Milesight | 5G, AI, IoT and LoRaWAN®Download Center
User Guide for Milesight models including: B6601 AI Pro Bullet Plus Network Camera, B6601, AI Pro Bullet Plus Network Camera, Bullet Plus Network Camera, Plus Network Camera, Network Camera, Camera
The steps to change the IP of cameras are as below: 1) Start Smart Tools, click the IPC Tools page, then enter the device information, such as IP address, MAC ...
il y a 17 heures — The steps to change the IP of cameras are as below: 1) Start Smart Tools, click the IPC Tools page, then enter the device information, such as IP address, MAC ...
File Info : application/pdf, 8 Pages, 18.93MB
DocumentDocumentAI Pro Bullet Plus Network Camera User Manual Smart Tools All Software & files can be downloaded from https://www.milesight.com/resources/download-center Milesight IP VIDEO SURVEILLANCE Table of Content 1. Quick Installation Steps.............................................................................................. 2 2. Hardware Overview................................................................................. 5 3. How to Connect to Alarm Interface........................................................................... 9 4. How to Connect the Water-proof Connector.......................................................... 9 5. Assigning an IP Address by Using Smart Tools....................................................10 6. Assigning an IP Address via Browser........................................................................11 7. Accessing from the Web Browser.............................................................................. 11 www.milesight.com 1. Quick Installation Steps Step1: Fix a sticker on the position where the camera is intended to be installed; 150mm Note: For 5G camera, you need to install the four 5G antennas before installing the front cover to the rear cover or attaching the camera to the bracket. LoRa Antenna 5G Antenna 150mm Step2: Remove the tension disc on the rear cover of the Junction Box (A62), and cut an opening on the rubber plug and get cables through the opening then fasten the rear cover to the ceiling or wall; Step4: Adjust the cables length, and connect the cables to corresponding interfaces and fix the tension disc. Close the junction box and fix screws at last. Please remember to plug the small rubber plug whenever the holes on the rubber plug is not in use; Step3: Install the front cover from the angle near 90° to the rear cover or hang the camera to the bracket; Tension Disc Rubber Plug Rubber Plug Network Cable Power Cable 12 2 www.milesight.com Remember to fix the setscrew tightly. Step5: Adjust the shooting direction by adjusting the screws as shown in the diagram. Once the camera direction is adjusted, tighten the setscrew to secure the camera orientation. 360° 360° 90° www.milesight.com 3 13 Step6: Take out the mounting screws from the accessory pack and use them to secure the bracket. Adjust the camera angle as desired before finally tightening the bracket. Note: 1) Loosen the screws to get access to the SD card slot if you need. Fix the screws again after inserting the SD card. 2) For 5G camera, the card slot is used to insert the SIM card. And the SD card slot is located inside the camera body. The replacement of SD card requires disassembling the camera. SIM SIM Card Slot Reset SD Card Slot 2. Hardware Overview microSD/SDHC/SDXC Card Slot (Nano SIM Card Slot For 5G Camera) Reset Auto Focus Camera Lens IR LEDs Light Sensor 12 4 www.milesight.com www.milesight.com 5 13 Motorized Camera Light Sensor Lens IR LEDs Ethernet Port (PoE) Alarm/Audio Radar AI LPR Pro Bullet Plus Camera DC 12V Radar 16 www.milesight.com 5A AI Pro Bullet Plus Camera 5G Antenna 5G AIoT Pro Bullet Plus Camera LoRa Antenna 5G Antenna Supplement Light AI LPR 4X Pro Bullet Plus Camera White LED Light www.milesight.com IR LED Light 71 Audio I/O Alarm I/O DC 12V Wiegand Interface RS485 Ethernet Port Supplement Light AI LPR Motorized Pro Bullet Plus Camera White LED Light IR LED Light Audio I/O Alarm I/O DC 12V Wiegand Interface RS485 Ethernet Port(PoE) 18 www.milesight.com Note: 1) Reset Button: Press "Reset" button for 5 seconds, then the device will be restored to factory default; 2) DC and PoE are available for AI Pro Bullet Plus Camera's power supply. (PoE is not available for Supplement Light AI LPR 4X Pro Bullet Plus Camera.) 3. How to Connect to Alarm Interface Digital output Digital input PIN1 General I/O Terminal Block PIN2 PIN3 PIN4 12V PIN1: Alarm Output NC/NO 24V DC 1A PIN2: Alarm Output NC/NO 24V DC 1A PIN3: Alarm Input NC/NO 12V PIN4: Alarm Input NC/NO 12V 4. How to Connect the Water-proof Connector LAN Rubber ring Screw bolt Screw nut Network Port Connector O-Ring www.milesight.com 91 Step1: Get the network cable through the screw nut, rubber ring and the screw bolt; Step2: Insert the rubber ring into the screw bolt; Step3: Connect the screw nut to the screw bolt; Step4: Place the O-Ring on the network port connector; Step5: Connect the RJ45 to the network port connector, tighten the screw bolt and the connector. Note: Please tightly wrapped all cable-out interface with adhesive tape at last to prevent them from water. 5. Assigning an IP Address by Using Smart Tools Smart Tools is a software tool which can automatically detect multiple online Milesight network cameras in the LAN, set IP addresses, and manage firmware upgrades. It's recommended to use when assigning IP addresses for multiple cameras. The steps to change the IP of cameras are as below: 1) Start Smart Tools, click the IPC Tools page, then enter the device information, such as IP address, MAC address, Port number, Netmask, and Gateway, then all related Milesight network cameras in the same network that will be shown. 2) Select a camera or multiple cameras according to the MAC addresses. 3) Click "Activate" to set the password when using the cameras for the first time (Password must be 8 to 32 characters long, contain at least one number and one letter), and set three security questions (If you forget the password, you can reset the password by answering three security questions correctly). 4) Type the user name and password you set, change the IP address or other network values, and then click "Modify" button. 5) By double clicking the selected camera or the browser of interested camera, you can access the camera via web browser directly. More usage of Smart Tools, please refer to the "Smart Tools User Manual". 6. Assigning an IP Address via Browser If the network segment of the computer and that of the camera are different, please add some 192.168.5.xx(255.255.255.0) for your PC to get access to your cameras, more details can be found on "Milesight Network Camera Quick Start". 7. Accessing from the Web Browser The camera can be used with the most standard operating systems and browsers. The recommended browsers are Internet Explorer, Firefox, Chrome, Safari. More information about the plugin installation, please refer to the troubleshooting: 5. Milesight-Troubleshooting-Plugin Installation on Windows-IPC 6. Milesight-Troubleshooting-Plugin Installation on MAC 1 10 www.milesight.com www.milesight.com 11 1 AI Pro Bullet Plus Thank you for choosing Milesight Product www.milesight.com