p65warnings.ca.gov
Instructions for American Dryer models including: AD90-SS, AD90-SS Advantage AD Automatic Hand Dryer, Advantage AD Automatic Hand Dryer, Automatic Hand Dryer, Hand Dryer, Dryer
World Dryer AD90-SS Advantage AD Automatic Hand Dryer | Graybar Store
File Info : application/pdf, 2 Pages, 1.67MB
DocumentDocumenteXtremeAir SenSor replacement InStructIonS GXt6, GXt8, eXt2, and eXt4 SerIeS only WARNING: DISCONNECT POWER BEFORE INSTALLING DESUNA LA ELECTRICIDAD ANTES DE RACER REPARACIONES WARNING: CANCER AND REPRODUCTIVE HARM www.p65warnings.ca.gov CÁNCER Y DAÑO REPRODUCTIVO www.p65warnings.ca.gov Service of a hand dryer should be performed by a licensed electrician. 1. After disconnecting power, remove the cover by loosening the two tamper-resistant screws with the security wrench provided with the dryer. 2. Carefully unplug the four electrical connectors that plug into the sensor and disconnect the two lead wires from the power supply. Make a note of which wire goes to which terminal. 3. Carefully remove the nozzle assembly from the blower housing by removing the four screws. 4. Remove the sensor from the backplate by removing the single mounting screw. 5. Install the new sensor by attaching to the backplate with the mounting screw, position sensor as high as possible. Reconnect the four electrical connectors and the power supply, replace the nozzle assembly and cover. 6. After checking the wiring, apply power and test. INCREASE sensitivity (Figure 2) by using a flatblade screwdriver and CAREFULLY turning the adjustment pot located on the sensor CLOCKWISE 1/3 turn MAX. DECREASE sensitivity, turn COUNTERCLOCKWISE 1/3 Turn MAX. Figure 1 SenSor replacement SenSor nozzle ASS'y + - Figure 2 SenSitivity adjuStment American Dryer, Inc. · 340 County Line Road, Bensenville, IL 60106 U.S.A. PH (734) 421-2400 · www.americandryer.com · Revised June 2018 eXtremeAir SenSor replacement InStructIonS GXt6, GXt8, eXt2, and eXt4 SerIeS only WARNING: DISCONNECT POWER BEFORE INSTALLING DESUNA LA ELECTRICIDAD ANTES DE RACER REPARACIONES WARNING: CANCER AND REPRODUCTIVE HARM www.p65warnings.ca.gov CÁNCER Y DAÑO REPRODUCTIVO www.p65warnings.ca.gov Service of a hand dryer should be performed by a licensed electrician. 1. After disconnecting power, remove the cover by loosening the two tamper-resistant screws with the security wrench provided with the dryer. 2. Carefully unplug the four electrical connectors that plug into the sensor and disconnect the two lead wires from the power supply. Make a note of which wire goes to which terminal. 3. Carefully remove the nozzle assembly from the blower housing by removing the four screws. 4. Remove the sensor from the backplate by removing the single mounting screw. 5. Install the new sensor by attaching to the backplate with the mounting screw, position sensor as high as possible. Reconnect the four electrical connectors and the power supply, replace the nozzle assembly and cover. 6. After checking the wiring, apply power and test. INCREASE sensitivity (Figure 2) by using a flatblade screwdriver and CAREFULLY turning the adjustment pot located on the sensor CLOCKWISE 1/3 turn MAX. DECREASE sensitivity, turn COUNTERCLOCKWISE 1/3 Turn MAX. Figure 1 SenSor replacement SenSor nozzle ASS'y + - Figure 2 SenSitivity adjuStment American Dryer, Inc. · 340 County Line Road, Bensenville, IL 60106 U.S.A. PH (734) 421-2400 · www.americandryer.com · Revised June 2018 GX SerieS SenSor replacement inStructionS WARNING: DISCONNECT POWER BEFORE INSTALLING DESUNA LA ELECTRICIDAD ANTES DE RACER REPARACIONES WARNING: CANCER AND REPRODUCTIVE HARM www.p65warnings.ca.gov CÁNCER Y DAÑO REPRODUCTIVO www.p65warnings.ca.gov Service of a hand dryer should be performed by a licensed electrician. 1. After disconnecting power, remove the cover by loosening the two tamper-resistant screws with the security wrench provided with the dryer. 2. Carefully unplug the four electrical connectors that plug into the sensor and disconnect the two lead wires from the power supply. Make a note of which wire goes to which terminal. 3. Carefully remove the vent assembly from the blower housing by pulling. 4. Remove the sensor from the backplate by removing the single mounting screw. 5. Install the new sensor by attaching to the backplate with the mounting screw, reconnect the four electrical connectors and the power supply, replace the vent assembly and cover. 6. After checking the wiring apply power and test, INCREASE sensitivity (Figure 2) by using a flatblade screwdriver and CAREFULLY turning the adjustment pot located on the sensor CLOCKWISE 1/3 turn MAX. To DECREASE sensitivity, turn COUNTERCLOCKWISE 1/3 turn MAX. Figure 1 SenSor replacement GX SerieS replacement inStructionS WARNING: DISCONNECT POWER BEFORE INSTALLING DESUNA LA ELECTRICIDAD ANTES DE RACER REPARACIONES WARNING: CANCER AND REPRODUCTIVE HARM www.p65warnings.ca.gov CÁNCER Y DAÑO REPRODUCTIVO www.p65warnings.ca.gov Service of a hand dryer should be performed by a licensed electrician. 1. After disconnecting power, remove the cover by loosening the two tamper-resistant screws with the security wrench provided with the dryer. 2. Carefully unplug the four electrical connectors that plug into the sensor and disconnect the two lead wires from the power supply. Make a note of which wire goes to which terminal. 3. Carefully remove the vent assembly from the blower housing by pulling. 4. Remove the sensor from the backplate by removing the single mounting screw. 5. Install the new sensor by attaching to the backplate with the mounting screw, reconnect the four electrical connectors and the power supply, replace the vent assembly and cover. 6. After checking the wiring apply power and test, INCREASE sensitivity (Figure 2) by using a flatblade screwdriver and CAREFULLY turning the adjustment pot located on the sensor CLOCKWISE 1/3 turn MAX. To DECREASE sensitivity, turn COUNTERCLOCKWISE 1/3 turn MAX. Figure 1 SenSor replacement SenSor Vent ASS'y SenSor Vent ASS'y Figure 2 SenSitivity adjuStment American Dryer, Inc. · 340 County Line Road, Bensenville, IL 60106 U.S.A. PH (734) 421-2400 · www.americandryer.com · Revised June 2018 Figure 2 SenSitivity adjuStment American Dryer, Inc. · 340 County Line Road, Bensenville, IL 60106 U.S.A. PH (734) 421-2400 · www.americandryer.com · Revised June 2018