Global HR Solutions & Employment Tools for Distributed Teams | Remote
One moment, please...
User Manual for URC models including: UR3L-SR4, Subscription Broadcast Remote Control, UR3L-SR4 Subscription Broadcast Remote Control, Remote Control
Technical Support | URC Automation
File Info : application/pdf, 2 Pages, 465.82KB
DocumentDocumentOperating Manual For Easy Clicker UR3L-SR4 1 Introduction This remote control is designed to operate most IPTV and DTA STBs as well as Digital and Analog Cable Boxes. 2 Replacing Batteries Before you program or operate the remote control, you must install two new AAA alkaline batteries. STEP1 Remove the battery com- partment cover from the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover. 3 Button Functions Universal Remote Control, Inc. www.universalremote.com OCE-0082B REV 31 (02/25/22) 4 Programming the Remote Control *Note : Inthissection,whenyouareinstructedtopressa[DEVICE]button,thatmeansyoushouldpresseitherthe CBL,TV,orDVDbutton,dependingonwhichdeviceyouareprogrammingtheremotetooperate. A. Quick Set-Up Method STEP1 Turn on the component you want to program. To program your TV, turn on the TV. STEP2 Press and hold the [DEVICE] key for 5 seconds until the Device LED will blink once and stays on. Continue to hold the [DEVICE] key and press the number key assigned to your brand in the Quick Setup Code Table and release both [DEVICE] key and the number key to save the code. The Device LED will blink twice to confirm that the code is stored. STEP3 Point the remote control at the component. STEP4 Press the power button. If it turns off, it is programmed for your component. If it does not turn off, use the PreProgrammed 3-Digit code Method or Scanning Method. Repeat the steps above for all components. (CBL, TV, DVD). B. Quick Set-up Code Tables CBL QuickNumber Manufacturer/Brand 0 PACE DTA 1 SA/CISCO, SAMSUNG, PACE DIGITAL 2 MOTOROLA DIGITAL 3 MOTOROLA DTA 4 EVOLUTION DTA 5 CISCO IPTV 6 ADB IPTV 7 TECHNICOLOR 8 AMINO 140/540 IPTV 9 MOTOROLA IPTV TV QuickNumber Manufacturer/Brand 0 SANYO 1 SONY 2 SAMSUNG 3 LG 4 TOSHIBA 5 PANASONIC 6 PHILIPS 7 HITACHI 8 SHARP 9 VIZIO DVD QuickNumber Manufacturer/Brand 0 HITACHI 1 SONY 2 PHILIPS 3 SAMSUNG 4 PHILIPS MAGNAVOX 5 PANASONIC 6 LG 7 JVC 8 DENON 9 PIONEER C. Manual Programming The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of equipment. The threedigit code numbers are listed in the code tables sections of this instruction manual. STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD) . STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off. *Note: Youcanverifythatyouhave selectedthecorrectcodeby pressingthe[POWER]button. Theequipmentshouldturn backon.Thentryallofthe functionsontheremotecon- trol(i.e.volume,mute,etc.)to ensureyouhavethecorrect code.Ifanyofthefunctionsdo notoperateastheyshould, repeattheinstructionsfrom STEP3aboveusingthenext threedigitcodenumberfrom thebrandlist. STEP4 Store the three-digit code by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored. D. Auto Search Method If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps: STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD). STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on. STEP3 Press the [CH5] or [CH6] button one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release the [CH5] or [CH6] button as soon as the equipment turns off. *Note: Youcanverifythatyouhave selectedthecorrectcodeby pressingthe[POWER]button. Theequipmentshouldturn backon.Thentryallofthe functionsontheremotecontrol(i.e.volume,mute,etc.)to ensureyouhavethecorrect code.Ifanyofthefunctionsdo