Instruction Manual for Portkeys models including: MT22DS 21 inch Dual Screen Monitor, MT22DS, 21 inch Dual Screen Monitor, Dual Screen Monitor, Monitor
MT22DS User Manual | Portkeys Official Site
File Info : application/pdf, 25 Pages, 4.09MB
DocumentDocumentProduct Manual
21.5" 1000NIT 3G-SDI&HDMI DUAL SCREEN PRODUCTION MONITOR
MT22DS
Product Information
523.6mm
21.5
1/4 Screw Hole Color Calibration
NPF H and V Power Supply System
Handle
NPF H and V Power Supply System
320.6mm F1 F2 F3 F4
F5 F6 F7 F8 PBP R90°
HDMI SDI 1 SDI 2
Overlay
Exit Menu
Power
MIRROR
Image
Knob
Switch
Capture Hyaline
Image
Image
65.8mm
XLR 2 48V
XLR 1 48V
DC 12~24V
8A
DC 12~24V
8A
GPI HDMI HDMI SDI SDI SDI OUT IN IN 1 IN 2 OUT 1
1/4 Screw Hole
Video Source Switch & Flip
1/4 Screw Hole
1/4 Screw Hole
Basic Parameters
Screen Size Dimension Viewing Angle Brightness Resolution Contrast Ratio Color Gamut Color Depth Weight Material Input Voltage Maximum Power Fan Menu Language Operating System
21.5 523.6×320.6×65.8mm 80 /80 /80 /70 1000nits 1920x1080 1000:1 Rec.709 8bit 5.8kg Aluminum Alloy DC 12~24V 60W Yes English / Simplified Chinese Portkeys OS
Packing List
MT22DS Monitor
Power Cable 12V8A
M2.5Inner Allen Key Folding Holder
Crystal Dropping Glue Button Micro USB Flash Drive
Serial Communication to 5-pin Aviation Connector
HDMI Input / Output Signal
1920×1080p@23.97Hz,24Hz,25Hz,29.97Hz,30Hz,50Hz,59.94Hz,60Hz 1920×1080psf@23.97Hz,24Hz,25Hz,29.97Hz,30Hz 1920×1080i@50Hz,59.94Hz,60Hz 1280×720p@50Hz,59.94Hz,60Hz 720×576p&720×576i@50Hz 720×480p&720×480i@50Hz,59.94Hz,60Hz
Interface
Video Input/Output Signal Conversion USB-A
Audio Input /Output Power Input /Output
Color Calibration Port Built-in Speaker
Input Interface 3G SDI X 2GPIHDMI Output Interface 3G SDIHDMI HDMI IN to SDI OUTSDI IN to HDMI OUT Waveform OUT3D LUT OUT Upgrade FirmwareLoad LUTFreeze-frame JPG Image LoadingThird-party JPG Image Loading JPG Instruction Manual Loading Input Interface XLR 1XLR 248V Phantom Output Interface 3.5mm Headphone Jack Input Interface 4 Pin XLR 12~24V Output InterfaceUSB 5VWireless Video Transmission Power Supply Plate Color Calibration 43W
Adaptable Battery Plate
V-mount Plate AB Mount Plate IDX Plate
Sony V-mount Anton Bauer Mount Sony V-mount / Anton Bauer Mount
SDI Input / Output Signal
1920×1080p@50fps,59.94fps,60fps 1920×1080p@50Hz,59.94Hz,60Hz YUV422 1920×1080p@23.98Hz,24Hz,25Hz,29.94Hz,30Hz YUV444/YUV422 1920×1080psf@23.98Hz,24Hz,25Hz,29.97Hz,30Hz YUV444/YUV422 1920×1080i@50Hz,59.94Hz,60Hz YUV444/YUV422 1280×720p@50Hz,59.94Hz,60Hz YUV444/YUV422
Catalogue
Operation Instruction
Operation Instruction
01
Button Introduction 01-02
Multi-Screen Operation 03-04
Menu Introduction
Main Menu Guides Image Config XLR Config System Config LUT Config Function Setup GPI Setup PBP / PIP Setup Firmware
05 05-06
06 07 07-08 09-10 11-19 19 20 20
Software Upgrade
Update(USB)
21
Operation Instruction
Brief: All operations of the MT22DS can only be accessed via external buttons.
