VEVOR

ELECTRIC MEAT GRINDER USER MANUAL

MODEL: SXC-12 SXC-22

VEVOR is committed to providing tools at competitive prices. Expressions like "Save Half" or "Half Price" represent an estimate of savings compared to major top brands and may not cover all product categories. Please verify savings when placing an order.

SXC-12 SXC-22

Picture for reference only.

NEED HELP? CONTACT US!

For product questions or technical support, please contact: CustomerService@vevor.com

This is the original instruction manual. Please read all instructions carefully before operating. VEVOR reserves the right to interpret its user manual. The product appearance is subject to the received product. VEVOR will not provide further notice for technology or software updates.

Warnings

When using electrical appliances, basic safety precautions should always be followed:

SAVE THIS INSTRUCTION!

1. READ ALL OPERATING INSTRUCTIONS AND PRODUCT SAFETY LABELS! Failure to follow instructions may result in serious injury or property damage!
2. CHECK FOR DAMAGED PARTS: Before use, ensure all parts function normally and perform expected functions. Check for alignment, binding, and installation of moving parts. If any parts, the Power Cord, or the Grinder are damaged, call Customer Service.
3. Always unplug the power cord when not in use, before attaching/removing parts, and before cleaning. After unplugging, turn the power switch ON then OFF to ensure all power is discharged.
4. This appliance can be used by children aged 8 and above, and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge, if supervised or instructed on safe use and understanding the hazards. Children shall not play with the appliance. Cleaning and maintenance should not be done by children without supervision.
5. NEVER LEAVE GRINDER UNATTENDED WHILE IT IS RUNNING!
6. ALWAYS USE THE PROVIDED STOMPER. NEVER FEED FOOD BY HAND. KEEP FINGERS CLEAR OF THE AUGER AND CUTTING BLADES AT ALL TIMES. NEVER REACH INTO THE GRINDER, as this may cause serious injury.
7. Always keep the tray guard in place while operating.
8. AVOID contact with moving parts. NEVER USE FINGERS TO SCRAPE FOOD AWAY FROM THE CUTTING BLADE WHILE IT IS IN OPERATION. SEVERE INJURY MAY RESULT.
9. Wait until all moving parts have stopped and turn off power before removing any part or switching the grinder in reverse.
10. TIE BACK loose hair, clothing, or any loose object and roll up long sleeves before operating.
11. REMOVE ties, rings, watches, bracelets, or other jewelry before operating.
12. DO NOT operate the Grinder with a damaged cord or plug, or after the unit malfunctions. DO NOT ATTEMPT TO REPLACE THE CORD. Call Customer Service for examination, repair, or adjustment.
13. DO NOT use outdoors; this product is intended for INDOOR USE ONLY.
14. DO NOT let the rope hang over the edge of a table or counter. Do not touch sharp edges or hot surfaces.
15. DO NOT allow the rope to kink, get stuck under the unit, or wrap around the grinder.
16. DO NOT pull the power cord to disconnect.
17. DO NOT USE WITH EXTENSION CORD. Always plug directly into a grounded wall receptacle.
18. Place the grinder on a firm and stable surface. Ensure it is not near the edge of the worktop where it can be easily pushed off or fall.
19. The Gear Housing and Motor Cover may become HOT during operation. This is normal. DO NOT TOUCH these parts while operating.
20. DO NOT attempt to operate the Grinder if the Grinder, Motor, and Gear Box are cold. The temperature should be at least 45°F (7°C) before starting operation.
21. To reduce the risk of unintentional starting, check that the control is OFF before plugging the cord into the wall outlet. To disconnect, turn the controller to OFF, then remove the plug from the wall outlet.
22. DO NOT operate your grinder under a wall cabinet. Always unplug the unit when storing. Failure to do so could create a fire risk.
23. NEVER plug the grinder in where water may flood the area.
24. To protect against electrical shock, DO NOT submerge the grinder in water or other liquids. Ensure the grinder is disconnected from the power source before cleaning. NEVER rinse the Grinder Motor under running water; use only a moist cloth.
25. The use of attachments or parts not recommended or sold by the manufacturer will void the warranty and may cause fire, electric shock, or injury.
26. HAND WASH ALL PARTS! DO NOT USE DISHWASHER. Never place the unit near a hot burner, in an oven, or in a dishwasher.
27. NEVER use abrasive cleaning agents or cloths when cleaning the grinder.
28. DO NOT use the grinder for other than its intended use.
29. DO NOT RUN Grinder without meat in the Grinder Head. Severe damage to the Head and Auger may occur.
30. NEVER open the meat grinder and run it dry for more than 10 seconds without meat inside. Friction will cause high heat and meat sticking. Do not dry run; damage from dry operation voids the warranty.
31. DO NOT attempt to grind bones, nuts, or other hard items.
32. WEAR EYE PROTECTION. Wear safety glasses conforming to ANSI Z87.1 requirements.
33. The Manufacturer disclaims responsibility for improper use. Improper use voids the warranty.
34. DO NOT use Grinder while under the influence of drugs or alcohol.
35. DO NOT REMOVE WARNING LABELS. Doing so voids the product warranty and may result in serious personal injury.
36. This appliance must be grounded. It uses a grounded, three-prong plug for connection to a grounded 120V (US)/230V (EC) wall outlet. DO NOT alter the plug. NEVER break off a grounding prong. Doing so voids the warranty and may result in electric shock.
37. Type Y attachment: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.

