User Manual for SAMSUNG models including: ACAU711R, A3LACAU711R, ACAU711R Bluetooth 5.2 IoT Module, ACAU711R, Bluetooth 5.2 IoT Module, 5.2 IoT Module, IoT Module
Samsung Electronics Co Ltd ACAU711R A3LACAU711R A3LACAU711R acau711r
File Info : application/pdf, 11 Pages, 1.44MB
DocumentDocumentUser manual for ACAU711R 3. Operational Description ACAU711R is the 802.11a/b/g/n/ax +Bluetooth 5.2 IoT Module that acts as a communication controller for users of a wireless device to connect to SMART Home - Features >IEEE 802.11ax Draft compliant. >Dual-band 2.4GHz /5 GHz >Dual-stream spatial multiplexing up to 114Mbps data rate >On-chip power amplifiers and low noise amplifiers for both bands >Complies with Bluetooth Core Specification Version 5.2 >Supports BT/Wi-Fi coexistence. >Adaptive frequency hopping (AFH) for reducing radio frequency interference - Time base of the RF frequency For IF and RF frequency, 40MHz crystal is a clock reference. - Synthesizer Synthesizer inside Transceiver. Internal voltage controlled oscillator (VCO) provides the desired LO signal base on the phase-locked loop (PLL) with a relatively wide tuning range for this application. Internal fractional nPLL allows support for a wide range of reference clock frequencies - Wi-Fi Transmission Baseband data is modulated and up converted to the 2.4GHz ISM and 5-GHz U-NII bands, respectively. Linear on chip power amplifier are included, which are capable of delivering high output powers while Meeting IEEE802.11ax and IEEE802.a/b/g/n specifications without the need for external PAs. - Wi-Fi Receiver The SDA8702PAH has a wide dynamic range, direct conversion receiver that employs high-order on-chip channel filtering to ensure reliable operation in the noisy 2.4GHz ISM band or the entire 5GHz U-NII band .Control signals are available that can support the use of optional LNAs for each band,which can increase the receive sensitivity by several decibels. Reverse direction isolation of LNA inside Transceiver IC suppresses unwanted radiation. -Bluetooth Low Energy The ACAU711R support the Bluetooth5.2 LE and 5.2 BLE 2Mbps Version 1.0 XuGuang Tech page 2 of 4 4. Product Details -Data Modulation DSSS:CCK,BPSK,QPSK for 802.11b OFDM:BPSK,QPSK,16QAM,64QAM,256QAM for 802.11a,g,n,ax FHSS:GFSK,OQPSK, 8DPSK, /4DPSK for Bluetooth -Frequency Range 2412-2484MHz 5180-5885MHz -Output Power tolerance Output power ± 1dBm -Recommended Operating conditions Operating voltage Operating -Max target Power e.i.r.p. 18 dBm Min Typ. Max Unit 2.97 3.3 3.63 V -20 25 85 °C -Power DC 5, 12V Version 1.0 XuGuang Tech page 3 of 4 Approval Statement FCC approval statement RF Software restrictions 1. Contention-Based Protocol, as demonstrated in the FCC test report, is permanently embedded in the module and is not host-dependent and can' t be changed by anyone. 2. Operation of transmitters in the 5.25-5.35GHz, 5.47-5.725GHz bands in this Modular device will only associate and connect with a low-power indoor access point or subordinate device and never directly c onnect to other client devices. This feature is included in its firmware and can't be changed by anyone. 3. Operation of transmitters in the 5.25-5.35GHz, 5.47-5.725GH bands in this Modular device will always initiate transmission under t he control of a low-power indoor AP or subordinate except for brief trans missions before joining a network. These short messages will only occur if the client has detected an indoor AP or subordinate operating on a cha nnel. These brief messages will have a time-out mechanism such that if it does not receive a response from an AP it will not continually repeat th e request. This device complies with Part 15 of the FCC`s Rules. Operation is subje ct to the following two Conditions: 1.This device may not cause harmful interference. 2.This device must accept any interference received, including interference that may cause undesirable operation. To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end-product. Contains Transmitter module FCC ID: A3LACAU711R This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These lim its are designed to provide reasonable protection against harmful interfere nce in a residential installation. This equipment generates, uses and can r adiate radio frequency energy and, if not installed and used in accordanc e with the instructions, may cause harmful interference to radio communi cations. However, there is no guarantee that interference will not occur in a partic ular installation. If this equipment does cause harmful interference to radi o or television reception, which can be determined by turning the equipm ent off and on, the user is encouraged to try to correct the interference b y one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. -The OEM integrator is responsible for ensuring the end-user has no man ual instruction to remove or install module. -The module is limited to installation in mobile or fixed applications. FCC Caution: Any changes or modifications not expressly approved by th e party responsible for compliance could void the user's authority to oper ate this equipment. This device meets all the other requirements specified in Part 15E, Sectio n 15.407 of the FCC Rules. -RF exposure considerations The module has been certified for integration into products only by OEM integrators under the following condition: -The antenna(s) must be installed such that a minimum separationdistance of at least 20cm is maintained between the radiator(antenna) and all pers ons at all times. -The transmitter module must not be co-located or operating