Rotate Left
Press
Rotate Right
(Menu Knob)
Introduction to External Button Operations on the Monitor
Use the "Knob" to select functions and adjust parameters; Press the "Knob" to select parameters;
Scroll the "Knob" left or right to adjust parameters;
2 Rotate "Knob" left or right to adjust the volume
01
Button Introduction
(Buttons on the back)
(Front Buttons)
The above 8 buttons are custom function buttons. You can replace or adjust these functions in the "Software Settings" menu. (Refer to picture 1)
Function Setup
Function 1 Function 2 Function 3 Function 4 Function 5 Function 6 Function 7 Function 8 GPI Waveform Back
Peaking False Color Check Field
Guides Wa v e f o r m Audio Meters H2V Crop PBP(PIP)
RGB WF
Picture 1
When the MT22DS is connected to two or more signal sources, multiple signal source screens can be displayed simultaneously; (This function is invalid when there is only one signal source; when two or three signals are connected, press this button to enter the multi-screen interface.)
Rotate the image by 90°; When the "PBP" function is enabled, you can select an individual screen to rotate.
Mirror the image in four directions: left/right/up/down; When the "PBP" function is enabled, you can select an individual screen to mirror using the "Video Source Switch" button.
Switch the signal source of the image through the button; When the "PBP" function is enabled, you can use the "Video Source Switch" button to change the signal source for a selected screen.
02
When a U-disk is inserted, use this button to capture the current screen and save it to the U-disk.
When a U-disk is inserted, an image can be overlaid onto the current screen.The image can be obtained via "capture image" or manually added to the 'Capture' folder on the U-disk. Note: The images must be in 169 1920x1080 JPG format and cannot exceed 1MB, or the overlay will invalid. Press the button and then use the "Knob" to adjust the transparency of the image overlay.
Exit the menu or software function interface.
03
Multi-Screen Operation
Dual-screen
When two or three signals are connected, press the "PBP" button to enter the multi-screen interface. The "Signal Button" light will light up. (the monitor automatically recognizes the number of connected signals)
(PBP button)
(Dual-screen interface) The signal highlighted in blue indicates the current audio input.
(Triple-screen interface)
(Video Source Switch and Flip) When the screen interface is in dual-screen mode, use the "Video Source Switch and Flip" button to select the A/B image for 90° rotation, mirroring, and other functions.
(Signal button) When the screen interface is in triple-screen mode, you can turn off a signal by pressing any signal button (the signal button light will turn off, indicating the signal is off), entering dual-screen mode
Triple-screen
When three signals are connected, press the "PBP" button to enter the multi-screen interface. The "Signal Button" light will light up. (the monitor automatically recognizes the number of connected signals)
(PBP button)
04
In the triple-screen interface, press the "R 90°" button or the "Mirror" button, and the three screens will change synchronously.
(Triple screen - Rotate 90°)
(Triple-screen interface)
(Triple screen - Mirror)
05
Menu Introduction
Guides
Main Menu
Guides I ma g e C o nfi g XLR C o nfi g S ys te m C o nfi g LU T C o nfi g Function Setup GPI Setup PBP / PIP Setup Firmware Exit
Bring up the main menu
Main Menu
Press the exit button,
Use the "Knob" to bring up the main menu interface.
