Installation Guide for tp-link models including: EAP2115-Bridge UR KIT, EAP2115 Omada Wireless Bridge, EAP2115, Omada Wireless Bridge, Wireless Bridge, Bridge
BookmarksCopy Link
File Info : application/pdf, 2 Pages, 5.87MB
DocumentDocumentQuick Installation Guide Wireless Backbone Bridge Package Contents The kit contains a Main AP and a Client AP, which can be distinguished by the role switch on the AP. 2× 2× 4× Hardware Overview LEDs Role Switch RESET Button LAN Port Scan for Bridge AP Start Guide TERMS OF USE: The Omada Wireless Bridge series must be installed by a certified professional. Installers must abide by local rules and regulations in terms of legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements. Note: EAP2115-Bridge UR KIT is used as an example throughout the guide. Images may differ from your actual product. ©2025 TP-Link 7100001130 REV1.0.0 2× 2× 2× Guide 2× 2× 8× 1× Note: Accessories may vary by region and model. Installation 1 2 3 4 5 1 2 3 4 WARNING:To avoid damage, do not place the panels on a flat surface or push down on it. 6 2 1 1 2 3 7 8 9 Power On Option 1: Via PoE Switch Option 2: Via Passive PoE Adapter Ethernet cable (Length 100m) PoE Switch Note: For lightning & ESD protection, use the Shielded CAT5e (or above) cable with a ground wire. Ethernet cable (Length 100m) PoE LAN Auto Pairing The Main AP and Client AP in the same kit will automatically form a bridge network after powering on. Auto Pairing Scenario 1: Remote Camera Monitoring Auto Pairing Main AP Client AP Notes: 1. Check the role switch to ensure you have connected the Main AP and Client AP in the network correctly. You can toggle the role switch to change the AP's role if needed. 2. The default SSID on the product is only for device access and management. If you need an SSID to access the internet and service networks, refer to the Network Management section to set up the AP. 3. In a network without a DHCP Server, Bridge APs will use the following DHCP fallback IP addresses: Main AP: 192.168.0.254 Client AP: 192.168.0.253 NVR Main AP Scenario 2: Wi-Fi Extension Gateway/Router Main AP Auto Pairing Client AP Camera Client AP AP Clients Network Management Option 1: Standalone Mode Configure and manage APs through the Main AP. Auto Pairing Main AP Client AP Management Client Scan for Standalone Start Guide Option 2: Controller Mode Configure and manage APs (and other Omada devices) centrally with an Omada Controller. Omada App With the TP-Link Omada app, you can access and manage your Omada devices at a local site or remotely with a tap of your phone. Omada Central (Cloud-Based) Or Controller On-Premises Controller Gateway/Router Switch Main AP Main AP Scan for Controller Start Guide Main AP Client AP Client AP Client AP Scan for Omada App More Configurations For more configurations, refer to the User Guides of the Omada Controller and Omada APs at: https://support.omadanetworks.com/document/ Safety Information · Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid. · Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. · Do not use the device where wireless devices are not allowed. · Do not use any other chargers than those recommended. · The AP can be powered only by a passive PoE adapter or a PSE device (such as a PoE switch) that complies with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1. TP-Link hereby declares that the Bridge AP is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU, and (EU)2015/863. The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/. TP-Link hereby declares that the Bridge AP is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017. The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca/ Attention: In EU member states, EFTA countries and Northern Ireland, the operation in the frequency range 5150MHz - 5350MHz is only permitted indoors. Attention: In Great Britain, the operation in the frequency range 5150MHz - 5350MHz is only permitted indoors. For the EAP Controller, go to the Devices page and select the desired EAP to specify the channel. For the web browser, go to Wireless > Wireless Settings to specify the channel. AT BE BG CH CY CZ DE DK EE EL ES FI FR HR HU IE IS IT LI LT LU LV MT NL NO PL PT RO SE SI SK UK(NI) UK More Resources Main Site https://www.omadanetworks.com/ Video Center https://support.omadanetworks.com/video/ Documents https://support.omadanetworks.com/document/ Product Support https://support.omadanetworks.com/product/ Technical Support https://support.omadanetworks.com/contact-support/ Warranty For details on the warranty period, policy, and procedures, visit https://support.omadanetworks.com/warranty-services/. Support For technical support, user guides, and other information, please visit https://support.omadanetworks.com/, or simply scan the QR code.
Omada Network SupportCall Support | Omada Network SupportDocuments | Omada Network SupportProduct Support | Omada Network SupportVideo Center | Omada Network SupportWarranty Services | Omada Network Support
Omada - Networks Empower Business | TP-Link
CE Regulatory Compliance | TP-LinkRegulatory Compliance | TP-Link