Mitsubishi Electric Air Conditioning Control System - Optional Parts
Mounting Kit (for control panel)
Installation Manual
Applicable Models: AE-200A/AE-50A, AE-200E/AE-50E
For distribution to dealers and contractors only
PAC-YG86TK-J
Before installing the controller, please read this Installation Manual carefully to ensure proper operation. Retain this manual for future reference.
Contents
- Safety precautions
- 1. Parts to be used
- 1-1. Package contents
- 1-2. Commercially available parts
- 1-3. External dimensions
- 2. General description of installation
- 3. Selecting the installation site
- 3-1. Required installation space
- 4. Installation
- 4-1. Before installation
- 4-2. Installation method
- 5. Wiring connections
Safety precautions
Thoroughly read the following safety precautions prior to installation. Observe these precautions carefully to ensure safety.
After reading this manual, pass the manual on to the end user to retain for future reference. The user should keep this manual for future reference and refer to it as necessary. This manual should be made available to those who repair or relocate the units. Make sure that the manual is passed on to any future air conditioning system user.
All electrical work must be performed by qualified personnel.
WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
General precautions
CAUTION
To reduce the risk of injury, electric shock, or malfunction, avoid contact with the sharp edges of certain parts.
To reduce the risk of injury, wear protective gear when working on the controller.
Precautions for unit installation
WARNING
Properly dispose of the packing materials. Plastic bags pose a suffocation hazard to children.
Take appropriate safety measures against earthquakes to prevent the controller from causing injury.
To prevent injury, install the controller on a flat surface strong enough to support its weight.
Precautions for relocating or repairing the unit
WARNING
The controller must be repaired or moved only by qualified personnel. Do not disassemble or modify the controller. Improper installation or repair may result in injury, electric shock, or fire.
1. Parts to be used
1-1. Package contents
| No. | Package contents | Shape | Qty. | Notes |
|---|---|---|---|---|
| 1 | Mounting Kit | [Mounting Kit Diagram] | 1 | |
| 2 | DIN rail attachment | [DIN rail attachment Diagram] | 2 | |
| 3 | Screw | [Screw Diagram] | 4 | Use to fix the DIN rail attachments. |
| 4 | Installation Manual (this manual) | — | 1 |
1-2. Commercially available parts
| No. | Parts | Shape | Qty. | Notes |
|---|---|---|---|---|
| 1 | Ø4 screw | — | 4 | Required for wall-surface installation. Use screws that are suitable for the wall type. |
| 2 | DIN rail | [DIN rail Diagram] | As appropriate | Required when using DIN rails. |
| 3 | DIN rail fixing screw | — | As appropriate *1 | Use screws that are suitable for the wall type. |
| 4 | Control box | — | As appropriate | 200 mm (7-7/8 in) depth or above |
*1 The total weight of the AE-200A/AE-50A/AE-200E/AE-50E and the Mounting Kit is approximately 2.7 kg. Use the appropriate amount of fixing screws to secure the strength.
1-3. External dimensions
[1] Mounting Kit
[Diagram showing external dimensions of the Mounting Kit with measurements in mm and inches. Key dimensions include overall length, width, height, and hole placements for mounting.]
2. General description of installation
[Diagram illustrating the general installation of the AE-200/AE-50 body with the Mounting Kit and DIN rail attachment. Shows the connection points and components involved.]
Plate A fixing screw (supplied with AE-200/AE-50)
DIN rail attachment (supplied)
Screw (supplied)
Mounting Kit (supplied)
* Hereafter, AE-200A and AE-200E, unless otherwise specified, will be called "AE-200." Hereafter, AE-50A and AE-50E, unless otherwise specified, will be called "AE-50."
3. Selecting the installation site
3-1. Required installation space
[1] Required space around the AE-200/AE-50
[Diagram showing the required space around the AE-200/AE-50 unit for installation, including dimensions for clearance. Shows the Mounting Kit attached to the AE-200/AE-50 body within the installation space.]
Unit: mm (in)
[2] Required vertical shift distance
When the depth of the control box is below 200 mm (7-7/8 in), shift the controllers vertically as shown in the figure below so that their components will not be in contact with each other.
[Diagram illustrating the vertical shift distance for control boxes with depths less than 200 mm, showing how to arrange them to prevent contact.]
Unit: mm (in)
4. Installation
4-1. Before installation
- Remove the cover. Refer to the Installation Manual of the AE-200/AE-50 for how to remove the cover.
- Attach the Mounting Kit. [Diagram showing the AE-200/AE-50 body with the cover removed, and the Mounting Kit being attached using Plate A fixing screws.]
- Reinstall the cover.
4-2. Installation method
[1] Installation using DIN rail
- Attach the supplied two DIN rail attachments to the Mounting Kit with the supplied screws. [Diagram showing the AE-200/AE-50 body with the Mounting Kit attached, and the DIN rail attachments being secured to the Mounting Kit with screws.]
- Install the DIN rail on a strong wall surface. [Diagram showing a DIN rail being mounted to a wall using DIN rail fixing screws. Includes a note about not screwing in a specific location.]
Mounting location [Diagram showing the mounting location for the DIN rail with dimensions.]
Unit: mm (in)
3. Mounting the AE-200/AE-50 on the DIN rail [Diagram sequence showing how to mount the AE-200/AE-50 onto the DIN rail and how to remove it.]
[2] Wall-surface installation
- Install the AE-200/AE-50 on a strong wall with Ø4 screws. [Diagram showing the AE-200/AE-50 body being mounted directly to a wall using Ø4 screws, with the Mounting Kit attached.]
To remove the AE-200/AE-50 after the installation, remove the Plate A fixing screws that fix the AE-200/AE-50 and the Mounting Kit.
Mounting location [Diagram showing the mounting location for wall-surface installation with dimensions.]
Unit: mm (in)
5. Wiring connections
When routing the cables from the bottom, remove the service cover, cut out the knockout holes, cut a slit in the supplied rubber bushings (supplied with the AE-200/AE-50), attach the bushings to the knockout holes, insert the cables with no gap, and reinstall the service cover.
[Diagram showing the service cover of the AE-200/AE-50 unit, indicating where to route cables.]