complete the adjustment
The main menu includes settings for:
"Guides", "Image Config", "XLR Config", "System Config", "LUT Config",
"Function Settings", "GPI Settings", "PBP", and "Firmware"
(Knob)
Guides
Guides H(Custom) V(Custom)
Guide Masks Cross Hair Grids GPI Guide 1 GPI Guide 2 GPI Grid Back
O ff --On O ff O ff 80% 90% 3
Guides:
Off / 80% / 90% / 11 / 169 / 916 / 159 / 43 / 1.51 / 1.851 / 21 / 2.351 / 2.391 / Custom
H(Custom):
1~100%Adjustable when the Guides is set to "Custom"
V(Custom:
1~100%Adjustable when the Guides is set to "Custom"
Guide Masks:
On / Off
Cross Hair:
On / Off
Grids:
Off / 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9
GPI Guide 1:
Off / 80% / 90% / 11 / 169 / 916 / 159 / 43 / 1.51 / 1.851 / 21 / 2.351 / 2.391 / Custom
GPI Guide 2:
Off / 80% / 90% / 11 / 169 / 916 / 159 / 43 / 1.51 / 1.851 / 21 / 2.351 / 2.391 / Custom
GPI Grid:
1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9
06
Image Config
Image Config
Brightness Contrast Chroma Sharpness Tint Color Temperat u re Backlight Anamorphic GPI Anamorphic Back
50 50 50 3 50 6500K 10 1X 1.33X
Brightness:
0~100
Contrast:
0~100
Chroma:
0~100
Sharpness:
0~10
Tint:
0~100
Color Temperature:
5600K / 6500K / 7500K / 9300K / Manual
Backlight:
1-10
Anamorphic:
1X / 1.33X / 1.42X / 1.5X / 1.6X / 1.66X / 1.85X / 2X / 2.35X / User
GPI Anamorphic:
1X / 1.33X / 1.42X / 1.5X / 1.6X / 1.66X / 1.85X / 2X / 2.35X / User
XLR Config
XLR Config
XLR Input
O ff
Back
XLR Input:
On / Off
07
System Config
System Config
OSD-Language OSD-Duration O S D -Tr a n s p a r a n c y Menu Setup Tou c h D i splay F B u t ton Detect Data Source System Reset Flip Control SDI Level A/B Out SDI 1080P->I Out
English O ff Low
User 1 On
After LUT
Auto O ff
System Config
SDI Load LUT Out
O ff
Back
OSD-Language:
Simplified Chinese / English
OSD-Duration
Off / 5 Sec / 10 Sec / 15 Sec / 20 Sec / 25 Sec / 30 Sec
OSD-Transparancy:
Off / Low / Medium / High
Menu Setup:
User 1 / User 2 / User 3 / User 4 / User 5
Touch Display F Button:
On / Off
Detect Data Source:
Before LUT / After LUT
System Reset:
According to the popup, LUT reset operations can be performed. (Refer to picture 2)
System Config
OSD-Language OSD-Duration O S D -Tr a n s p a r a n c y Menu Setup To u c h Disp lay F B utto n Detect Data Source System Reset Flip Control SDI Level A/B Out SDI 1080P->I Out
English O ff Low
User 1 On
After LUT
Auto O ff
Are you sure ?
Press to confirm
Yes
No
Picture 2
08
Flip Control:
Flip Control
Display Flip Mode
O ff
H Flip
On
V Flip
On
Osd Flip Mode
O ff
H Flip
On
V Flip
On
Back
Display Flip Mode:
On / Off
H Flip:
On / Off
V Flip:
On / Off
SDI Level A/B Out:
Auto / Level A / Level B
SDI 1080P->I:
On / Off
SDI Load LUT Out:
On / Off
Osd Flip Mode:
On / Off
H Flip:
On / Off
V Flip:
On / Off
LUT Config
LUT Config
3D LUT Stored from USB USB Search Reset LUT Display Gamut
No data Loa d use r c a lib ratio n fi l e Back
O ff Rec.709
3D LUT:
OnNull / Off
Stored from USB:
Stored from USB
XX XX XSto re d LU T C o nfigu ration XX XX XSto re d LU T C o nfigu ration XX XX XSto re d LU T C o nfigu ration XX XX XSto re d LU T C o nfigu ration Back
Select a file name, and press the "Knob" to load the LUT.
To delete the LUT file, long press the "Knob" exceeds three seconds, According to the popup, LUT file deletion operations can be performed. (Refer to picture 3)
09
(long press exceeds three seconds)
Stored from USB:
Delete Are you sure?
Yes
No
Picture 3
(USB Interface)
Save the LUT file (XXXXX.cube) to the root directory of the U-disk, then insert the U-disk containing the LUT file into the USB port of the MT22DS.
Use the "Knob" to find the "USB Search" interface in the "LUT Config".
10
Select the U-disk name option to enter the LUT file browsing interface. (Refer to picture 4)
Picture 4
Press the "Knob". When the selected box shows the " ", the LUT is loaded and saved to the "User Storage" interface.
Note: LUT files support repeated storage. If you want to delete them, please enter the user storage interface. LUT file format is .Cube, supporting 16/17/32/33/64/65 precision (LUT_3D_SIZE)
Reset LUT:
According to the popup, LUT reset operations can be performed . (Refer to picture 5)
LUT Config
3D LUT Stored from USB USB Search Reset LUT Display Gamut
No data Load u ser c ali brat i on file Back
O ff Rec.709
Press to confirm
Reset LUT Are you sure?
