Installation Manual-MEAN WELL Switching Power Supply ManufacturerProduct Liability Disclaimer-MEAN WELL Switching Power Supply ManufacturerGlobal Trade Item Number (GTIN)-MEAN WELL Switching Power Supply Manufacturer
Instruction Manual for MEAN WELL models including: HBG-200 Serie s 200W Constant Voltage Constant Current LED Driver, HBG-200 Serie s, 200W Constant Voltage Constant Current LED Driver, Constant Current LED Driver, Current LED Driver, LED Driver
%product-title% - Conrad Electronic Suisse
Mean Well HBG-200-60 LED driver Constant voltage, Constant current 198 W 3.3 A 60 V DC not dimmable, PFC circuit, Surge Mean Well HBG-200-60 4021087049757
Mean Well HBG-200-36B LED driver Constant voltage, Constant current 198 W 5.5 A 36 V DC dimmable, 3-in-1 dimmer, PFC ci Mean Well HBG-200-36B 4021087049795
File Info : application/pdf, 9 Pages, 2.60MB
DocumentDocument200W Constant Voltage + Constant Current LED Driver
HBG-200 series
User's Manual
(for DA type only)
IP65 IP67
DALI
A
File Name:HBG-200-SPEC 2022-03-16
H B G - 2 0 0 200W Constant Voltage + Constant Current LED Driver
series
SPECIFICATION
MODEL OUTPUT
HBG-200-36
HBG-200-48
DC VOLTAGE
36V
48V
CONSTANT CURRENT REGION Note.2 21.6 ~ 36V
28.8 ~ 48V
RATED CURRENT
5.5A
4.1A
RATED POWER
198W
196.8W
RIPPLE & NOISE (max.) Note.3 250mVp-p
250mVp-p
CURRENT ADJ. RANGE
Adjustable for A-Type and AB-Type (via built-in potentiometer)
3.3 ~ 5.5A
2.46 ~ 4.1A
VOLTAGE TOLERANCE Note.4 ±2.0%
LINE REGULATION
±0.5%
LOAD REGULATION
±1.0%
SETUP, RISE TIME Note.6 2500ms,200ms /115VAC
500ms,200ms /230VAC
HOLD UP TIME (Typ.)
12ms /115VAC, 230VAC
VOLTAGE RANGE
90 ~ 305VAC 127~417VDC Note.5 (Please refer to "STATIC CHARACTERISTIC" section)
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR
PF>0.98/115VAC, PF>0.95/230VAC, PF>0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
HBG-200-60 60V 36 ~ 60V 3.3A 198W 350mVp-p
1.98 ~ 3.3A
INPUT
TOTAL HARMONIC DISTORTION
THD< 20%(@load60%/115VC,230VAC; @load75%/277VAC) (Please refer to "TOTAL HARMONIC DISTORTION(THD)" section)
EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER
92%
93%
1.9A / 115VAC 1A / 230VAC 0.9A / 277VAC
COLD START 85A(twidth=600s measured at 50% Ipeak) at 230VAC; Per NEMA 410
4 units (circuit breaker of type B) / 7 units (circuit breaker of type C) at 230VAC
93.5%
LEAKAGE CURRENT
NO LOAD / STANDBY POWER CONSUMPTION
<0.75mA / 277VAC Standby power consumption <0.5W for B/AB/DA-Type Blank/A-Type please refer to Note.8
OVER CURRENT
95~108% Constant current limiting, recovers automatically after fault condition is removed
PROTECTION SHORT CIRCUIT OVER VOLTAGE
Hiccup mode or constant current limiting, recovers automatically after fault condition is removed
41 ~ 47V
54 ~ 62V
65 ~ 75V
Shut down o/p voltage with auto-recovery or re-power on to recovery
OVER TEMPERATURE
WORKING TEMP.
MAX. CASE TEMP.