TECHNICAL PARAMETER

PARTS LIST

ASSEMBLY INSTRUCTIONS

IMPORTANT: BEFORE ASSEMBLING, MAKE SURE THE GRINDER IS NOT PLUGGED IN.

1. Loosen the Black Grinder Head Locking Knob. Insert the Grinder Head into the Motor Housing with the Feed Chute facing straight up. Turn clockwise until the slot on the top of the Grinder Head aligns with the Pin inside the Motor Housing. Tighten the Grinder Head Locking Knob.
2. Insert the Auger by aligning its Spline with the Drive Shaft. Turn the auger clockwise until it seats into the gear housing.
3. Place the Cutting Knife on the square portion of the Auger Pin. Ensure the flat side of the blade faces outward (one-way fit).
4. Place the Grinder Plate onto the Auger Pin, aligning the slotted notch with the bottom notch in the Grinder Head opening. The cutting plate will protrude approx. 1/8" out of the grinder head. RECOMMENDED: Use the coarse (10mm) plate for the first grind.
5. Attach the Front Head Ring Nut and turn it clockwise until snug against the Grinder Plate.
6. Place the neck of the Meat Tray into the Grinder Feed Chute Opening and press down until secure.

SAUSAGE STUFFING INSTRUCTIONS

WARNING! Before cleaning, assembling, or disassembling, ensure the PLUG IS REMOVED FROM THE OUTLET POWER SOURCE! Always unplug the Grinder when not in use. After unplugging, turn the power switch ON, then OFF to ensure all power is discharged.

IMPORTANT: While one person can operate this grinder for sausages, two people are recommended. One operates the grinder and feeds meat, while the other manages the sausage casings.

WARNING! NEVER RUN GRINDER DRY WITHOUT MEAT! It can damage the unit. Meat acts as a lubricant. If you run out of meat, turn the grinder off immediately.

TO BEGIN STUFFING:

1. Place seasoned ground meat into the Meat Tray. Do not overfill; leave the Feed Chute area open. (See Figure 1: Meat in tray)
2. Slide a sausage casing over the Stuffing Funnel. (See Figure 2: Casing on funnel)
3. Pull 4-6" (10-15 cm) of casing from the end of the Stuffing Funnel Tube and tie a knot in the end. (See Figure 3: Knotted casing)
4. Ensure the Grinder is OFF. Attach to power supply.
5. Press the Grinder "ON" button. Carefully feed ground meat into the Feed Chute. ONLY USE THE STOMPER TO PUSH MEAT; DO NOT USE FINGERS OR OTHER OBJECTS.
6. Hold the casing in place with one hand while feeding the sausage mixture. As meat fills the casing, gently lay it on a clean, dry surface. (See Figure 4: Sausage being formed)
7. Do not fill the last 4-6 inches (10-15.24 cm) of casings. After filling, twist the open end and tie tightly. Twist into a chain if desired.
8. Fill the casing slowly to avoid air pockets. If air pockets appear, prick them with a pin; the small holes will seal naturally.

CLEANING, MAINTENANCE & STORAGE

CLEANING INSTRUCTIONS

IMPORTANT: BEFORE CLEANING, ENSURE THE POWER IS TURNED OFF AND THE UNIT IS UNPLUGGED. Disassemble the Grinder Head and wash parts that contact meat in hot soapy water, removing all grease and oil. Rinse and dry all parts thoroughly before reassembling.

1. Wash all parts that have contacted meat in hot soapy water. CLEAN IMMEDIATELY AFTER USE. DO NOT IMMERSE THE MOTOR IN WATER OR OTHER LIQUIDS!
2. Rinse Grinder parts with clear hot water, and then dry them IMMEDIATELY.
3. Fully lubricate the Head, Auger, Plates, and Knife with a food-grade silicone spray before and after each use.
4. Clean the Motor Cover and Gear Housing with a damp towel and wipe dry. DO NOT IMMERSE THE MOTOR IN WATER OR OTHER LIQUIDS!

IMPORTANT: Metal parts must be coated with food-safe silicone spray to prevent rusting. Unprotected parts will rust quickly.

ENVIRONMENTAL PROTECTION

This product is subject to European Directive 2012/19/EC. The symbol of a crossed-out wheelie bin indicates separate refuse collection is required in the European Union. This applies to the product and all accessories marked with this symbol. Products marked with this symbol must not be discarded with normal household waste but taken to an electrical and electronic equipment collection point for recycling.

Importer: WAITCHX, Address: 250 bis boulevard Saint-Germain 75007 Paris

Importer: FREE MOOD LTD, Address: 2 Holywell Lane, London, England, EC2A 3ET

UK REP: EUREP UK LTD, UNIT 2264, 100 OCK STREET, ABINGDON, OXFORDSHIRE ENGLAND OX14 5DH

EC REP: EUREP GmbH, Unterlettenweg 1a, 85051 Ingolstadt, Germany

Manufacturer: Anhui Xuzhong Intelligent Technology Co., Ltd., Address: No.23, Lantian Road, Economic Development Zone, Wangjiang County, Anqing City, Anhui Province, China

MADE IN CHINA

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical Support and E-Warranty Certificate: https://www.vevor.com/support