Home - Antari Lighting And Effects
User Manual for Antari models including: MB-20X, Mobile Fog Machine, MB-20X Mobile Fog Machine, Fog Machine
DOWNLOAD - Antari Lighting And Effects
MB-20X User Manual - Antari Lighting And Effects
File Info : application/pdf, 16 Pages, 3.77MB
DocumentDocumentMB-20X MOBILE FOG MACHINE User Manual - ENGLISH © 2022 Antari Lighting and Effects Ltd. 1 © 2022 Antari Lighting and Effects Ltd. www.antari.com ! ! 2 © 2022 Antari Lighting and Effects Ltd. www.antari.com Safety Information - ENGLISH- Please read the following safety information carefully before operating the machine. This information includes important safeguards about installation, usage, and maintenance. Pay attention to all warning labels and instructions in this manual and printed on the machine. If you have questions about how to operate the machine safely, please contact your local Antari dealer for help. Keep this device dry. Always connect to a grounded circuit to avoid risk of electrocution. Do not operate if power cord is damaged. If power cord is damaged, replace it immediately with a new one of same power rating. Remove the machine from battery or power adaptor before servicing and when not in use. This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled, remove machine from battery or power adaptor and clean with a damp cloth. If fluid is spilled onto electronic parts, immediately unplug the machine and contact your local Antari dealer for advice. No user serviceable and modifiable parts inside. Never try to repair this product, an unauthorized technician may cause damage or malfunction to the machine. For adult use only. Never leave the machine running unattended. For persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, supervision or instruction must be given concerning use of applicance in a safe way and understand the hazards involved. Install the machine in a well-ventilated area. Provide at least 50 cm space around the machine. 3 © 2022 Antari Lighting and Effects Ltd. www.antari.com Never add flammable liquid of any kind to the machine. Make sure there are no flammable materials close to the machine while operating. Only use Antari fluid. Other fluid may lead to heater clog and malfunction. If the machine fails to work, unplug the machine and stop operation immediately. Contact your local Antari dealer for advise. Before transporting the machine, make sure the fluid tank is completely drained. Fog fluid may present health risks if swallowed. Do not drink fog fluid. Store it securely. In case of eye contact or if fluid is swallowed, immediately look for medical advice. Do not charge battery while using, even if battery is low. Remove head unit or make sure head unit's power switch is off before charging. Unpacking and Inspection Immediately upon receiving the machine, carefully unpack the carton, check the content to ensure that all parts are present and have been received in good condition. If any parts appear damaged or mishandled from shipping, notify the shipper immediately and retain the packing material for inspection. What is included: 1 x MB-20X Fog Machine 1 x Battery base 1 x Battery charger 1 x FLM-05P water-based liquid 1 x User Manual 1 x Flightcase 4 © 2022 Antari Lighting and Effects Ltd. www.antari.com Product Dimensions 238 mm 108 mm Product Overview ON / OFF Switch Control Fog Output Nozzle Dip Switch 293 mm Wire Remote Socket Wireless Receiver Socket Output Level Adjustment Knob Main Power Switch XLR 3-Pin DMX Connector Lock lever Charger Input 5 © 2022 Antari Lighting and Effects Ltd. www.antari.com MB-20S Power Base (Optional) Power Input Setting Up DO NOT CHARGE THE BATTERY WHILE MAKING FOG OR SWITCH IS ON Step 1: Place the machine on a flat surface and in a suitably large area with at least 50 cm of open space around the machine. Step 2: Fill the fluid tank with Antari FLM-05P fluid. Step 3: Charge the battery by plugging the charger adaptor into a grounded electrical outlet. Yellow light on the adaptor indicates charging, when it turns green then the charge complete. Please note the battery requires 3 hours charge time. A fully charged battery can run the machine for roughly 12 minutes. Plug in the charger Red indicates charging Green indicates charging complete 6 © 2022 Antari Lighting and Effects Ltd. www.antari.com Always connect the machine to a protected circuit and ensure it is properly grounded to avoid risk of electrocution. Step 4: Connect the battery base or power base to the machine. Turn on the machine to start operation. Pull to release locking lever Align and insert head unit to base 7 © 2022 Antari Lighting and Effects Ltd. www.antari.com Step 5: To start making fog, locate the rotary knob on the back for output level adjustment, and press the button to start making fog, release to stop. Step 6: To turn off the machine, disconnect the machine (head-unit) from the battery base or power base. Operation Control Panel Operation The machine can be operated with the On/Off button and output level control knob located on the rear. When using On/Off Mode press and hold the button to make fog, release to stop. In Continuous Mode, press button once to produce fog, press again to stop. Dip Switch 12 OFF ON Function On/Off Mode Continuous Mode Rotary Knob SMOKE Function Turn fog on/off, adjust output volume from 0~100% DMX Connector Pin Assignment The machine provides 3-pin XLR connectors for DMX connection. The diagram below indicates pin assignment information. 