OVE SMART TOILET

WATCH OUR YOUTUBE INSTALLATION VIDEO

https://youtu.be/Fitsmm5qjcM

Dimensions are approximately:

• Height: 23 inches (585 mm)
• Width: 12 inches (305 mm)
• Length/Depth: 16-9/16 inches (420 mm) from front to back
• Overall Height (back): 29-1/8 inches (740 mm)

Thank you for choosing OVE SMART TOILET. Please read and understand this entire manual before attempting to assemble, operate or install this product.

CONTENT

• SAFETY NOTICE
• WARNINGS
• PART LIST
• INSTALLATION INSTRUCTIONS
• FIRST TIME USE
• CONTROLS DESCRIPTION
• FEATURES
• INTELLIGENT FEATURES
• CLEANING THE FILTER
• LONG TERM STORAGE
• NOZZLE MAINTENANCE
• SPECIFICATION SHEET
• MAINTENANCE & CONSUMER RESPONSIBILITIES
• LIMITED 1 YEAR WARRANTY
• INFORMATION ABOUT YOUR WARRANTY COVERAGE
• NOTES ON WARRANTY
• FOR WARRANTY SERVICE
• INSTALLATION PICTURE
• CONTACT US

SAFETY NOTICE

[!] ATTENTION! BEFORE INSTALLING THE PRODUCT, YOU MUST READ AND UNDERSTAND CAREFULLY ALL BELOW WARNINGS.

1. It is forbidden to disassemble the toilet by yourself.
2. Do not place this product in a wet place as it is an electronic product. Ensure proper air flow if installed in a bathroom.
3. Ensure the product is placed more than 0.6 meters away from the bathtub.
4. Ensure the electric power is AC 120V and the electrical socket can handle a load of 500W power to prevent fire or electrical shock.
5. Ensure the electrical source is well grounded.
6. Do not apply water or detergent on the product or its electrical plug.
7. Do not touch the electrical plug with a wet hand, as it can cause fire or electric shock.
8. Do not use the product if it exhibits the following problems. If any occur, turn off the electricity and close the water valve:
   • Water leaking from the pipe or the main body.
   • Crack or breakage.
   • Abnormal sound or smell.
   • Smoke coming out from the product.
9. Keep flames or flammable products away from the toilet.
10. Do not step on the toilet seat, seat cover, or main body, nor place heavy objects on the product. This could cause breakage, injury, or indoor flooding.
11. Do not insert fingers or other objects into the drying blower outlet.
12. Do not touch or cover the drying blower outlet with clothes, as it may lead to burn injury or electric shock.
13. Do not tightly bend or press the flexible supply hose, as it may lead to water leakage or reduced water pressure.
14. Clean the product with soft cleaning products.
15. Do not use harsh detergents for cleaning.
16. Do not dispose of anything other than toilet paper into the toilet to prevent blockages and indoor flooding.
17. Be careful not to let objects like combs, toothbrushes, or other items fall into the toilet.

WARNINGS

PART LIST

The following components are included:

INSTALLATION INSTRUCTIONS

1. Step 1: Water Supply & Drain Alignment
   Ensure your water inlet pipe and floor discharge drain are installed according to the drawing. These are minimum measurements; installation is possible if your actual measurements are longer. TIP: Align masking tape with the center of the drain to help position the toilet.

2. Step 2: Floor Flange Installation
   Install the floor flange according to the manufacturer's recommendations. Ensure it is flush with the floor. An improperly flushed flange may result in inadequate installation.

3. Step 3: Fixing Bolt Positioning
   Position the two fixing bolts of the floor flange correctly.

4. Step 4-8: Seat Removal (Optional)
   These steps detail how to remove the toilet seat from the ceramic base to facilitate alignment with floor flange bolts and tightening nuts. This is optional if nuts can be tightened from behind the toilet. To remove the seat, unscrew the two small screws on each side. Flip the seat cover gently and rest it on the bowl, being careful not to pull connected wires. Remove the water tank lid and unscrew the bolts inside the tank. With care, remove the whole tank and seat from the ceramic base, setting them aside on a soft surface.

5. Step 9: Seal Ring Placement
   Place the seal ring under the toilet.

6. Step 10: Toilet Positioning & Bolt Alignment
   Position the toilet onto the floor flange, ensuring the fixing bolts align with the toilet's holes.

7. Step 11: Washer and Nut Installation
   Install the washers and nuts onto the two fixing bolts of the floor flange.

8. Step 12: Tightening Bolts
   Using a ratchet, tightly screw the nuts to the fixing bolts. With care, re-install the tank and seat onto the ceramic base.

9. Step 13: Water Inlet Connection
   Connect the water inlet hose to your existing shut-off valve on the wall. Then, connect the other end of the hose to the toilet's water inlet located at the back, underneath the filter.

10. Step 14: Silicone Application & Drying
    Apply silicone around the base of the toilet. Wait for 24 hours for it to dry.