Yes
No
Picture 5
Display Gamut:
Bypass / Rec.709 / User 1 / User 2
LUT Config
3D LUT
No
Stored from USB
USB Search
Reset LUT
Display Gamut
User1
XXXXXXXXName of the loaded LUT
Loa d use r c a lib ratio n fi l e
Back
When the color gamut is set to "User 1" or "User 2," you can load LUT files in the "Load User Calibration File" option (the loading steps are the same as the "USB Search" function). The name of the loaded file will be displayed below the "Color Gamut" option.
11
Function Setup
Function Setup
Function 1 Function 2 Function 3 Function 4 Function 5 Function 6 Function 7 Function 8 GPI Waveform Back
Peaking False Color Check Field
Guides Wa v e f o r m Audio Meters H2V Crop PBP(PIP)
RGB WF
Software Function
*Peaking *False Color* *Zebra *Underscan *Waveform* *Rectangle Crop
*Audio Meters 3D LUT *Time Code H2V Crop PBP(PIP) Input SDI 1
Input SDI 2 Input HDMI Check Field* *Guides* *Cross Hair *Grids*
*Note: Set functions in the custom function keys (F1-F8). Long press the custom function key (F1-F8) for 3 seconds to bring up the parameters settings box.
GridsOn Long Press 3sec to set function.
Long press the custom function button for 3 seconds
Grids Setting
Grids
3
Color Exit
White
*Note: Continuously pressing the custom function button can adjust the corresponding function parameter.
Peaking Setting
Peaking Setting
Factor Color Style Grayscale Level Frame Masks Exit
Red Colour 100%
On
Peaking Setting Factor
Sensitivity
1
Peak Thresh
30
Brightness
0
Contrast
0
Thickness
10
Back
Sensitivity:
1-10
Peak Thresh:
0-100
Brightness:
-100 - +100
Contrast:
-100 - +100
Thickness:
1-10
12
Color:
Red / Green / Blue / White
Style:
Colour / Grayscale / Colour (Edge Enhance)
Grayscale Level:
0% / 50 / 100%
X S t art Y S t art Wide Height Reset Back
Peaking Setting Frame
0% 0% 100% 100%
X Start:
0%-99%
Y Start:
0%-99%
Wide:
1%-100%
Height:
1%-100%
Reset:
Press the "Knob" to reset the Peaking Frame
Masks:
On / Off
False Color Setting
False Color Setting
Underexposure
-1
Overexposure
101
IRE Indication
On
Exit
Underexposure("User mode" is adjustable):
-7 - 15
Overexposure("User mode" is adjustable):
85-110
IRE Indication:
On / Off
13
Zebra Setting
Zebra Area Option Enable IRE Range Color Exit
Zebra Setting
On High
On 100 -Red
Zebra:
On / Off
Area Option:
Low / Medium / High
Enable:
On / Off
IRE:
-7 - 109
RangeAdjustable when the "Area Option" is set to "Medium":
±0 - ±30
Color:
White / Red / Green / Blue
Underscan Setting
Factor Exit
Underscan Setting
94
Factor:
50-100
14
Waveform Setting
Waveform Setting
Wa v e f o r m
On
Options
Blending
--
Warning Color
O ff
Underexposure
0
Overexposure
100
Exit
Waveform:
Off / Full Screen / Four Screen / All Types / User Mode
Waveform Options - Full Screen
Full Screen Video Display Back
Luma WF On
Full Screen:
Luma WF / RGB WF / VectorScope / Luma HIS / RGB HIS
Video Display:
On / Off
Waveform Options - User Mode
Luma Waveform RGB Waveform Ve c t o r S c o p e Luma Histogram RGB Histogram Back
Luma Waveform
Luma Waveform
On
Position
L+ B
Back
Luma Waveform:
On / Off
Position:
L+T / M+T / R+T / L+C / R+C / L+B / M+B / R+B
15
RGB Waveform Position Back
RGB Waveform
On R+B
RGB Waveform:
On / Off
Position:
L+T / M+T / R+T / L+C / R+C / L+B / M+B / R+B
Ve c t o r S c o p e Position Back
VectorScope
On M+B
VectorScope:
On / Off