notoperateastheyshould, repeattheinstructionsfrom STEP3abovetocontinuethe AutoSearchMethod. STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored. E. To find the Three-Digit Code that Was Programmed using the Auto Search Method STEP1 Press the appropriate [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on. STEP2 Press the [INFO] button. The device LED will blink a number of times indicating the number of each digit for the code. Each digit is separated by a one second interval of the LED being off. Example : Oneblink,thenthreeblinks, theneightblinksindicates thecodenumber138. *Note : Tenblinksindicatesthenumber0. F. Programming a Second TV to the DVD Button STEP1 Press the [DVD] button and the [OK/SEL] button simultaneously for 3 seconds. The DVD LED will turn on for 30 seconds. The next step must be performed while the LED is on. STEP2 Press the [TV] button. STEP3 Point the remote control toward the TV and enter the three-digit code for your TV from the TV codes table. STEP4 Store the three-digit code by pressing the [DVD] button. The device LED will blink twice to confirm that the code has been stored. G. The Learning Method STEP1 Press the [Device] button (CBL, TV or DVD) to be programmed and the [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on. STEP2 Line up the UR3L-SR4 to the other remote, head-to-head, 1 or 2 inches apart. STEP3 Press any button on the UR3LSR4 that you want to teach a command to. For example, if you want to teach the [MUTE] button, press the [MUTE] button. STEP4 Press and hold the [MUTE] button on the other remote until the UR3L-SR4 Device LED light blinks twice. *Note : TheLEDwillblink5timesifthere wasanerrorinthelearning process.Inso,repeatSTEPS3and 4.Continuelearningotherbuttons byrepeatingSTEPS3and4. STEP5 Once you have completed teaching UR3L-SR4 all desired commands for that Device, save the learned commands by pressing the [Device] and [INPUT] buttons simultaneously until the Device LED blinks 3 times. Now test all the buttons to make sure they learned correctly. H. Erasing a Single Learned Command STEP1 Press the [Device] and [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on. STEP2 Press and hold the button you want to erase for 3 seconds. The Device LED will blink twice to confirm the erasure. STEP3 To exit, press and hold both the [Device] and [INPUT] buttons simultaneously until the Device LED blinks 3 times. I. Erasing All Learned Commands from One Device STEP1 Press the [DEVICE] and [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on. STEP2 Press and hold both the [DEVICE] button you want to erase and the [PAUSE] button for 5 seconds. The Device LED will blink twice to confirm the erasure. STEP3 To exit, press and hold both the [DEVICE] and [INPUT] buttons simultaneously until the Device LED blinks 3 times. J. Programming the All Off Button This allows you to program the All Off button so it can send up to three power On/Off commands with one button press. STEP1 Press the [CBL] button. STEP2 Press the [All OFF] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds. STEP3 Press the first [Device] button you want to store in the [ALL OFF] button and then the [POWER] button. Repeat this for other Device until you have stored all the desired power commands into the [ALL OFF] button. STEP4 Press the [CH5] button to save the power commands you stored. The [CBL] button will blink twice to confirm the Device have been saved. K. Programming for Advanced Functions. If your remote model has customprogrammable Macro buttons available, they can be programmed to act as a `Macro' or Favorite Channel button in CABLE