Waterproof Case Operation Manual

Introduction

Thank you for choosing this product! Please read the manual carefully before using the product. Keep the manual for reference. This manual takes the A1+FL2870 waterproof case set as the reference legend. Our company is only responsible for the defects of the waterproof case. We will not be responsible for any loss caused by improper use or force majeure.

Points for Attention

• When using the waterproof case for the first time or replacing the lens port or O-ring, please make sure to conduct the waterproof test of the empty case before loading the camera.
• Do not carry this product into the water from a high place, for the strong impact may cause the case to seep into water or damage the camera.
• If the temperature difference is large in a short time, the inner surface of the waterproof case may be dewed (small water drops). In case of condensation, please take out the camera from the diving shell and wipe off the water drops on the waterproof case and the camera with a soft dry cloth, and use it after the water vapor has completely evaporated.
• Do not damage the waterproof O-ring, or dust and dirt are accumulated between the waterproof O-ring and the waterproof case to avoid water leakage.
• Do not use the waterproof case in water whose temperature is lower than 0 °C and higher than 40 °C or more than 40 meters of water depth.
• In very hot and humid places, do not put the waterproof case in direct sunlight for a long time.
• In case of water seepage (the water leakage alarm lamp in the waterproof case flashes), stop using the waterproof case and water source immediately, and take out the camera to prevent the camera and waterproof case from failure.

Part Names

Part name (A1/A7RIV/A7RIVA/A9II)

• Data synchronization port
• Rear dial
• Mode dial
• Exposure compensation
• C2
• Cold shoe
• Shooting mode dial (A1/A911)
• C1
• Power on/off
• Shutter button
• Main dial
• MENU
• Electronic viewfinder
• MOVIE
• AF-ON/
• AEL/
• Multi-function selector
• Safety lock
• Control dial
• Display
• Fn
• C4/
• Playback
• Fiber-optic trigger interface
• 1/4 interface
• Lens port release button
• Vacuum system interface
• Focusing knob
• *No function (A7RIV/A7RIVA)

Part name (A7SIII)

• Data synchronization port
• Rear dial
• Cold shoe
• Exposure compensation
• C2
• MOVIE
• Power on/off
• Fiber-optic trigger interface
• Shutter button
• 1/4 interface
• Lens port release button
• Main dial
• Vacuum system interface
• Focusing knob
• MENU
• C3
• Electronic viewfinder
• AF-ON/
• AEL/
• Multi-function selector
• Safety lock
• Control dial
• Display
• Fn
• C4/
• Playback
• *No function

Installation of Lens Port

1. Select the required lens port and remove the body and dust cover of the lens port.
2. Check the groove and O-ring of the interface between the fuselage and lens port to ensure that there is no damage and debris attached. Take out the O-ring of the lens barrel and add a little waterproof silicone oil.
3. Align the lens port positioning point with the fuselage positioning point, push it in forcefully, and then turn the lens port clockwise until a click is heard.

Removal of lens port

Press and hold the lens port release button, turn the lens port counter-clockwise to release the lens port.

Open the waterproof case

This product is a clamshell structure. It is recommended to place the product on a flat surface.

1. Push down the red push button and keep it pressed.
2. Buckle part A outward.
3. Buckle part B outward.
4. After the left and right safety locks are opened, remove the back case and open it.

Component A: [Locking Mechanism Part A]

Component B: [Locking Mechanism Part B]

Waterproof test

General test

1. Open the waterproof case and check whether the O-ring is damaged or foreign matters are attached. If so, please clean it or replace it with a new O-ring.
2. Put in a dry paper towel, close and lock the waterproof case, and then immerse the waterproof case in water for about 15-20 minutes.
3. Take out the waterproof case and dry the case with a dry cloth.
4. Observe whether there is alarm flash in the waterproof case leakage alarm window.
5. Open the waterproof case to see if the tissue has changed.

Vacuum pump system test

If you buy the VP-100 series vacuum test system, you can use this device for quick waterproof test. Please refer to the manual of the vacuum test system for detailed steps.

VP-100 Vacuum detection system (Need to be purchased separately)

Preparation

1. Transfer your important photos and files from the camera to a computer.
2. Adjust the camera and configure the parameters suitable for underwater shooting.
3. Install a fully charged battery, insert the memory card, and ensure that there is enough space in the memory card for recording images.
4. Remove the wrist strap from the camera.
5. Install the appropriate lens (all types of filters or shields need to be removed).