in conjunctio n with any other antenna or transmitter except in a ccordance with FCC multi-transmitter product procedures. This device can support Ad-hoc and Wi-Fi Direct for 2.4GHz, UNII 1, and UNII 3 bands. The device operates strictly as a client in DFS channels (with passive sca n). It does not support ad-hoc, Wi-Fi Direct Group Owner, Hotspot, or any other peer-to-peer modes that may initiate a network in DFS channels (U NII2-2A and UNII2-2C band) <Regulatory notice to host manufacturer according to KDB 996369 D03 OEM Manual v01> List of applicable FCC rules This module has been granted modular approval as below listed FCC rule parts. -FCC Rule parts 15C (15.247, 15.407) Summarize the specific operational use conditions -The OEM integrator should use equivalent antennas which is the same type and equal or less gain then an antenna which installed an original module. RF exposure considerations The module has been certified for integration into products only by OEM integrators under the following condition: - The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. - The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. - Mobile use As long as the three conditions above are met, further transmitter testing will not be required. OEM integrators should provide the minimum separation distance to end users in their endproduct manuals. OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requiremen ts of the FCC rule such as FCC Part 15 Subpart B before it can be place d on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC r ules. This module must not be incorporated into any other device or syst em without retesting for compliance as multi-radio and combined equipme nt. IMPORTANT: The final host product must have an integral antenna that is not removable by the end user. Canada IC approval statement IC approval This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exe mpt RSS(s). Operation is subject to the following two conditions: (1) This device may not causeinterference. (2) This device must accept any interference, including interference that m ay cause undesired operation of thedevice. L'émetteur/récepteur exempt de licencecontenudans le présentappareilestco nforme aux CNR d'Innovation, Sciences et Développementéconomique Can ada applicables aux appareils radio exempts de licence. L'exploitationesta utorisée aux deux conditions suivantes : (1) L'appareil ne doit pas produire debrouillage; (2)L'appareildoitaccepter toutbrouillageradioélectriquesubi, mêmesi le brouil lageest susceptible d'encompromettre lefonctionnement. Caution: Any changed or modifications not expressly approved by the par ty responsible for compliance could void the user`s authority to operate t his equipment. Attention: Toutechangéou modifications non expressémentapprouvéspar la partieresponsable de la conformitépourraientannulerl'utilisateur `autorité de faire fonctionnercetéquipement. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the foll owing: "Contains IC: 649E-ACAU711R" any similar wording that expresses the same meaning may be used. l'appareil hôte doit porter une étiquette donnant le numéro de certification du module d'Industrie Canada, précédé des mots (Contient un module d' émission , du mot IC: 649E-ACAU711R) ou d'une formulation similaire exp rimant le même sens, comme suit The device for operation in the band 5150-5250 MHz is only for indoor us e to reduce the potential for harmful interference to co-channel mobile sat ellite systems. Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés u niquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les m êmes canaux; User should also be advised that high-power radars are allocated as prim ary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LELAN devices. Les utilisateurs doivent également être informés que les radars de haute puissance sont affectés aux bandes 5250 - 5350 MHz et 5650 - 5850 MHz en tant qu'utilisateurs principaux (c. - à - D. utilisateurs prioritaires) et qu e ces radars peuvent causer des interférences et / ou des dommages à l' équipement le - lan. The device meets the exemption from the routine evaluation limits in sect ion 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité à l'exposition de RSS-102 RF, utilisateurs peut obtenir l'information canadienne surl'exposition et la conf ormité de RF. This transmitter must not be co-located or operating in conjunction with a ny other antenna or transmitter. This equipment should be installed and o perated with a minimum distance of 20 centimeters between the radiator and your body. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temp s qu'aucune autre antenne ouémetteur. Cet équipement devrait être install é et actionné avec une distance minimum de 20 centimètres entre le radi ateur et votre corps. IMPORTANT: The final host product must have an integral antenna that is not removable by the end user. > Frequency Range: 2412-2472MHz, 5180-5825MHz > RF power output 17.0 13.0 13.0 13.0 > Output Power tolerance Output power +/-1dB Approval Statement Europe CE approval statement Restircted countries : 5150-5350MHz indoor use only. This transmitter must not be co-located or operating in conjunction with a ny other antenna or transmitter. This equipment should be installed and o perated with a minimum distance of 20 centimeters between the radiator and your body. CE RED_EU declaration This product can be used in which EU members, in accordance with Article 10(10) / or this product can be used in at least one EU country, in accordance with Article 10(2)Microsoft: Print To PDF