mode. This allows you to program up to five 2-digit channels, four 3-digit channels or three 4-digit channels that can be accessed With one button press. *Note : The FAV button is not programmable if you have a Digital Cable Box made by Pace, Pioneer or CISCO/SA. STEP1 Press the [CBL] button to select the CBL mode. STEP2 Press the [MACRO] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds. STEP3 Enter the the 2, 3 or 4-digit code for the channel you want programmed first (for example, 007) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example, 050), then press the [STOP] button. Repeat this process for the third channel. The [CBL] button will blink once for each channel entered. STEP4 Press the [CH5] button to store the channels that were selected. The [CBL] button will blink twice to confirm the storage of commands. To access the programmed channels, press the [MACRO] button once. This will bring up the first channel. Press once again and it will bring up the second channel. Press again and it will bring up the third channel. To erase the Macro programming and return to the original function: STEP1 Press the [CBL] button to select the CABLE mode. STEP2 Press a [MACRO] button and the [OK/SEL] button simultaneously for 3 seconds. The CBL device LED will turn on for 30 seconds. The next step must be performed while the LED is on. STEP3 Press the [CH5] button to erase the functions stored in the button. The CBL device LED will blink twice to confirm that the memory button has been erased. L. Programming Volume Control Volume and Mute control are factoryprogrammed to automatically transfer to the respective Device mode you select, as follows: CBL : TV TV : TV DVD : TV If you wish to store the Cable volume control in CBL mode, use the following steps. STEP1 Press the [OK/SEL] button and [CBL] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on. STEP2 Press the [VOL5] button. The device LED will blink. STEP3 Press [CBL] button. The device LED will blink twice to confirm the programming. Note : To return CBL device to TV volume repeat steps above replacing [CBL] with [TV] in Step 3. M. Programming Channel Control Channel controls are factory-programmed to automatically transfer to the respective Device mode you select, as follows: CBL : CBL TV : CBL DVD : DVD If you wish to store the TV channel controls in TV mode, use the following steps. STEP1 Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on. STEP2 Press the [VOL6] button. The device LED will blink. STEP3 Press [TV] button. The device LED will blink twice to confirm the programming. Note : To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3. N. Low Battery Warning When the battery is low (2.3V-2.0V) and needs to be replaced with fresh batteries, device LED will blink 2 times in sequence whenever a [DEVICE] button is pressed to turn on equipment. O. Memory Lock System. This remote control is designed to retain programmed memory for 10 years -- even after batteries are removed from the remote control. For additional information about your remote control, go to www.universalremote.com 5 Set-up Code Tables CABLE TV Manufacturer/Brand Set-Up Code Number CISCO/SA EXPLORER Series 001 007 8600X 011 8600 021 8540,8570,8590 022 8500 023 LogicTV 209 U-VERSE 251 MOTOROLA DCT Series (DVR Model) 002 DTA100 206 U-VERSE,VIP1200,VIP1216,VIP1616T, 253 VIP1910, VIP1920, VIP1960, VIP1970 GENERALINSTRUMENT DCT Series,DCH Series, CFT2200 008 DL4,DQNV/DRX,DPBB,DPV/DP/DQN,DRZ 027 JERROLD BMC9012/BMC9022 006 DSR470 005 CFT2000 012 DL4,DQNV/DRX,DPBB,DPV/DP/DQN,DRZ 027 ADB ADB Series 254 255 ADB5810WX 315 ADB5810W, ADB5721WNX 