Global leading LED display control solution
Instruction Manual for VISUAL LED models including: Nova LCT Windows PC Screen Configuration, Nova LCT, Windows PC Screen Configuration, PC Screen Configuration, Screen Configuration, Configuration
Manuali - Visual Led
File Info : application/pdf, 19 Pages, 3.06MB
DocumentDocumentWINDOWS PC SCREEN CONFIGURATION MANUAL WITH NOVA LCT ENGLISH CONFIGURATION MANUAL INDEX INDEX - CONFIGURATION STEPS READ THIS MANUAL AND FOLLOW THIS STEPS IN ORDER WIRING AND CONNECTIONS 1 1.A NETWORK CONNECTION WITH ETHERNET CABLES 1.B WI-FI ACCESS POINT CONNECTION SOFTWARE DOWNLOAD AND INSTALLATION 2 2.1 DOWNLOAD AND INSTALL NOVALCT LOGIN TO THE CONTENT PLAYER FROM NOVALCT 3 3.1 LOGIN TO THE CONTENT PLAYER 3.2 ACCESS TO SCREEN CONFIGURATION RECEIVING CARD CONFIGURATION 4 4.1 IDENTIFY THE POSITION OF YOUR LED CABINETS 4.2 LOADING THE CONFIGURATION FILE 4.3 SENDING THE NEW CONFIGURATION TO THE SCREEN SCREEN CONNECTION CONFIGURATION 5 5.1 EXAMPLE OF CONNECTION SETTINGS 5.2 SETTING THE NUMBER OF CABINETS FOR YOUR DISPLAY 5.3 CONFIGURE DATA WIRING CONNECTIONS 5.4 SENDING THE CONFIGURATION TO THE SCREEN 5.5 BACKUP FILE OF THE SCREEN CONNECTION CONFIGURATION MANUAL 1. WIRING AND CONNECTIONS STEP 1: WIRING AND CONNECTIONS THERE ARE 2 WAYS TO CONNECT YOUR LED DISPLAY WITH THE CONTENT PLAYER AND YOUR PC. CHOOSE ONE OF THE FOLLOWING CONNECTION METHODS (A OR B). VISUAL LED DISPLAY 1.A - NETWORK CONNECTION WITH ETHERNET CABLES (RECOMMENDED) STANDARD NETWORK CABLE STRAIGHT FROM THE LED OUT PORT OF THE CONTROLLER TO THE FIRST LED DISPLAY FRAME WINDOWS PC WITH WINDOWS 10 OR HIGHER THERE MUST NOT BE ANY ROUTER OR SWITCH BETWEEN THE PLAYER AND THE SCREEN CONTENT PLAYER STANDARD NETWORK CABLE FROM YOUR PC TO YOUR ROUTER STANDARD NETWORK CABLE FROM YOUR ROUTER TO THE ETHERNET PORT OF THE CONTENT PLAYER CONFIGURATION MANUAL 1.B - WI-FI ACCESS POINT CONNECTION VISUAL LED DISPLAY 1. WIRING AND CONNECTIONS STANDARD NETWORK CABLE STRAIGHT FROM THE LED OUT PORT OF THE CONTROLLER TO THE FIRST LED DISPLAY FRAME THERE MUST NOT BE ANY ROUTER OR SWITCH BETWEEN THE PLAYER AND THE SCREEN CONTENT PLAYER PC WITH WINDOWS 10 OR HIGHER CHECK THE SIDE STICKER ON THE CONTENT PLAYER WITH THE WI-FI ACCESS POINT NAME AND PASSWORD. CONNECT YOUR PC TO THE CONTENT PLAYER'S WI-FI ACCESS POINT CONFIGURATION MANUAL 1. WIRING AND CONNECTIONS 1: CLICK ON THE WIRELESS NETWORKS ICON IN THE LOWER RIGHT CORNER OF YOUR PC'S DESKTOP. 2: SELECT THE BUTTON TO MANAGE WIFI CONNECTIONS 3: A LIST OF WI-FI NETWORKS DETECTED BY YOUR PC WILL BE DISPLAYED. 4: CHECK FOR THE NETWORK CALLED APXXXXXXXX (THE EXACT NAME IS ON THE STICKER ON THE SIDE OF THE CONTENT PLAYER) AND CLICK ON "CONNECT" 5: TYPE THE WI-FI PASSWORD (12345678 BY DEFAULT) AND CICK "NEXT". 