Vollrath Operator's Manual

Safety Precautions

To ensure safe operation, read the following statements and understand their meaning. This manual contains safety precautions which are explained below. Please read carefully.

[Warning] Warning is used to indicate the presence of a hazard that will or can cause severe personal injury or death.

[Caution] Caution is used to indicate the presence of a hazard that will or can cause minor or major personal injury if the caution is ignored.

NOTICE: Notice is used to note information that is important but not hazard-related.

To reduce risk of injury or damage to the equipment:

• This equipment must be installed by a qualified person.
• Use only grounded electrical outlets that match the rated voltage on the nameplate.

NOTICE: Do NOT modify the cord or plug on the drop-in. Modifying any component may damage the drop-in or cause injury, and will void the warranty. See the specification sheet on Vollrath.com for electrical specifications.

• Do not use an extension cord with this equipment. Do not plug this equipment into a power strip or multi-outlet power cord.
• This equipment should only be used in a flat, level position.
• Do not spray the controls or the outside of equipment with liquids or cleaning agents.
• Keep the equipment and power cord away from open flames, electric burners or excessive heat.
• Do not use food pans deeper than 6" (15.2 cm).
• Not for use with plastic pans.
• Do not operate equipment if it is damaged or malfunctioning.
• Do not operate unattended.
• Unplug and allow the equipment to cool before cleaning or moving.
• Do not clean this equipment with steel wool.

Product Specifications

Function and Purpose

This drop-in is intended and designed to hold containers of food at proper serving temperatures. Hot food stations are not intended or designed to cook raw food or to reheat prepared food. Food must be prepared and placed in food stations at proper serving temperatures. This equipment is not intended for household, industrial or laboratory use.

Please register your product at Vollrath.com/ProductRegister

Features and Controls

Diagram Description: The unit features three main components labeled A, B, and C.

• A THUMBSCREW: Secures the drop-in to the mounting surface.
• B TEMPERATURE CONTROL: Used to set or adjust the temperature of the well. The larger the number the higher the temperature, the smaller the number the lower the temperature. The "0" position is off.
• C POWER INDICATOR LIGHT: Illuminates when the well is in the heating mode.

Operation

[Warning] Electrical Shock Hazard: Keep water and other liquids from entering the inside of the unit. Liquid inside the unit could cause an electrical shock. Do not overfill pans or trays. Liquid could contact the electrical components and cause a short circuit or an electrical shock.

[Caution] Burn Hazard: Do not touch hot food, liquid, or heating surfaces while equipment is heating or operating.

Notices: Do not use food pans deeper than 6" (15.2 cm). Do not use plastic pans.

1. Plug electrical power cord into an outlet that matches the rated voltage on the nameplate.
2. Turn the temperature control to the maximum heat setting. Cover the well(s). Preheat for 30 minutes.
3. Place containers of hot food, above 140 °F (60 °C), into preheated equipment.
4. Reduce heat setting to a level that will maintain a safe holding temperature and maintain food quality.
5. Use gloves, mitts, or pot holders to protect hands when removing hot food containers.

Notice: Monitor food temperature closely for food safety. The United States Public Health Service recommends that hot food be held at a minimum of 140 °F (60 °C) to help prevent bacteria growth.

Cleaning

[Caution] Burn Hazard: Hot surfaces and food can burn skin. Allow the hot surfaces to cool before handling.

To maintain the appearance and increase the service life, clean your equipment daily.

Notice: Do not use caustic cleaning chemicals, steel wool, or commercial lime removal products to clean the equipment. Thoroughly rinse equipment with water after cleaning.

1. Remove hot food containers. Use gloves, mitts, or pot holders to protect hands.
2. Turn the temperature control to the "0" setting.
3. Unplug the drop-in.
4. Allow the drop-in to cool completely.
5. Remove the shield from the bottom of the well.
6. Hand wash the shield in soapy water.
7. Dry the shield.
8. Use a damp cloth or sponge dipped in soapy water to clean the inside of the well and the outside of the equipment.
9. Use a damp cloth or sponge to thoroughly wipe off the soapy water.

Troubleshooting

Service and Repair

Serviceable parts are available on Vollrath.com. To avoid serious injury or damage, never attempt to repair the unit or replace a damaged power cord yourself. Do not send units directly to The Vollrath Company LLC. Please contact Vollrath Technical Services for instructions. When contacting Vollrath Technical Services, please be ready with the item number, model number (if applicable), serial number, and proof of purchase showing the date the unit was purchased.

Warranty Statement

This warranty does not apply to products purchased for personal, family or household use, and The Vollrath Company LLC does not offer a written warranty to purchasers for such uses.

The Vollrath Company LLC warrants the products it manufactures or distributes against defects in materials and workmanship as specifically described in our full warranty statement. In all cases, the warranty runs from the date of the end user's original purchase date found on the receipt. Any damages from improper use, abuse, modification or damage resulting from improper packaging during return shipment for warranty repair will not be covered under warranty.

For complete warranty information, product registration and new product announcement, visit www.vollrath.com.

Contact Information

The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI 53081-3201 U.S.A.

Main Tel: 800.624.2051 or 920.457.4851

Main Fax: 800.752.5620 or 920.459.6573

Customer Service: 800.628.0830

Canada Customer Service: 800.695.8560

Technical Services: techservicereps@vollrathco.com

Website: www.vollrath.com