ENVIRONMENT
WORKING HUMIDITY STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
Shut down o/p voltage, recovers automatically after temperature goes down Tcase=-40 ~ +85 (Please refer to " OUTPUT LOAD vs TEMPERATURE" section) Tcase=+85 20 ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH ±0.03%/ (0 ~ 50) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY STANDARDS
UL8750(type"HL"),CSA C22.2 No.250.13-12,ENEC BS EN/EN61347-1,BS EN/EN61347-2-13 independent, BS EN/EN62384; GB19510.14, GB19510.1; EAC TP TC 004,IP65 or IP67 approved
SAFETY & EMC
OTHERS NOTE
DALI STANDARDS
Compliance to IEC62386-101, 102, 207 for DA type only
WITHSTAND VOLTAGE
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH
EMC EMISSION
Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@load60%) ; BS EN/EN61000-3-3; GB17625.1, GB17743,EAC TP TC 020
EMC IMMUNITY MTBF
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547,light industry level (surge immunity:Line-Earth:4KV,Line-Line:2KV),EAC TP TC 020 2042.7K hrs min. Telcordia SR-332 (Bellcore) ;207.4K hrs min. MIL-HDBK-217F (25)
DIMENSION
Refer to mechanical specification
PACKING
1.53Kg; 8pcs/13.8Kg/1.61CUFT
Product Liability DisclaimerFor detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:HBG-200-SPEC 2022-03-16
H B G - 2 0 0 200W Constant Voltage + Constant Current LED Driver
series
BLOCK DIAGRAM
EMI FILTER
I/P
&
RECTIFIERS
FG
PFC CIRCUIT
POWER SWITCHING
O.T.P.
O.L.P.
PWM & PFC CONTROL
RECTIFIERS &
FILTER
fosc : 100KHz
Vo+ VoO.C.P.
DETECTION CIRCUIT
O.V.P.
DRIVING METHODS OF LED MODULE
This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs.
100
Vo(%)
60 (min.)
(A) Constant
Voltage area
(B) Constant Current area
(C) Hiccup Protection
50
100
Io(%)
Typical output current normalized by rated current (%)
In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL.
File Name:HBG-200-SPEC 2022-03-16
H B G - 2 0 0 200W Constant Voltage + Constant Current LED Driver
series
DIMMING OPERATION
* DIM+ for B/AB-Type DA+ for DA-Type
* *DIM- for B/AB-Type DA- for DA-Type
*DIM+(Purple) **DIM-(Pink)
SVT 18AWG*2C
AC/L(Brown) AC/N(Blue) FG (Green/Yellow)
SJTW 18AWG*3C
SJTW 18AWG*2C
Vo+(Red) Vo-(Black)
3 in 1 dimming function (for B/AB-Type)
Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-:
0 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.)
Applying additive 0 ~ 10VDC
Vo+ +
+
Vo-
-
-
DIM+ +
Additive Voltage DIM-
"DO NOT connect "DIM- to -V"
Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
Vo+ +
+
Vo-
-
DIM+
Additive PWM signal DIM-
"DO NOT connect "DIM- to -V"
Output current (%)
Output current (%)
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
0% 0V 1V
2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage
100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0%
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input
File Name:HBG-200-SPEC 2022-03-16
H B G - 2 0 0 200W Constant Voltage + Constant Current LED Driver
series
Applying additive resistance:
Vo+ +
+
Vo-
-
DIM+
Additive Resistance DIM-
"DO NOT connect "DIM- to -V"
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0%
Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity forsynchronizeddimmingoperation) Dimming input: Additive resistance
Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%. 2. The output current could drop down to 0% when dimming input is about 0k or 0Vdc, or 10V PWM signal with 0% duty cycle.
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options.
N FG L
Relay
Switch
Adjuster
10K/N~100K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal
Green/ Yellow
Brown
Blue
AC/L AC/N
HBG-200 B-Type
DIM+ DIM-
V(-) V(+)
Purple Pink
Black Red
LED Lighting Fixture
Using a switch and relay can turn ON/OFF the lighting fixture.
DALI Interface (primary side; for DA-Type) Apply DALI signal between DA+ and DA-. DALI protocol comprises 16 groups and 64 addresses. First step is fixed at 8% of output.
File Name:HBG-200-SPEC 2022-03-16
H B G - 2 0 0 200W Constant Voltage + Constant Current LED Driver
series
OUTPUT LOAD vs TEMPERATURE(Note.11)
LOAD (%)
PF
LOAD (%)
100
100
80 230VAC
80
Input only
60
60
50
40
40
20
20
-40 -30
-10 0
15
30
50
60
70 (HORIZONTAL)
AMBIENT TEMPERATURE ()
-40 -20 0
10
30
50
70
Tcase ()
85
90 (HORIZONTAL)
LOAD (%)
STATIC CHARACTERISTIC
100 90 80 70 60 50 40
90 100 115 130 145 160 180 200 230 260 290 305
INPUT VOLTAGE (V) 60Hz De-rating is needed under low input voltage.
