Instruction Manual for MDT models including: SCN-GLED1W.01 Glass KNX LED Indicator, SCN-GLED1W.01, Glass KNX LED Indicator, KNX LED Indicator, LED Indicator, Indicator
MDT KNXperts – KNX Smart Home - Assembly and Operation Instructions
MDT Glas LED Anzeige schwarz ab € 127,06 (2022) | Preisvergleich Geizhals Österreich
MDT Glas LED Anzeige 55 ab € 109,20 (2024) | Preisvergleich Geizhals Österreich
File Info : application/pdf, 2 Pages, 307.88KB
DocumentDocumentTechnische Daten LED Anzeige - Technical Data LED Indicator Technische Daten Technical Data Spezifikation KNX Schnittstelle Specification KNX interface Verfügbare KNX Datenbanken Available application software Max. Kabelquerschnitt Permitted wire gauge KNX Busklemme KNX busconnection terminal Versorgungsspannung Power Supply Leistungsaufnahme KNX Bus typ. Power consumption KNX bus typ. Umgebungstemperatur Operation temperature range Schutzart Enclosure Abmessungen (B x H xT) Dimensions (W x H x D) SCN-LED55.01 TP-256 ETS 3/4/5 0,8mm Ø, solid core KNX Bus < 0,3W 0 bis + 45°C IP 20 41mm x 41mm x 13mm SCN-GLED1W.01 SCN-GLED1S.01 TP-256 ETS 3/4/5 0,8mm Ø, solid core KNX Bus < 0,3W 0 bis + 45°C IP 20 92mm x 92mm x 13mm ® Betriebsanleitung LED Anzeige nur für autorisiertes Elektrofachpersonal Operating Instructions LED Indicator for authorised electricans Allgemeine Sicherheitshinweise - Important safety notes Lebensgefahr durch elektrischen Strom - Danger High Voltage · Das Gerät darf nur von Elektrofachkräften montiert und angeschlossen werden. Beachten sie die länderspezifischen Vorschriften sowie die gültigen KNX-Richtlinien. Die Geräte sind für den Betrieb in der EU zugelassen und tragen das CE Zeichen. Die Verwendung in den USA und Kanada ist nicht gestattet. Installation and commissioning of the device only be carried out by authorised electricans. The relevant standards, directives, regulations and instructions must be observed. The devices are approved for use in the EU and have the CE mark. Use in USA and Canada is prohibited. Anschlussklemmen, Bedien- und Anzeigeelemente LED Indicator Terminals, Operating and Display LED Indicator SCN-LED55.01 SCN-GLED1W.01 4 SCN-GLED1S.01 4 MDT technologies GmbH · 51766 Engelskirchen · Papiermühle 1 Tel.: + 49 - 2263 - 880 · Fax: + 49 - 2263 - 4588 · knx@mdt.de · www.mdt.de Stand: 0422 2 31 21 21 4 4 Alle roten LEDs der Sensorflächen dienen All red LEDs behind the sensor areas are als Programmier LED. Diese blinken im used as programming LED. They are Wechsel von links nach rechts. blinking alternately from the left to the right side. 1 - Busanschlussklemme 3 - Rote Programmier LED (SCN-LED55.01) - KNX busconnection terminal - Red programming LED (SCN-LED55.01) 2 - Programmiertaster - Programming key 4 - Rote Programmier LED (SCN-GLED1x.01) - Red programming LED (SCN-GLED1x.01) Technische Änderungen und Irrtümer vorbehalten, Abbildungen können abweichen. Montage und Anschluss LED Anzeige - Installation LED Indicator 1. Schließen Sie die LED Anzeige am KNX Bus an. Connect the LED Indicator to the KNX bus. 2. Einbau der LED Anzeige in die Schalterdose. Flush mounting of the LED Indicator. 3. Busspannungsversorgung zuschalten. Switch on KNX power supply. Anschlussbeispiel SCN-LED55.01 / SCN-GLEDx.01 - Exemplary circuit diagram SCN-LED55.01 / SCN-GLEDx.01 Inbetriebnahme LED Anzeige - Commissioning LED Indicator Hinweis: Die Produktdatenbank finden Sie unter www.mdt.de/Downloads.html Note: Before commisioning please download application software at www.mdt.de/Downloads.html 1. Physikalische Adresse vergeben und Applikationsprogramm in der ETS erstellen. Assign the physical address and set parameters with the ETS. 2. Laden Sie die Physikalische Adresse und das Applikationsprogramm in die LED Anzeige. Drücken Sie den Programmiertaster wenn Sie dazu aufgefordert werden. Upload the physical address and parameters into the LED Indicator. After request press programming button. 3. Die rote LED erlischt nach erfolgreicher Programmierung. After sucessfull programming the red LED turns off. MDT technologies GmbH · 51766 Engelskirchen · Papiermühle 1 Tel.: + 49 - 2263 - 880 · Fax: + 49 - 2263 - 4588 · knx@mdt.de · www.mdt.de Stand: 0422 Beschreibung LED Anzeige - Description LED Indicator Die MDT LED Anzeige dient zum Visualisieren von Verknüpfungen und Gebäudefunktionen. Folgende Funktionen sind in parametrierbar: · 12 unabhängige voneinander schaltbare RGB LEDs · 3 Objekte je LED · 5 Zustände je LED parametrierbar (Wert=0, Wert=1, 2 Prioritätsobjekte, Ausfall des Objekts) z.B.: Garagentor zu: grün, Garagentor auf: rot, Garagentor fährt auf: rot blinkend, Garagentor fährt zu: grün blinkend · 8 Logikblöcke mit je 8 Eingängen · 4 Module zum Vergleichen von Telegrammen · 2 Helligkeitsstufen · Tag-/Nachtobjekt · Abschaltung/Reduzierung der Helligkeit · Anwesend/Abwesend Objekt · Ausfallüberwachung der Objekte mit Meldeobjekt · Meldeobjekt (z.B. Abwesend und Fenster geöffnet) Passend für 55 Schalterprogramme z.B.: · GIRA Standard 55, E2, E22, Event, Esprit · JUNG A500, Aplus, Acreation, AS5000 · BERKER S1, B3, B7 glass · MERTEN 1M, M-Smart, M-Plan, M-Pure Die MDT LED Anzeige ist zur Installation in Schalterdosen vorgesehen. Die Montage muss in trockenen Innenräumen erfolgen. Lieferung der Unterputzgeräte erfolgt mit Montagetragring. The MDT LED Indicator allows to display universal logical and building functions. These functions are available. · 12 independently switchable RGB LED · 3 objects for each LED · 5 states for each LED possible (value=0, value=1, 2 priority objects, failure of an object) e.g.: Garage door closed: green, Garage door opened: red, Garage door moves up: red flashing, Garage door moves down: green flashing · 8 logical blocks with 8 inputs each (8 objects) · 4 modules to compare telegrams · Brightness in 2 steps adjustable · Day/night object · Deactivation/reduction of the brightness · Presence/absence object · Drop out monitoring for objects with report function · Object with report function (e.g. absence or window opened) Fits 55mm systems/ranges: · GIRA Standard 55, E2, E22, Event, Esprit · JUNG A500, Aplus, Acreation, AS5000 · BERKER S1, B3, B7 glass · MERTEN 1M, M-Smart, M-Plan, M-Pure The MDT LED Indicator is a flush mounted device for fixed installations in dry rooms, it is delivered with support ring. Technische Änderungen und Irrtümer vorbehalten, Abbildungen können abweichen.