Support | Icom Inc.
Instructions for ICOM models including: CT-M500, Wireless External Interface Box, External Interface Box, Wireless Interface Box, Interface Box, Box
Icom CT-M500 Wireless Interface Box [CTM500 11] - IPX7Dimensions (W x H x D) - 6.2" x 2.7" 3.2" (15.7 x 6.76 x 8.21 cm)Weight - 15.2 oz (430 g)*Sold as an Individual Specifications:Type: PartsBox Dimensions: 3"H x 8"W x 9"L WT: 1.8 lbsUPC: 731797036940
Icom CT-M500 Wireless Interface Box [CTM500 11] — MarinePartsDirect.com
File Info : application/pdf, 2 Pages, 445.08KB
DocumentDocumentInstalling You can mount the device on a dashboard using the universal mounting bracket supplied with your device. CAUTION: · KEEP the device at least 1 meter (3.3 ft) away from the vessel's magnetic navigation compass. · INSTALL the device within approximately 15 meters from the transceiver, and in a place where there are no obstacles between the device and the transceiver. 1. Mount the bracket securely to a surface which is more than 10 mm thick and can support more than 5 kg using the 4 supplied screws (5 × 20 mm). 2. Attach the device to the bracket. Mounting Example Spring washer Flat washer Specifications and options D Specifications General Operating temperature range 20°C ~ +60°C, 4ºF ~ +140ºF Power supply requirement Negative ground: 13.8 V DC nominal (10.8 ~ 15.9 V) Current drain (at 13.8 V) Dimensions (approximate) (projections not included) 3.5 A maximum 156.5 (W) × 67.6 (H) × 82.1 (D) mm, 6.2 (W) × 2.7 (H) × 3.2 (D) in Weight (approximate) 430 g, 15.2 oz Wireless LAN Wireless LAN standard IEEE802.11 b/g/n Authentication and Encryption WEP (64/128 bit), WPA-PSK (TKIP), WPA2-PSK (AES) Channels 1 to 13 (2.4 GHz band) LMay differ depending on the country of use. Output power Less than 10 mW/MHz Hailer Audio output power More than 25 W into a 4 load RX Hailer Audio output power More than 20 W into a 4 load 67.6 (2.7) Fuse replacement One fuse is installed in the supplied DC power cable. If the fuse blows or the device stops functioning, track down the source of the problem, repair it, and replace the damaged fuse with a new one of the proper rating. Fuse rating: 250 V 5 A 66.5 (2.6) D Dimensions 156.5 (6.2) 192.2 (7.6) 137 (5.4) 26 (1) 60.8 (2.4) Fuse Coding explanation Fuse Coding: F 250 V 5 A Fuse Voltage Rating: 250 Volts Fuse Current Rating: 5 Amperes 172.2 (6.8) 82.1 (3.2) 51 (2) Below statement is for UKCA purpose only United Kingdom Authorised Importer: Icom (UK) Ltd. Address: Blacksole House, Altira Park, Herne Bay, Kent, CT6 6GZ, U.K. 21.3 (0.8) 84.4 (3.3) D Options · SP-37 HORN SPEAKER 4 Unit: mm (inch) 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan Jul. 2022 A7626W-1EX-3 Printed in Japan © 20212022 Icom Inc. INSTRUCTIONS EXTERNAL INTERFACE BOX CT-M500 Thank you for choosing this Icom product. READ ALL INSTRUCTIONS carefully and completely before using this product. Important FCC information SAVE THESE INSTRUCTIONS-- These instructions contain important operating instructions for the CT-M500. This device connects to a transceiver through a Wireless LAN (WLAN) and expands the transceiver's functions. For the WLAN setting, the functions that you can operate when connecting to the transceiver, and so on, see the transceiver's manual for details. The transceiver's manual can be downloaded from the following internet address: https://www.icomjapan.com/support/ LThese instructions are described based on the CT-M500 firmware version 1.00. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Explicit definitions WORD DEFINITION CAUTION: Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this device under FCC regulations. R WARNING! Personal injury, may occur. fire hazard or electric shock CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. Définitions explicites TERME DÉFINITION R AVERTISSEMENT ! Risque de d'incendie blessures corporelles, ou de choc électrique. MISE EN GARDE Risque de dégât matériel. Inconvénient seulement, en cas de REMARQUE nonrespect. Absence de risque de blessures corporelles, d'incendie ou de choc électrique. Icom is not responsible for the destruction, damage to, or performance of any Icom or non-Icom equipment, if the malfunction is because of: · Force majeure, including, but not limited to, fires, earthquakes, storms, floods, lightning, other natural disasters, disturbances, riots, war, or radioactive contamination. · The use of Icom devices with any equipment that is not manufactured or approved by Icom. Information FCC Cet appareil est conforme à la partie 15 de la réglementation FCC. Son fonctionnement est soumis à la condition que cet appareil ne provoque pas d'interférences nocives. Cet équipement a été testé et reconnu conforme aux limites fixées pour un appareil numérique de classe B, conformément à la partie 15 de la réglementation FCC. Ces limites ont été fixées afin d'assurer une protection raisonnable contre les interférences nocives dans une installation résidentielle. Cet équipement génère, utilise et peut émettre un rayonnement de fréquence radio. S'il n'a pas été installé conformément aux instructions, il peut par