Camera installation and use

1. Put the corresponding zoom gear into the camera lens (some lenses need to be disassembled and then inserted).
2. To use the data synchronization flash mode, you need to connect the built-in hot shoe plug of the waterproof case to the camera hot shoe. *Note 1
3. To use the fiber optic flash trigger mode, you need to install the SR-009 flash trigger to the camera hot shoe and turn on the power. *Note 2
4. Open the waterproof case, put the camera in carefully, and then close and lock the waterproof case.
5. Operate the buttons and dials on the waterproof case repeatedly to ensure that the camera functions normally.

*Note 1: For detailed steps, please refer to the manual of the data synchronization cable (sold separately).

*Note 2: For detailed steps, please refer to the flash trigger manual (sold separately).

Maintenance and maintenance

Please check the O-ring part of the main body of the waterproof case before launching. If the O-ring is stained with foreign matters, it can be taken out separately and cleaned with clean water, and then dried with a soft cloth without chips. After cleaning, the O-ring needs to add lubricating silicone oil. Refer to the following steps for operation:

1. Take out the O-ring with the attached O-ring disassembly piece.
2. Check whether there are foreign matters attached to the O-ring. If the O-ring is attached with debris, clean it with clean water. If the O-ring is damaged, please replace the O-ring immediately.
3. After cleaning, the O-ring needs to be re-lubricated with silicone oil. Take a clean plastic bag, put the O-ring to be lubricated, and then squeeze it in.
4. Pinch the plastic bag with your fingers to make the silicone oil evenly distributed to the O-ring.
5. Carefully check the flash O-ring groove. If there are any foreign matters in the groove, please use clean cotton-free soft cloth or special cotton swab with blowing balloon to remove, and then put the lubricated O-ring back into the groove.

Notice: Do not remove the O-ring by force or use sharp and hard metal objects, or the O-ring or waterproof groove may be damaged.

Maintenance precautions

• Please maintain in a dry and bright area.
• Only use original brand spare O-ring and silicone oil.
• When installing the O-ring back into the groove of the waterproof shell, pay attention to the smoothness of the O-ring and the groove without distortion.
• Check the O-ring and groove again after installation to ensure that there is no debris attached.
• In order to ensure the waterproof performance of the product, it is recommended to replace the main O-ring once a year.
• After using the waterproof shell for 1 year or 200 times, it is recommended to send the product back to the distributor or manufacturer for professional maintenance. (Note: there may be costs)

Storing

• After each diving, please take out the camera, close and lock the waterproof case, and soak it in fresh water for 15-30 minutes. During this period, operate all buttons and knobs several times to avoid salt residue accumulation. Lean and dry the waterproof case with a clean soft cloth.
• Store the waterproof case in a dry and ventilated environment without direct sunlight.
• Do not store in high temperature, cold and humid places, or near naphthalene chemicals or insecticides.
• If not using the waterproof case for a long time, it is recommended to remove the main O-ring and put it in a plastic bag for separate storage.

Specifications

Packaging list

Included:

• Camera waterproof case *1
• O-ring (back case) *1
• Spare O-ring (lens port) *1
• Spare O-ring (vacuum system port) *1
• Spare O-ring (vacuum system port cover) *1
• Cleaning cloth *1
• Instructions *1
• O-ring disassembly plate *1
• Hand rope *1
• Heck rope *1
• Anti-fog sheet *1
• Remover *1

Optional lens ports:

• FL2870 Assembly
• FL90 Assembly
• WA005 wide-angle series (6" Hemispherical lens)
• WA006 wide-angle series (8" Hemispherical lens)

Size/Weight:

• A1+FL2870 kit: Size: approx. 219*193*176mm, Weight: approx.1543g
• A1+FL90 kit: Size: approx. 242*193*176mm, Weight: approx.1618g
• A1+WA005-F kit: Size: approx. 312*212*223mm, Weight: approx.1764g

Function extension support

• ✔ All Camera Function
• ✔ Fiber Optic Cable Flash
• ✔ Sync Cable Flash
• ✔ Cold Shoe Interface
• ✔ 1/4 Mounting Plate
• Handheld Bracket
• Electronic Leak Detection Sensor
• Light Arms Extend
• ✔ Vacuum test
• Interchangeable Lenses Port
• Lenses Manual
• Zoom