Position:
L+T / M+T / R+T / L+C / R+C / L+B / M+B / R+B
Luma Histogram
Luma Histogram
On
Position
R +T
Back
Luma Histogram:
On / Off
Position:
L+T / M+T / R+T / L+C / R+C / L+B / M+B / R+B
RGB Histogram Position Back
RGB Histogram
On R+C
RGB Histogram:
On / Off
Position:
L+T / M+T / R+T / L+C / R+C / L+B / M+B / R+B
16
Blending"Fullscreen" or "User Mode" adjustable:
Off / Low / Medium / High
Warning Color:
On / Off
Underexposure:
-7 - 50
Overexposure:
50-100
Rectangle Crop Setting
Rectangle Crop Setting
Rectangle Crop
ON
Resize
Exit
Rectangle Crop:
On / Off
X S ta rt Y S ta rt Wide Height Reset Back
Rectangle Crop Setting
25% 25% 50% 50%
X Start:
0%-99%
Y Start:
0%-99%
Wide:
1%-100%
Height:
1%-100%
Reset:
Press the "Knob" to reset Rectangle Crop
17
Audio Meters Setting
Audio Meters Audio Channel Position Exit
Audio Meters
On 8 Channel
To p
Audio Meters:
On / Off
Audio Channel:
2 Channel / 8 Channel
Position:
Top / Division / Bottom
Time Code Setting
Time Code Position Exit
Time Code Setting
On L+T
Time Code:
No / Off
Position:
L+T / M+T / R+T / L+C / R+C / L+B / M+B / R+B
18
Guides Setting
Guides HCustom VCustom
Color Thickness Guide Masks Exit
Guides Setting
80% --White 2 On
Guides :
Off / 80% / 90% / 11 / 169 / 916 / 159 / 43 / 1.51 / 1.851 / 21 / 2.351 / 2.391 / Custom
HCustom:
1~100%Adjustable when the Guides is set to "Custom"
VCustom:
1~100%Adjustable when the Guides is set to "Custom"
Color:
White / Red / Green/ Blue / Black
Thickness:
0-50
Guide Masks:
On / Off
Cross Hair Setting
Cross Hair Color X O ff s e t Y O ff s e t Exit
Cross Hair Setting
On White 50% 50%
Cross Hair:
On / Off
Color:
White / Red / Green/ Blue / Black
X Offset:
0%-100%
Y Offset:
0%-100%
19
Grids Setting
Grids Color Exit
Grids Setting
1 White
Grids:
Off / 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9
Color:
White / Red / Green/ Blue / Black
GPI Setup
GPI Setup
GPI Control GPI 1 GPI 2 GPI 3 GPI 4 GPI 5 GPI 6 GPI 7 Back
O ff Undefin ed Undefin ed Undefin ed Undefin ed Undefin ed Undefin ed Undefin ed
GPI Control:
On / Off
GPI 1 / 2 / 3 / 4 / 5 / 6 / 7:
Use the "Knob" to switch software functions.
Guide 1 Guide 2 Cross Hair Grid Input SDI 1
Input SDI 2 Input HDMI Anamorphic R [Tally] G [Tally]
Y [Tally] Underscan Red [CheckF] Green [CheckF] Blue [CheckF]
Mono [CheckF] 3D LUT Waveform False Color Peaking
Zebra Audio Meters Time Code Rectangle Crop Backlight
20
PBP/PIP Setup
PBP/PIP Setup
PBP/PIP Sound Source
A
PBP/PIP Swap
PIP Position
R +T
Back
PBP/PIP Sound Source:
A / B / C
PBP/PIP Swap:
In dual-screen mode, use the "knob" to switch the screens left and right.
PIP Position:
R+T / L+B / R+B / L+T
(GPI Interface)
Firmware
Firmware
Version Information Update(USB) Back
Version Information:
Check the firmware version according to the popup window.(Refer to picture 6)
Firmware Ver. MT22-V2.11.28.13
Press to confirm
Picture 6
21
Update(USB)
(USB Interface) Save the upgrade file (MT22DS.bin) to the root directory of the U-disk, then insert the U-disk into the USB port of the MT22DS. Use the "Knob" to find the "Software Upgrade (USB)" option in the "Firmware" section to upgrade the firmware. (Refer to picture 7)
Firmware
Version Information Update(USB) Back
Up da te ( U S B )
Are you sure?
Press to confirm
Yes
No
Picture 7
Adobe Illustrator 24.2 (Windows) Adobe PDF library 15.00