main menu is opened with the standard shortcut: 5 x ALT Gr (Attention: the first 20 seconds 5 x Scroll always works, in case the shortcut was forgotten.) Switching list : CTRL+ALT+PRINT Changing the shortcuts in the OSD menu Go to the Remote Settings and then navigate to Keyboard Shortcut. Audio to speaker RS232 plug DVI in 2 from PC DVI in 1 from PC USB to PC Audio from PC Audio to PC RS232 plug Audio from microphone Power plug 12V 1A Power plug 12V 1A (redundant) USB from DVI to Keyboard Monitor 2 and mouse DVI to Monitor 1 Network cable CAT5e6/7/ up to 150m/492ft - main link Network cable CAT5e/6/7/ up to 150m/492ft Quick Installation Maxflex Dual local / CPU remote / CON 1. Connect the CON / Remote and the CPU / Local Unit to the included 12V 2A power supply. 2. Now connect the USB cable to a USB port on your PC and connect the other end of the USB cable to the CPU / Local Unit. Connect keyboard and mouse to the CON / Remote Unit. 3. Connect the CPU / Local and the CON / Remote Unit with a network cable. 4. Now connect the DVI cable to the DVI socket of the PC and the other end to the DVI socket of the CPU / Local Unit (PC-in). 5. Now connect the DVI cable to the DVI socket of the PC and the other end to the DVI socket of the CPU / Local Unit (PC-in 2). Then connect the monitor with the DVI cable to the CON / Remote Unit. 6. Connect PC audio/out with the audio cable to local audio/in. Connect audio/out via the audio cable 7. Almost done! Connect the audio cable local audio/out to the PC Audio in and remote audio/in with audio cable to the microphone 8. Using a switch: Connect all endpoints to the switch. Ensure that all connections have a bandwith of 1Gbit/sec. For video sharing the network has to support IGMP snooping. Have fun - your kvm-tec Extender is now in use for many years (MTBF approx.10 years) Misprints, errors and technical changes reserved USING THE ON SCREEN MENU Use the monitor and keyboard to use the main menu. To access the main menu: 1. Make sure the extenders, the monitors and the computer are switched on. 2. Press the ALT+GR key on your keyboard quickly five times. The main menu appears with an overview of the sub-menus. 3 To open a sub-menu press the applicable key. Main Menu Main meu Short Cuts : S Status Overview U Update Flash FW F Features Overview D DDC Option L Local Settings R Remote Settings A About Overview Q Exit Menu Status /current status Firmware Updates Settings Features DDC Option Fix settings 1020 x 1080 Settings Local Settings Remote Overview Upgrades Upgrades Exit Misprints, errors and technical changes reserved SYSTEM STATUS Single Dual In the status overview menu the current status of the extender connection is displayed. It provides information on the connection itself as well as resolution of the video channel, and USBstatus. The enabled options and the current firmware-version is displayed in the left top corner. Link status shows whether there is a physical connection available. Connected indicates if kvm data is currently able to be transmitted. Video and USB show if data is currently being transmitted. VIEWING THE FIRMWARE VERSION Under,,A" - About the currently installed firmware version of the remote (CON) and local (CPU) Extender is displayed (e.g. ,4267`) FEATURES MENÜ POINT TO POINT You can switch the Point to Point mode on and off by pressing the ,,P" key ATTENTION - if the point to point mode is activated, the switching mode cannot be activated Features Menu P Point to Point Mode M Matrix Switching Mode D Freeze last Image E USB Emulation Mode S USB Save Feature O Power Redundance Alert C Diagnosis U Unlock Features I IP Management Enabled/Disabled (Point to Point Point to Point excludes itself with Matrix mode Disabled/Enabled (Disabled)Disabled/Enabled (Disabled ) Disabled/Enabled (mass storage usable) Disabled/Enabled Alert System Diagnosis menu Unlock Features IP Management Misprints, errors and technical changes reserved MATRIX SWITCHING MODE By pressing the ,,M" button you can switch the Matrix Switching Mode off and on KVM-TEC Gewerbepark Mitterfeld 1 A 2523 Tattendorf Austria www.kvm-tec.com IHSE GmbH Benzstr.1 88094 Oberteuringen Germany www.ihse.com IHSE USA LLC 1 Corp.Dr.Suite Cranburry NJ 08512 USA www.ihseusa.com IHSE GMBH Asia 158Kallang Way,#07-13A 349245 Singapore IHSE China Co.,Ltd Room 814 Building 3, Kezhu Road Guangzhou PRC www.ihse.com www.ihse.com.cn