FIRST TIME USE

1. Open the water supply shut-off valve.
2. Plug the toilet into the power socket.
3. The toilet will turn ON automatically. Lights will blink circularly from left to right, followed by a short beep upon completion of the first cycle. This indicates the bidet water tank is filling and the seat/cleaning water are warming up. A sensor will stop filling after approximately 30 seconds when the tank is full.
4. Once beeping and flashing lights stop, the toilet is ready for use.

Notice:

• Warming up the toilet seat and bidet water tank takes about 5 minutes.
• Leave the power continuously ON to ensure all functions are ready for immediate use.
• If the toilet is not used for 5 days, it will automatically drain and power off.

CONTROLS DESCRIPTION

SIDE CONTROL PANEL

• POWER: Pressing this key stops any ongoing function. Pressing for 3 seconds turns the power ON/OFF.
• SPRAY/MOVE: Initiates Static Spray Cleaning. Pressing again changes to Back-&-Forth Spray Cleaning. (SPRAY refers to 1 water jet function).
• DRYING: Initiates Static Air Drying. Pressing for 5 seconds while not seated turns AUTOMATIC DRYING ON/OFF.
• BIDET/MOVE: Initiates Static Bidet Cleaning. Pressing again changes to Back-&-Forth Bidet Cleaning. (Bidet refers to 4 water jets function).

LIGHT INDICATOR PANEL

• POWER indicator: RED when ON, OFF when powered OFF.
• ECO MODE indicator: GREEN when active, OFF when not active.
• WATER HEATING indicator: RED when active, RED when not active.
• SEAT HEATING indicator: RED when active, RED when not active.
• SEAT SENSOR indicator: RED when active, OFF when not active.

BEEPING SOUNDS DIRECTIONS

• LONG BEEPING: Indicates successful command reception.
• SHORT BEEPING: Indicates unsuccessful command reception.

REMOTE CONTROL

• POWER: Stops ongoing function; press for 3 seconds to turn ON/OFF.
• ECO MODE: Turns ECO MODE ON/OFF.
• FLUSH: Flushes the toilet. Press for 5 seconds to turn AUTOMATIC FLUSHING OFF; press again for 5 seconds to turn it ON.
• SPRAY/MOVE: Initiates Static Spray Cleaning; press again for Back-&-Forth Spray Cleaning (1 water jet).
• BIDET/MOVE: Initiates Static Bidet Cleaning; press again for Back-&-Forth Bidet Cleaning (4 water jets).
• MASSAGE SPRAY & NIGHT LIGHT: During Spray/Bidet cleaning, initiates Massage Spray. When not seated, turns Night Light ON/OFF.
• DRYING: Initiates Air Drying.
• WATER TEMP: Cycles through 4 temperature settings for water jets: Room temp, 34°C (93°F), 37°C (99°F), 40°C (104°F).
• AIR TEMP: Cycles through 4 temperature settings for air drying: Room temp, 40°C (104°F), 50°C (122°F), 55°C (131°F).
• SEAT TEMP: Cycles through 4 temperature settings for seat heating: Room temp, 34°C (93°F), 38°C (99°F), 42°C (108°F).
• UP & DOWN ARROWS: Increase or decrease water jet pressure (4 settings from low to high) during Spray or Bidet Cleaning.
• LEFT & RIGHT ARROWS (WHILE SEATED): Move the nozzle forward or backward (4 increments) during Static Spray or Static Bidet Cleaning.
• LEFT & RIGHT ARROWS (WHILE NOT SEATED): LEFT key opens/closes the cover. RIGHT key opens/closes the seat. Pressing RIGHT for 5 seconds turns AUTOMATIC OPEN/CLOSE SEAT ON/OFF.

FEATURES

• SPRAY CLEANING (1 WATER JET): Works only when seated. Press SPRAY/MOVE for cleaning. Press again for back-and-forth nozzle movement for thorough cleaning.
• BIDET CLEANING (4 JETS OF WATER): Works only when seated. Press BIDET/MOVE for cleaning. Press again for back-and-forth nozzle movement for thorough cleaning. Seat sensors prevent water/air spray when not seated. The nozzle self-washes before and after each use. Spray function stops automatically after approx. 1 minute due to bidet tank exhaustion; wait 30 seconds for refill. It takes about 10 seconds after pressing BIDET/MOVE or SPRAY/MOVE for water to spray.
• AIR DRYING: Works only when seated. Press DRYING key for air drying. If DRYING is pressed during flushing, wait approx. 10 seconds for warm air.
• POWER: The toilet turns OFF automatically if not used for 5 days. The toilet may spray for 1-2 seconds after standing up; press the STOP key before standing during cleaning.
• FLUSHING: Use the FLUSHING key to flush. A manual FLUSH BUTTON is also located on the right. The smart toilet cleans the bowl automatically after the user leaves. Long press the FLUSHING key to turn AUTOMATIC FLUSHING ON/OFF.
• MASSAGE SPRAY: Provides pleasant cleaning with a strong, intermittent single water jet.