6: NOW YOU ARE DIRECTLY CONNECTED TO THE CONTENT PLAYER OF YOUR LED DISPLAY CONFIGURATION MANUAL 2. SOFTWARE DOWNLOAD AND INSTALL STEP 2: SOFTWARE DOWNLOAD AND INSTALLATION 2.1 DOWLOAD AND INSTALL NOVALCT VISIT NOVASTAR'S WEBSITE (HTTPS://WWW.NOVASTAR.TECH) AND GET TO THE DOWNLOADS SECTION DOWNLOAD THE LATEST VERSION OF NOVALCT FROM THE "SOFTWARE" TAB IN THE DOWNLOAD SECTION. INSTALL NOVALCT FOLLOWING ALL DEFAULT INSTRUCTIONS. THE INSTALLATION OF NOVALCT MAY TRIGGER ADDITIONAL SOFTWARE AND DRIVERS INSTALLATIONS FOR A CORRECT DETECTION OF THE LED DISPLAY. ALLOW EVERY STEP. CONFIGURATION MANUAL 3. LED SCREEN CONFIGURATION STEP 3: LOGIN TO THE CONTENT PLAYER FROM NOVALCT 3.1 - LOGIN TO THE CONTENT PLAYER RUN NOVALCT AND ALLOW ANY NETWORK ACCESS PERMISSION. CLICK ON THE "USER" MENU AND SELECT "MEDIA PLAYER LOGIN". USER: admin PASSWORD: 123456 YOUR PLAYER WILL APPEAR IN THE TERMINALS LIST AS TAURUSXXXXXXXXX. SELECT THE PLAYER AND CLICK ON "CONNECT SYSTEM" USING THESE CREDENTIALS: ADMIN / 123456 IF THE PLAYER DOES NOT APPEAR, PLEASE NOTE THAT IT MAY TAKE 1 OR 2 MINUTES FOR THE PLAYER TO BE DETECTABLE AFTER IT IS TURNED ON. IF IT STILL DOES NOT APPEAR, CHECK ALL CONNECTIONS, UNPLUG THE PLAYER AND PLUG IT AGAIN. WAIT 2 MINUTES AND CLICK "REFRESH" TO FORCE DETECTION. CONFIGURATION MANUAL 3. LED SCREEN CONFIGURATION IF THE LOGIN TO THE PLAYER IS CORRECT THE SOFTWARE WILL SHOW NEW BUTTONS LOOKING LIKE THE IMAGE BELOW. 3.2 - ACCESS TO SCREEN CONFIGURATION CLICK ON "SCREEN CONFIGURATION" AND SELECT THE COMMUNICATION PORT CORRESPONDING TO YOUR PLAYER AND THEN CLICK ON NEXT CONFIGURATION MANUAL 4. RECEIVING CARD CONFIGURATION STEP 4: RECEIVING CARD CONFIGURATION 4.1 - IDENTIFY THE POSITION OF YOUR LED CABINETS IF YOUR DISPLAY IS ASSEMBLED WITH VERTICAL CABINETS YOU CAN SKIP THIS SECTION AND GO TO STEP 5. THE RECEIVING CARD IS ALREADY CONFIGURED FOR THE VERTICAL POSITION. VERTICAL CABINET HORIZONTAL CABINET IF YOUR DISPLAY IS ASSEMBLED WITH HORIZONTAL CABINETS, YOU MUST REQUEST YOUR CONFIGURATION FILE BY EMAIL AT SOPORTE@VISUALLED.COM AND FOLLOW THE STEPS IN THIS SECTION. YOU WILL HAVE TO CHOOSE ONE OF THE 2 FILES DEPENDING ON HOW YOU HAVE MOUNTED YOUR CABINETS HORIZONTALLY: 90 DEGREES 270 DEGREES CABINET STATUS LEDS ON THE RIGHT SIDE CABINET STATUS LEDS ON THE LEFT SIDE THE ROTATION OF THE CABINETS IS ALWAYS COUNTED CLOCKWISE AND FROM A FRONT VIEW OF THE DISPLAY CONFIGURATION MANUAL 4. RECEIVING CARD CONFIGURATION 4.2 - LOADING THE RECEIVING CARD CONFIGURATION FILE FOR HORIZONTAL CABINETS USE THE FILE PROVIDED BY VISUAL LED ACCORDING TO THE ROTATION (90º / 270º) OF THE CABINETS ON YOUR DISPLAY. A: AT THE BOTTOM OF THE WINDOW, CLICK ON THE "LOAD FROM FILE" BUTTON. A WINDOW TO OPEN AN RCFGX FILE WILL APPEAR. A SELECT THE RCFGX FILE SUPPLIED FOR YOUR SCREEN AND CLICK ON OPEN AFTER LOADING THE FILE, THE RESOLUTION IN PIXELS OF A CABINET WILL BE UPDATED IN THE WIDTH AND HEIGHT SECTION. IT IS INDIFFERENT WHETHER IT APPEARS AS "REGULAR" OR "IRREGULAR". 