8 © 2022 Antari Lighting and Effects Ltd. www.antari.com Pin Function 1 Ground 2 Data- 3 Data+ DMX Operation Making the DMX Connection Connect machine to a DMX controller or to one of the machines in the DMX chain. The machine uses a 3-pin XLR connector for DMX connection, the connector is located on the rear of the machine. Address Setup Use the DIP switch located on the rear of the machine to set the DMX address. The machine occupies 1 control channels. The starting address is defined as the first channel from which the machine will respond to the controller. Always double check to make sure there are no overlapping channles in order to control the machine correctly. DMX Channel Function Channel 1 Fog DMX Value Range 0 4 5 255 Function Fog Off Output 1-100% 9 © 2022 Antari Lighting and Effects Ltd. www.antari.com Z-3 Remote Control Operation (Optional) To operate the machine by remote control, connect the remote to the microphone jack located on the rear of machine. Use the switch to turn fog on/off, and use the rotary knob to adjust the output volume from 0~100%. WTR-20 Wireless Operation (Optional) Wireless remote control system WTR-20 consists of a transmitter equipped with four buttons to activate, deactivate, increase and decrease fog output and an onboard receiver attached to the rear panel of MB-20X fog machine. W-2 Wireless Transmitter Press [A] button to emit fog. Press [B] button to stop. Press [C] button to increase output volume. Press [D] button to decrease output volume. In a an unobstructed open space the effective distance is 50 meters, usage depending on obstacle level has an effective distance is 10-25 meters. 10 © 2022 Antari Lighting and Effects Ltd. www.antari.com Registering a transmitter Transmitters can be paired or deleted from the receiver. Each receiver can pair up to 5 transmitters. Follow the steps below to pair or delete a transmitter from a receiver. To Pair Step 1: Put Dip switch 11 to ON position Step 2: LED indicator will start blinking, press and hold [A] to pair Step 3: Once pairing complete LED indicator will be constant on for 3 seconds Step 4: Put Dip switch 11 back to OFF position to start operation. To Delete Step 1: Put the dip switch 10 to ON position Step 2: LED indicator will start blinking, press and hold [A] to delete Step 3: The deleting process will take approximately 10 seconds Step 4: Once deleted, the LED indicator will be on for 3 seconds Step 5: Put the dip switch 10 back to the OFF position to start operation Transmitter battery replacement If the effective distance seems to decrease, it is possible the battery level is low and requires replacement. In order to replace the battery, undo the three screws on the back of transmitter to release the cover. Replace with the same type and specification of battery which is 27A 12V Fluid Only use Antari FLM-5P water-based liquid for the MB-20X Fog Machine. The machine is tested and calibrated with this liquid to get the best output performance. Warranty will be voided if any other type of liquid is used. Improper use of liquid may lead to machine failure or malfunction. 11 © 2022 Antari Lighting and Effects Ltd. www.antari.com Service and Maintenance Do not allow the machine to become contaminated. Remove dust from air vents with air compressor, vacuum or a soft brush. Only use a damp cloth to clean the casing. Before storing run distilled water through the system to help avoid condensing the pump or heater. It is recommended to run the machine on a monthly basis in order to achieve best performance and output condition. Excessive dust, liquid and dirt built up will degrade performance and cause overheating. LED Status Indicator Status Standby/Ready Producing fog Producing fog via DMX Low Battery Heat Element Failed LED Indicator Constant on Slow flash Alternate quick and slow flash Slow Flash (approximately 1 flash per second) Quick Flash (approximately 4 flashes per second) Maintenance of Rechargeable lead-acid Battery To give the rechargeable battery long lifespan and best performance, please follow below instructions: Please fully charge the battery upon receipt of the machine and before and after each operation. Battery will self-discharge bit by bit if not in use. To avoid over discharging problem, every 2-4 weeks, check and ensure the battery has sufficient power to work. At least charge the battery to full every 2-3 months. Before storage, please have the battery fully charged. Please store the fully charged battery and the machine in cool and dry area, avoid 12 © 2022 Antari Lighting and Effects Ltd. www.antari.com directly sunlight. Please charge the battery within 1 hours if the battery is going to run out of power. Battery capacity changes as temperature differs. Life and capacity of battery is rated at 25°C, ambient temperature and humid change will significantly affect battery life. If you have any question on maintenance and usage, please contact your local dealer for advice. Technical Specifications - Input voltage - Rated power - Warm-up time - Fluid consumption - Fluid tank capacity - Compatible fluid - Ambient temp. range - Control - DMX channels - Connection - Optional accessories - Dimension - Weight DC 12V (Battery) AC 100-240V, 50-60Hz (Battery charger) 600W 1 second (approx.) 16 ml/min 0.4l (0.11gal) Antari FLM-5P Fog Fluid 0 °C - 40 °C (32 °F-104 °F) DMX512, Manual, Wireless (Optional) Cable Remote (Optional) 1 channel XLR 3-pin (DMX) WTR-20 Wireless Remote Z-3 Cable Remote MB-20S Power Base L293 W108 H238 mm (L11.54 W4.25 H9.37 inch) 8.5 kg (18.74 lbs) 13 © 2022 Antari Lighting and Effects Ltd. www.antari.com 14 © 2022 Antari Lighting and Effects Ltd. www.antari.com © 2022 Antari Lighting and Effects Ltd. www.antari.com = C08M1B60205 © 2022 Antari Lighting and Effects Ltd. www.antari.com