SMART FEATURES

• ECO MODE: Reduces electricity usage during non-usage. Bidet water tank and seat heat only when the user is seated, unlike normal mode where they are kept warm for instant enjoyment.
• AUTOMATIC OPEN/CLOSE SEAT: Equipped with a sensor to automatically open/close the seat when the user is nearby or leaving. This function can be turned ON/OFF by long-pressing the RIGHT ARROW key on the remote. When AUTOMATIC OPEN/CLOSE SEAT is ON, the ECO MODE icon on the Light Indicator Panel blinks continuously.
• AUTOMATIC DRYING: Automatically starts drying the user after SPRAY or BIDET function for a complete cleaning session. This function can be turned ON/OFF by long-pressing the AIR DRYING key on the side control panel.
• AUTOMATIC FLUSHING: Flushes automatically after each use for optimal hygiene. This function can be turned ON/OFF by long-pressing the FLUSHING key on the remote.
• AUTOMATIC ODOR CATALYST: A fan sucks air from the bowl through an odor-fighting catalyst, preventing unpleasant smells during use for a pleasant experience.

CLEANING THE FILTER

1. Close the water shut-off valve by turning clockwise. Do not remove the filter before closing the valve.
2. Access the filter behind the toilet ceramic base. If the filter is hard to reach due to space constraints, uninstall the seat from the ceramic base (refer to installation instructions steps 4-7).
3. Unscrew the filter cover counterclockwise and remove the filter.
4. Clean the filter using a toothbrush for dirt on the filter and a cloth for dirt and deposits in the filter body. Use water only, not detergent. Do not apply excessive force or damage the filter's shape.
5. Re-install the filter and tighten it securely to prevent leaks.
6. Open the water shut-off valve counterclockwise. Ensure there are no leaks. If necessary, re-install the entire seat onto the ceramic base.

LONG TERM STORAGE

To prevent damage from frozen toilet water, drain any remaining water using the following method. When leaving for an extended period, ensure all water is drained from the toilet.

Press the DRYING and BIDET keys simultaneously for 3 seconds. The toilet will take 2 minutes to drain its water content and power off automatically, preparing it for storage. All toilet lights will blink every 3 seconds, accompanied by a long beep until the draining process is complete.

NOZZLE MAINTENANCE

To ensure proper washing function, clean the nozzle regularly:

1. Turn on the toilet.
2. Long-press the SPRAY key to turn off the toilet's sensors.
3. Press the SPRAY key again for 5 seconds to extend the nozzle.
4. Gently wash the nozzle with a soft, wet cloth or brush.
5. Press the POWER key to retract the nozzle and return the toilet to its normal state.

SPECIFICATION SHEET

MAINTENANCE & CONSUMER RESPONSIBILITIES

• The Distributor prohibits the use of harsh abrasive cleansers, as they can damage the inner workings of the toilets.
• For daily maintenance, use a wet cloth and a soft liquid cleaner.
• Never use abrasives or cleaners containing acetone, chlorine, strong bleach, scrapers, metallic brushes, or other objects that can scratch or tarnish surfaces.

LIMITED 1 YEAR WARRANTY

The Distributor's warranty is valid for 1 year from the purchase date. Improper use or deviations from the manual's guidance will void the warranty. This non-transferable warranty applies only to the original purchaser, and proof of purchase is required for all claims.

This warranty applies to Distributor toilets installed for residential use only. The Distributor warrants that, when installed according to recognized plumbing industry practices, the toilets will be free of manufacturing defects for one year from the purchase date.

The Distributor will repair or replace damaged products or parts only if they were installed and used according to this user manual. Before repair or replacement, the Distributor may send a representative to inspect the product. Service for inspection, repair, and replacement within the warranty period is free of charge; however, freight charges are the customer's responsibility.

INFORMATION ABOUT YOUR WARRANTY COVERAGE

This warranty does not cover damages or failures attributable to:

• Toilets installed with obvious visual defects.
• Rough handling or improper operation.
• Presence of sediment or impurity in the water supply system.
• Defects or damages caused by installation not strictly complying with the instructions in the Recognized Plumbing Industry Practice.
• Defects or damage caused by severe accidents (e.g., fire, electric surge).
• Damage caused by flooding or standing water from leaks, appliances, etc., including flooding and damage caused by acts of God.

NOTES ON WARRANTY

This warranty applies only to the original purchaser and installation site and is not transferable.

FOR WARRANTY SERVICE

To make a claim, contact the Distributor no later than 30 days after discovering a defect. Proof of purchase (e.g., bill of sale) is mandatory. The Distributor reserves the right to designate a representative for inspection. No unauthorized person is entitled to assume liability or alter warranty obligations.

INSTALLATION PICTURE

This section contains visual references for installation, showing water supply connections and the rear of the toilet.

CONTACT US

Head Office / Siège Social / Oficina Principal:
2800 Etienne Lenoir, Laval, Quebec H7R 0A3 Canada

Customer Service / Service à la clientèle / Service al cliente:
Tel: 1-866-839-2888
Fax: 1-866-922-9990
Email: customerservice@ovedecors.com

Hours: 8:00 am - 5:00 pm EST Monday - Friday (8h à 17h HNE, du lundi au vendredi; 8 h a 17 h HDE, de lunes a viernes)

English and French-speaking representatives are available.

Keep This Information:

• Purchase date: __________
• Product Tracking Reference: __________

Website: www.ovedecors.com