4.3 - SENDING THE NEW CONFIGURATION TO THE SCREEN B: AT THE BOTTOM, CLICK ON THE "SEND TO RECEIVING CARD" BUTTON. THE "SEND PARAMETERS" WINDOW WILL APPEAR B CONFIGURATION MANUAL 4. RECEIVING CARD CONFIGURATION C: SELECT THE CHECKBOX "RESET STARTING COORDINATE..." AND CLICK ON SEND. WAIT UNTIL YOU RECEIVE A CONFIRMATION MESSAGE. C D: CLICK ON SAVE, WAIT FOR ANOTHER CONFIRMATION MESSAGE. D E: CANCEL THE BACK UP E CONFIGURATION MANUAL 5. SCREEN CONNECTION STEP 5: SCREEN CONNECTION CONFIGURATION 5.1 - EXAMPLE OF CONNECTION SETTINGS (CONNECTION TAB OF THE DISPLAY...) IN THIS SECTION WE CONFIGURE THE POSITION OF THE CABINETS AND THE THE DATA WIRING OF THE SCREEN. AS AN EXAMPLE WE ARE GOING TO CONFIGURE A SCREEN WITH 8 CABINETS POSITIONED IN 2 ROWS OF 4. SINGLE CABINET BASED ON THIS EXAMPLE YOU CAN CONFIGURE THE NUMBER OF CABINETS CORRESPONDING TO THE SIZE OF YOUR SCREEN. CONFIGURATION MANUAL 5. SCREEN CONNECTION 5.2 - SETTING THE NUMBER OF CABINETS FOR YOUR DISPLAY IN THE "SCREEN CONNECTION" TAB, CLICK ON THE "CONFIGURE" BUTTON IN THE UPPER RIGHT CORNER. A: SELECT THE "STANDARD SCREEN" OPTION AT THE TOP OF THE SCREEN. B: ON RECEIVING CARD SIZE, CHECK THAT THE WIDTH AND HEIGHT NUMBERS ARE THE SAME THAT APPEAR B ON THE SENDING CARD TAB: CABINET INFORMATION. IF THEY ARE NOT TYPE IN THE PIXEL WIDTH AND HEIGHT TO MATCH IT. IN CASE THEY DO NOT MATCH, MODIFY THESE NUMBERS AND CLICK ON THE "APPLY TO ROW" AND "APPLY TO COLUMN" BUTTONS. CONFIGURATION MANUAL C: GO TO THE "COLUMNS" BOX AND TYPE IN THE NUMBER OF COLUMNS CORRESPONDING TO HOW YOUR SCREEN IS SET UP. ACCORDING TO OUR EXAMPLE WE WILL ENTER 4. 5. SCREEN CONNECTION C D: GO TO THE "ROWS" BOX AND TYPE IN THE NUMBER OF ROWS CORRESPONDING TO HOW YOUR SCREEN IS SET UP. ACCORDING TO OUR EXAMPLE WE WILL ENTER 2. D AFTER ENTERING THE NUMBERS OF COLUMNS AND ROWS, WHITE RECTANGLES WILL APPEAR REPRESENTING THE CABINETS THAT MAKE UP OUR DISPLAY. ADAPT THE NUMBER OF ROWS AND COLUMNS TO FIT YOUR OWN LED DISPLAY. CONFIGURATION MANUAL 5. SCREEN CONNECTION 5.3 - CONFIGURE DATA WIRING CONNECTIONS BEFORE WE BEGIN, LET'S TAKE A LOOK AT THE BACK VIEW OF THE DATA WIRING OF OUR EXAMPLE DISPLAY. THE DATA ENTERS THROUGH THE LOWER LEFT CABINET. REAR VIEW OF OUR EXAMPLE DISPLAY CONTENT PLAYER NETWORK CABLE IMPORTANT: IN NOVALCT WE WILL SHOW THE DISPLAY DATA WIRING FROM A FRONT VIEW. THEREFORE, THE DATA WIRING ENTERS FROM THE LOWER RIGHT FRAME. FRONT