ailleurs créer des interférences perturbant les communications radio. Toutefois, il n'y a aucune garantie que les interférences ne se produiront pas dans une installation particulière. Si cet équipement crée des interférences perturbant la réception de la radio ou de la télévision, comme cela peut être déterminé en éteignant et en allumant l'équipement, l'utilisateur est invité à essayer de corriger l'interférence en prenant une ou plusieurs des mesures ci-après : · Réorienter ou changer de place l'antenne de réception. · Éloigner l'équipement et le récepteur. · Connecter l'équipement sur une prise sur un autre circuit que celui sur lequel le récepteur est connecté. · Faire appel au revendeur ou à un technicien radio/TV expérimenté. MISE EN GARDE : Tout changement ou modification, non expressément approuvé par Icom Inc., peut annuler l'autorisation de l'utilisateur à utiliser cet appareil conformément à la réglementation FCC. Icom and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries. NMEA 2000 is a trademark of the National Maritime Electronics Association, Inc. All other products or brands are registered trademarks or trademarks of their respective holders. Recommendation CLEAN THE DEVICE THOROUGHLY WITH FRESH WATER after exposure to saltwater, and dry it before using. Otherwise, the device's keys may become unusable, due to salt crystallization. NOTE: If the device's waterproof protection appears defective, carefully clean it with a soft, damp (fresh water) cloth, then dry it before operating. The device may lose its waterproof protection if the case is cracked or broken, or the device has been dropped. Contact your Icom distributor or your dealer for advice. 1 About CE and DOC Hereby, Icom Inc. declares that the versions of CT-M500 which have the "CE" symbol on the product, comply with the essential requirements of the Radio Equipment Directive, 2014/53/EU, and the restriction of the use of certain hazardous substances in electrical and electronic equipment Directive, 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.icomjapan.com/support/ Disposal The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that in the European Union, all electrical and electronic products, batteries, and accumulators (rechargeable batteries) must be taken to designated collection locations at the end of their working life. Do not dispose of these products as unsorted municipal waste. Dispose of them according to the laws in your area. Precautions Précautions R WARNING! NEVER connect the device directly to an AC outlet. This may cause a fire or an electric shock. R WARNING! NEVER connect the device to a power source of more than 16 V DC such as a 24 V battery. This connection could cause a fire or damage the device. R WARNING! NEVER reverse the DC power cable polarity. This could cause a fire or damage the equipment. R WARNING! NEVER cut the DC power cable between the DC power connector and the fuse holder. If an incorrect connection is made after cutting, the device may be damaged. R WARNING! NEVER operate the device during a lightning storm. It may result in an electric shock, cause a fire or damage the device. Always disconnect the power source and other connectors before a storm. R WARNING! NEVER place the device where normal operation of the vessel may be hindered, or where it could cause bodily injury. CAUTION: DO NOT use or leave the device in areas with temperatures below 20°C ~ +60°C (4ºF ~ +140ºF), or in areas subject to direct sunlight, such as a dashboard. CAUTION: DO NOT use harsh solvents such as Benzine or alcohol when cleaning. This could damage the equipment surfaces. If the surface becomes dusty or dirty, wipe it clean with a soft, dry cloth. NEVER place the device in an insecure place to avoid inadvertent use by unauthorized persons. BE CAREFUL! The device's rear panel may become hot when continuously using for long periods of time. BE CAREFUL! The device meets IPX7 requirements for waterproof protection*. However, once the device has been dropped, or the waterproof seal is cracked or damaged, waterproof protection cannot be guaranteed because of possible damage to the case or the waterproof seal. * Except for the DC power connector and AF Out leads. NOTE: Install the device more than 1 meter from the vessel's magnetic navigation compass. NOTE: Install the device within approximately 15 meters from the transceiver or an existing access point, and in a place where there are no obstacles between the device and the transceiver. R AVERTISSEMENT ! NE JAMAIS relier l'appareil à une prise CA. Cela pourrait provoquer un choc électrique ou un incendie. R AVERTISSEMENT ! NE JAMAIS brancher l'appareil sur une source d'alimentation supérieure à 16 V CC, comme une batterie de 24 V. Cela pourrait endommager l'appareil. R AVERTISSEMENT ! NE JAMAIS inverser la polarité du câble d'alimentation CC lors de la connexion à une source d'alimentation. Cela pourrait endommager l'émetteur-récepteur. R AVERTISSEMENT ! NE JAMAIS couper le câble d'alimentation CC entre la prise CC et le porte-fusible. L'appareil peut être endommagé par