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 75
1
0.98
0.96
0.94
0.92
0.9
0.88 277V
0.86
0.84
230V
0.82
115V
0.8
0.78
50%
60%
70%
80%
90%
100%
(200W)
LOAD
TOTAL HARMONIC DISTORTION (THD)
48V Model, Tcase at 75
25%
20%
15%
277VAC
230VAC
10%
115VAC
5%
0%
50%
60%
70%
80%
90%
100%
LOAD
EFFICIENCY(%)
EFFICIENCY vs LOAD
HBG-200 series possess superior working efficiency that up to 93.5% can be reached in field applications. 48V Model, Tcase at 75
95
90
85 277V
80 230V
75 115V
70
65
60 10% 20% 30% 40% 50% 60% 70% 75% 80% 90% 100%
LOAD
File Name:HBG-200-SPEC 2022-03-16
THD
H B G - 2 0 0 200W Constant Voltage + Constant Current LED Driver
series
LIFETIME
LIFETIME(Kh)
120
100
80
60
40
20
0
20
30
40
50
60
70
80
90
Tcase( )
File Name:HBG-200-SPEC 2022-03-16
H B G - 2 0 0 200W Constant Voltage + Constant Current LED Driver
series
MECHANICAL SPECIFICATION
Blank-Type
132 151.68
66.5 52.5
8.2
Case No.211 Unit:mm
132 14.5
20 tc
M10*P1.5-18h
AC/L(Brown) AC/N(Blue) FG (Green/Yellow)
300±20 SJTW 18AWG*3C
4-6.0
tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point
15045° Ta
A-Type
132 151.68
66.5 52.5
8.2
200±20 SJTW 18AWG*2C
Vo+(Red) Vo-(Black)
132 14.5
13.33
20 tc
M10*P1.5-18h
AC/L(Brown) AC/N(Blue) FG (Green/Yellow)
300±20 SJTW 18AWG*3C
4-6.0
15045°
tc : Max. Case Temperature.(case temperature measured point) Ta Ta: Ambient Temperature measured point
200±20 SJTW 18AWG*2C
Vo+(Red) Vo-(Black)
13.00
132 14.5
B/DA-Type
132 151.68
20
tc
M10*P1.5-18h
* DIM+ for B-Type DA+ for DA-Type
* *DIM- for B-Type DA- for DA-Type
*DIM+(Purple) **DIM-(Pink)
300±20 SVT 18AWG*2C
AC/L(Brown) AC/N(Blue) FG (Green/Yellow)
300±20 SJTW 18AWG*3C
66.5 52.5
8.2
200±20 SJTW 18AWG*2C
Vo+(Red) Vo-(Black)
4-6.0
tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point
15045° Ta
File Name:HBG-200-SPEC 2022-03-16
132 14.5
13.33
H B G - 2 0 0 200W Constant Voltage + Constant Current LED Driver
series
AB-Type
132 151.68
66.5 52.5
8.2
20
tc
M10*P1.5-18h
DIM+(Purple) DIM-(Pink)
300±20 SVT 18AWG*2C
AC/L(Brown) AC/N(Blue) FG (Green/Yellow)
300±20 SJTW 18AWG*3C
4-6.0
15045°
Ta
tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point
INSTALLATIONS
200±20 SJTW 18AWG*2C
Vo+(Red) Vo-(Black)
13.00
Hanger
Chain
High Bay Light
Caution
Please inspect the appearance of the driver if the package is damaged. There should not be any cracks.
Please do not drop or bump the driver.
All screws including the suspension screw should be paired with a spring washer and locked tight.
The entire luminaire, including the driver, should be limited to 10Kg or less.
The luminaire should be cautiously protected from damage due to shock throughout packaging and transportation.
Please thoroughly follow the preceding cautionary notes to prevent the luminaire from falling, leading to injuries.
INSTALLATION MANUAL
Please refer to : http://www.meanwell.com/manual.html
File Name:HBG-200-SPEC 2022-03-16