VIEW OF OUR EXAMPLE DISPLAY CONTENT PLAYER NETWORK CABLE CONFIGURATION MANUAL 5. SCREEN CONNECTION NOW WE WILL SET HOW THE SCREEN IS WIRED. WE WILL WORK WITH THE MOUSE BY CLICKING ON THE WHITE FRAMES TO SET THE PATH OF THE SCREEN DATA WIRES. IMPORTANT: THIS CONFIGURATION SCREEN REPRESENTS THE CABINETS FROM A FRONT VIEW. IF AT ANY TIME DURING THIS PROCESS WE MAKE A MISTAKE, WE CAN UNDO THE WIRING ORDER BY CLICKING ON THE FRAMES WITH THE RIGHT MOUSE BUTTON. THERE IS ALSO A "RESET" BUTTON TO RESTART THE WIRING. WE MUST ALWAYS START BY CLICKING ON THE CABINET WHERE THE DATA ENTERS THE SCREEN FROM A FRONT VIEW. IN OUR EXAMPLE IS THE LOWER RIGHT OF THE DIAGRAM. IT WILL LIGHT UP IN PINK. THEN WE CLICK ON THE NEXT CABINET OF THE SAME ROW FOLLOWING THE PATH OF THE DATA CABLES ON THE SCREEN THIS WILL ALSO LIGHT UP PINK AND A LETTER E (END) WILL APPEAR INDICATING THAT IT IS THE LAST CABINET IN THE CIRCUIT AT THIS TIME. A LETTER S (START) WILL APPEAR ON THE FIRST CABINET INDICATING THAT IT IS THE FIRST CABINET IN THE CIRCUIT. CONFIGURATION MANUAL 5. SCREEN CONNECTION NOTE THAT IN A HORIZONTALLY ASSEMBLED DISPLAY THE WIRING CIRCUIT WILL BE DIFFERENT (IT WILL PROBABLY GO FROM BOTTOM TO TOP IN COLUMNS). WE CLICK IN ORDER ON THE CABINETS OF THE LOWER ROW FOLLOWING THE WIRING. WHEN WE REACH THE END OF THE ROW WE CLICK ON THE TOP CABINET FOLLOWING THE PATH OF THE NETWORK CABLES ON THE SCREEN. CONTINUE CLICKING IN ORDER ON THE CABINETS UNTIL THE TOP ROW IS COMPLETED. CONFIGURATION MANUAL 5. SCREEN CONNECTION 5.4 - SENDING THE CONFIGURATION TO THE SCREEN AFTER DRAWING THE DATA WIRING ON THE CABINETS, WE WILL SEND THIS CONFIGURATION TO THE SCREEN. B: A CONFIRMATION WINDOW WILL APPEAR: CLICK OK C A A: CLICK ON THE "SEND TO HW" BUTTON. B C: WHEN THE CONNECTIONS MAP IS SENT, A CONFIRMATION MESSAGE WILL POP UP. CLICK OK D: CLICK ON THE "SAVE" BUTTON AND WAIT FOR ANOTHER CONFIRMATION MESSAGE ACCEPT THE CREATION OF A CONFIGURATION BACKUP D CONFIGURATION MANUAL 5. SCREEN CONNECTION AFTER THIS STEP YOU SHOULD BE ABLE TO CORRECTLY VIEW THE DEFAULT CONTENTS LOADED IN THE NOVASTAR PLAYER. 5.5 - BACKUP FILE OF THE SCREEN CONNECTION CONFIGURATION FINALLY WE WILL MANUALLY SAVE A BACKUP FILE OF THE DATA WIRING CONFIGURATION E E: CLICK ON THE "SAVE TO FILE" BUTTON. A WINDOW TO SAVE THE WIRING BACKUP FILE WITH .MAP EXTENSION WILL APPEAR. SAVE IT IN THE SAME FOLDER AS YOUR RECEIVING CARD FILE YOU HAVE NOW SUCCESSFULLY CONFIGURED YOUR LED DISPLAY. YOU CAN CLOSE THIS CONFIGURATION WINDOW AND THE NOVALCT PROGRAM, THIS SOFTWARE IS ONLY USED FOR THE CONFIGURATION OF THE DISPLAY. NOT ALL FUNCTIONS OF THIS SOFTWARE ARE COMPATIBLE WITH ALL DISPLAYS. AFTER A CORRECT CONFIGURATION YOU CAN UNINSTALL IT FROM YOUR SYSTEM.