la suite en cas de connexion inappropriée. R AVERTISSEMENT ! NE JAMAIS utiliser l'appareil durant un orage. Cela risquerait de provoquer un choc électrique, un incendie ou d'endommager l'appareil. Toujours débrancher la source d'alimentation et autre connecteurs avant une tempête. R AVERTISSEMENT ! NE JAMAIS installer l'appareil à un emplacement où il pourrait gêner le fonctionnement normal du navire ou provoquer des blessures corporelles. MISE EN GARDE : NE PAS utiliser ou placer l'appareil dans des zones où la temperature est inférieure à 20° ou supérieure à +60° ou dans des zones soumises au rayonnement solaire direct, telles le tableau de bord. MISE EN GARDE : NE PAS utiliser de dissolvants agressifs tels que du Benzène ou de l'alcool lors du nettoyage, car ils endommageraient les surfaces de l'appareil. Si l'appareil est poussiéreux ou sale, nettoyez-le avec un tissu doux et sec. NE placez JAMAIS l'appareil dans un endroit non sécurisé pour éviter toute utilisation par des personnes non autorisées. MISE EN GARDE : La face arrière de l'appareil chauffe en cas d'utilisation continue sur une longue durée. MISE EN GARDE : L'appareil est étanche conformément à la norme IPX7*. L'étanchéité ne peut plus être garantie après une chute de l'appareil en raison des risques de fissures du boîtier, de dégradation du joint d'étanchéité, etc. * Les connecteurs sur le panneau arrière ne sont pas étanche IPX7. REMARQUE : Installer l'appareil à au moins 1 m du compas de route du navire. REMARQUE : Installez l'appareil à environ 15 mètres de l'émetteurrécepteur ou d'un point d'accès existant et dans un endroit où il n'y a aucun obstacle entre l'appareil et l'émetteur-récepteur. Si l'appareil avant est exposé à de l'eau de mer, ASSUREZVOUS DE LE NETTOYER ENTIEREMENT AVEC DE L'EAU DOUCE lorsque la protection étanche sur l'appareil avant fonctionne. Dans le cas contraire, les touches risquent de ne plus fonctionner en raison de la cristallisation du sel. IC-M510 and CT-M500 RF Safety warning An internal Wireless LAN module and an antenna are supplied with the IC-M510 and CT-M500. To comply with FCC/ISED RF Exposure for the installed Wireless LAN unit, the device should be installed and operated with a minimum distance of 20 cm between the device and all persons. No other transmitting antenna is permitted to be located within 20 cm of the device. Avertissement de sécurité RF IC-M510 et CT-M500 Un module LAN sans fil interne et une antenne sont fournis avec l'IC-M510 et le CT-M500. Pour se conformer à l'exposition aux RF FCC / ISED pour l'unité LAN sans fil installée, l'appareil doit être installé et utilisé à une distance minimale de 20 cm entre l'appareil et toutes les personnes. Aucune autre antenne d'émission n'est autorisée à être située à moins de 20 cm de l'appareil. 2 Electromagnetic Interference When you use a Wireless LAN, pay attention to the following: Wireless LAN products operate in the 2.4 GHz band. The 2.4 GHz band is also used by other devices, such as Bluetooth devices, microwave ovens, RFID systems, amateur radio stations, and so on. When using this device near such devices, interference may occur, causing a decrease in communication speed, and an unstable connection. In such cases, use this device away from the other devices, or stop using those devices. Supplied accessories Mounting bracket DC power cable (OPC-2472) For the mounting bracket Screws (5 × 6 mm) Flat washers (M5) Screws (5 × 20 mm) Spring washers (M5) Panel description 5 6 12 43 D Front panel 1 STATUS INDICATOR Blinks green: Searching the transceiver. Lights green: Connecting to the transceiver. Lights red: Entering the WLAN Setup mode and waiting until the transceiver sets the WLAN setting. 2 POWER INDICATOR Lights blue when the device is turned ON. 3 POWER KEY [ ] Hold down for 1 second to turn the device ON or OFF. LThe device automatically connects to the transceiver. LIf the WLAN setting is not set, the device enters the WLAN Setup mode and waits until the transceiver sets the WLAN setting. 4 RESET KEY [RESET] Hold down [RESET] for 3 seconds when the device is turned ON to reset the WLAN setting. LThe Status indicator blinks red while holding down [RESET]. LThe device also restarts in the WLAN Setup mode and waits until the transceiver sets the WLAN setting. 8 7 D Rear panel 5 AF OUT LEADS Connects to an External Horn Speaker. Blue: External Horn Speaker (+) Gray: External Horn Speaker () Black, Orange: NC (Disconnected) NOTE: The connectors are attached to keep the leads together. Before connecting to a piece of equipment, cut the leads to remove the connector. 6 DC POWER CONNECTOR Connects to a 13.8 V DC power source. (+: Red, : Black) 7 NMEA 2000 CONNECTOR Connects to an NMEA 2000 network. 8 GROUND TERMINAL Connects to a vessel ground to prevent electrical shocks and interference from other equipment occurring. Use a PH M3 × 6 screw (user supplied). CAUTION: After connecting the DC power cable and AF Out leads, cover the connector and leads with an adhesive tape, as shown below, to prevent water seeping into the connection. Rubber vulcanizing tape 3