259 AMINO Amigo 7X v2 235 A125, A130, A530 256 A110 260 A140, A540, A550 219 Amulet, Kamai 7XM, Kamai 7B 321 ARRIS MG5225,MP2000,MP2050A,MP2150A 172 Frontier 216 VIP5662W 140 AT&T U-VERSE 251 Bell Fibe Slim 2 229 BT Vision Vbox Series, DIT Series 232 YouView 960 Cincinnati Bell ZTE B700-V3 220 CISCO U-VERSE 251 RNG200 313 CIS330, CIS430 316 COMCAST RNG200 313 XFINITY 195 Cox Digital Cable Mini Box 223 DIGEO 2056-MSX 153 DigitalMultimediaTechnology DMT-205HD 222 DIGITAL STREAM DCS1000 180 Dish Network Hopper 3 122 DREAM DM7020S, DM7025, DM8000HD 159 Duoson TotalPlay 218 ENTONE Amulet IPTV Receiver 258 CABLE TV Manufacturer/Brand Set-Up Code Number 213 Kamai 651 221 Kamai 500 210 221 Kamai 45x 221 EVOLUTION FTA X0-01 158 EVOLUTION UNIVERSAL SD DTA 189 UNIVERSAL HD DTA 215 Foxtel IQ3 228 Horizon Ziggo 225 Humax 101-H 231 InnovativeSystems IPTV Receiver 262 KAON Mini 208 Layer3 C12516 226 MOXI MOXI MEDIA CENTER 006 MOXI HD DVR 052 2056-MSX 153 MYRIO IPTV Receiver 254 255 NAGRA DCI-4136M 211 NAGRAVISION HDDTA 201 NFUSION NUVENIOSDPHOENIX,NUVENIOHD, 192 SOLARIS, NOVA NOW TV NOW TV 314 Optimum Altice One 237 Optimum 236 PACE 500 Series 001 007 TDC Series 002 510 004 DC60X 206 IPH8005M 217 RNG200 313 Pico Digital VMX1, VMX3, HD-2 224 PIONEER VOYAGER Series 001 007 BA9000 013 SAMSUNG OCAP MODELS 001 007 SiDMedia DC7700X 200 SKY SKY+HD 230 SKY HD 204 Q 240 AP HD, AP Jr 241 Spectrum Spectrum 231 TECHNICOLOR 365 TELNET RC-RW100 154 Virgin Media TIVO 6 959 WEGENER IPTV Receiver 250 WINDSTERAM KINETIC 212 ZeeVee ZvMXE 227 TV Manufacturer/Brand Set-Up Code Number ADMIRAL 072 096 081 ADVENT 147 AIWA 141 145 AKAI 070 146 148 124 226 104 108 AKIO 103 ALARON 028 AMARK 112 AMERICA ACTION 043 AMPRO 073 ANAM 043 054 056 080 112 131 AOC 058 070 112 616 APEX 092 APEX DIGITAL 150 037 015 724 AQUAVISION 097 100 686 AUDIOVOX 076 103 043 035 078 224 AUVIO 689 Avera 761 AVIELO 090 AVION 223 AXESS 711 BAYSONIC 043 BELL&HOWELL 072 BENQ 234 BRADFORD 043 BROKSONIC 096 CANDLE 070 002 003 CAPEHART 058 CARVER 164 CELEBRITY 001 CETRONIC 043 CIELO Ciil CINERAL CITIZEN CLASSIC COBY 714 732 103 120 070 002 003 101 103 043 640 641 598 CONTEC 043 051 Continu-us 161 746 747 CRAIG 043 054 028 CROSLEY 164 CROWN 043 CURTIS MATHES 070 101 011 072 120 164 081 CXC 043 DAEWOO 076 103 112 043 120 TV Manufacturer/Brand Set-Up Code Number DELL 041 DENON 011 DIGITALPROJECTION 090 DUMONT 073 DWIN 131 132 DYNASTY 043 FISHER 007 057 ELECTROBAND 001 ELECTROHOME 024 076 ELEMENT 110 622 690 EMERSON 005 028 043 048 076 096 155 051 153 121 ENVISION 070 EPSON 087 228 ESA 031 Evervue 755 FREEMOTION 688 FUJITSU 164 197 028 149 FUNAI 028 043 052 168 FUSION 642 FUTURETECH 043 GATEWAY 165 031 GE 070 073 008 009 034 056 074 155 120 081 GEM 031 GIBRALTER 073 GOLDSTAR 106 112 GRUNPY 028 043 HAIER 116 623 598 749 HANNSPREE 099 HARLEYDAVIDSON 028 HARMANKARDON 164 HARVARD 043 HISENSE 198 021 619 630 598 752 749 HITACHI 011 598 007 009 072 010 012 023 HP HUMAX HYPERION HYUNDAI ILO 158 174 670 749 027 039 098 122 609 049 067 055 096 INFINITY 164 INFOCUS 046 215 225 233 726 733 INKEL 129 TV Manufacturer/Brand Set-Up Code Number INSIGNIA INTEQ JBL JCB JCPENNEY 068 069 078 096 164 168 604 617 073 164 001 008 024 030 070 101 156 JENSEN 013 JVC 038 001 034 083 639 KENWOOD 070 001 KLEGG KLOSS KREISEN KTV LG LODGENET 220 002 059 202 070 043 598 086 106 112 741 072 LOEWE 196 164 738 LOGIK 072 LXI 007 052 164 015 081 MAGNAVOX MAJESTIC MARANTZ MATSUI 070 003 022 059 060 061 164 094 056 028 035 211 205 218 050 138 232 072 164 070 143 169 164 MATSUSHITA 080 MAXENT 165 MEMOREX 007 072 028 096 MGA MIDLAND MINTEK MINUTZ MITSUBISHI MOTOROLA 024 070 073 077 008 024 040 146 028 124 200 235 081 081 MTC 070 101 MULTITECH 043 NAD 025 015 NEC NEXUS NIKEI NIKKO NIKO NORCENT 070 040 056 007 019 024 717 758 620 078 043 103 175 211 NTC 103 NUVISION 084 OLEVIA 219 TV Manufacturer/Brand Set-Up Code Number ONKING 043 onn. 898 ONWA 043 OPTIMUS 080 OPTOMA 029 OPTONICA 019 081 ORION 096 201 203 204 205 028 PANASONIC 080 164 190 034 056 230 248 524 607 664 801 PEERLESS-AV 723 763 PHILCO 070 003 024 056 059 060 164 PHILIPS 164 005 218 038 093 070 003 059 199 232 727 743 773 PIONEER 023 025 135 176 018 070 183 191 214 PLANAR 728 742 787 788 POLAROID 026 118 119 006 110 PORTLAND 103 PRISM 034 PROSCAN 722 PROTON 058 171 163 PROTRON 102 213 115 PROVIEW 110 PROX 092 QUASAR 034 056 606 RADIO SHACK 019 043 RCA 156 070 023 024 056 074 209 081 713 751 REALISTIC 007 019 REVOLUTION HD 220 RUNCO 072 073 216 697 SAMPO 070 058 165 SAMSUNG 192 184 185 101 133 089 105 070 655 SANSEI 120 SANSUI 096 078 762 SANYO 007 053 057 020 750 SCEPTRE 036 699 SCOTT 005 028 043 048 113 Sealoc 897 SEARS 007 028 030 057 094 052 164 015 SEIKI 690 SEMIVOX 043 SEMP 015 SEURA 704 797 SHARP 081 598 684 019 028 022 692 735 765 766 SHERWOOD 128 TV Manufacturer/Brand Set-Up Code Number SIGNATURE 072 Silo 001 Skyvue 744 Skyworth 895 SONY 001 608 633 SOUNDESIGN 003 028 043 SOYO 163 SPECTRICON 112 SQUAREVIEW 052 SSS 043 STARLITE 043 SUPRE MACY 002 SUPREME 001 SUNBRITE 633 634 635 236 605 772 SVA 046 SYLVANIA 070 003 059 060 164 056 168 121 231 SYMPHONIC 052 168 SYNTAX OLEVIA 219 TANDY 081 TATUNG 056 TCL 705 749 TECHNICS 034 080 TECHNOL ACE 028 TECHVIEW 246 TEKNIKA 002 003 024 028 043 072 101 103 164 TELERENT 072 TERA 172 THOMPSON 166 TNCI 073 TOSHIBA 015 101 045 030 007 040 142 137 703 TRUTECH 212 UNIVERSAL 008 009 UPSTAR 708 VENTURER 721 VIDEO CONCEPTS 146 VIDIKRON 164 VIEWSONIC 210 211 720 VIORE 055 229 192 VISCO 110 VIZIO 236 031 624 625 WARDS 164 008 009 019 028 060 061 072 074 070 W Box Technologies 731 WESTINGHOUSE 076 036 221 222 001 690 695 WINBOOK 079 TV Manufacturer/Brand Set-Up Code Number YAMAHA YUPITERU ZENITH ZONDA 070 043 011 072 073 095 103 096 112 DVD Manufacturer/Brand Set-Up Code Number ADCOM 203 AIWA 210 AKAI 239 APEX DIGITAL 240 196 ARCAM 165 148 374 BOSE 244 245 CAMBRIDGEAUDIO 224 145 COBY 206 CYBERHOME 170 212 DAEWOO 170 DENON 226 225 358 DURABRAND 235 EMERSON 235 ESA 235 FUNAI 235 GOLDSTAR 182 194 GO VIDEO 228 182 252 253 254 GRADIENTE 243 HARMANKARDON 217 HITACHI 181 INSIGNIA 235 085 182 178 349 385 INTEGRA 236 128 JVC 185 KENWOOD 166 KISS 237 KLH 230 KOSS 243 KRELL 218 LEXICON 216 LG 182 194 105 350 MAGNAVOX 178 191 195 235 386 MARANTZ 135 MCINTOSH 167 MEMOREX 222 MERIDIAN 200 MINTEK 240 196 MITSUBISHI 186 DVD Manufacturer/Brand Set-Up Code Number MYRYAD 211 NAD 198 182 353 ONKYO 207 236 128 OPPO 125 OPTIMUS 187 ORITRON 243 PANASONIC 076 219 103 104 379 PHILIPS 195 164 191 209 127 381 387 PIONEER 187 221 223 354 377 POLAROID 085 RCA 086 SANSUI 201 SANYO 215 SAMSUNG 183 228 205 073 152 241 380 SENSORYSCIENCE 254 SHARP 174 SHERWOOD 129 361 SONY 168 190 213 077 118 119 120 121 126 351 368 378 382 SPECTRONIQ 088 SUPERSCAN 235 SV2000 235 SYLVANIA 235 SYMPHONIC 235 TASCAM 185 TAG McLaren 202 THETA DIGITAL 187 TOSHIBA 169 191 206 227 201 236 356 TRUTECH 151 VENTURER 229 VINC 220 087 VIZIO 375 YAMAHA 199 204 246 372 334 383 ZENITH 182 194 DVR(TIVO) Manufacturer/Brand Set-Up Code Number CHANNELMASTER 841 859 DSTV 786 787 788 241 800 HUGHES 817 HUMAX 817 ICREALTIME 111 816 MOXI 112 PHILIPS 790 817 785 DVR(TIVO) Manufacturer/Brand Set-Up Code Number RCA 809 REPLAYNETWORKS 775 SONY 804 805 SpecoTechnologies 879 TIVO 790 817 858 TOSHIBA 817 ZUUMMedia 855