Home & Kitchen Appliances | Sunbeam
Home & Kitchen Appliances | Sunbeam
User Manual for Sunbeam models including: HPM5000 Heating Pads, HPM5000, Heating Pads, Pads
User Manual for HPM5000
User Manual for HPM5100
User Manual for HPN5300
File Info : application/pdf, 6 Pages, 3.43MB
DocumentDocumentHeating Pads User Guide HPM5000, HPM5100, HPN5300 Contents Sunbeam's Safety Precautions 3 Get to know your Heat Pad 5 Using your heat pad 6 Care and cleaning 7 Storing the heat pad 8 Troubleshooting 8 Warranty Information 9 Important instructions - retain for future use. Sunbeam's Safety Precautions Sunbeam is very safety conscious when designing · Do not use an appliance for any purpose other and manufacturing consumer products, but it is than its intended use. essential that the product user also exercise care · Do not place an appliance on or near a hot gas when using an electrical appliance. Listed below are flame, electric element or on a heated oven. Do precautions which are essential for the safe use of not place on top of any other appliance. an electrical appliance: · Do not let the power cord of an appliance hang · Read carefully and save all the instructions over the edge of a table or bench top or touch provided with an appliance. any hot surface. · Always turn the power off at the power outlet · Do not operate any electrical appliance with before you insert or remove a plug. Remove by a damaged cord or after the appliance has grasping the plug - do not pull on the cord. been damaged in any manner. If damage · Turn the power off and remove the plug when is suspected, return the appliance to the the appliance is not in use and before cleaning. nearest Sunbeam Appointed Service Centre for · Do not use your appliance with an extension examination, repair or adjustment. cord unless this cord has been checked and · For additional protection, Sunbeam recommend tested by a qualified technician or service the use of a residual current device (RCD) person. with a tripping current not exceeding 30mA in · Always use your appliance from a power outlet of the electrical circuit supplying power to your the voltage (A.C. only) marked on the appliance. appliances. · Close supervision is necessary when your · Do not immerse the appliance in water or any appliance is being used by children or infirm other liquid unless recommended. persons. · Appliances are not intended to be operated by · Young children should be supervised to ensure means of an external timer or separate remote that they do not play with the appliance. control system. · Never leave an appliance unattended while in use. If you have any concerns regarding the performance and use of your appliance, please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line. Ensure the above safety precautions are understood. 3 Safety Precautions for your Heat Pad · Do not switch the heat pad on if moist or · Do not use if you have tuberculosis, tumours, wet. phlebitis, haemorrhages or thrombosis. · Do not use pins, needles, safety pins or other · Do not use if you have a pace maker fitted. sharp items on your heat pad. · Do not use outdoors. · Examine periodically for signs of wear or · Do not use when intending to sleep. damage on the heat pad cords. If there · Keep out of the reach of children. are such signs, or the heat pad has been misused, return it to an authorised service agent for inspection. · This heat pad is not intended for use in hospitals. · If appliance is used on an adjustable bed, · Only use your heat pad with the controls supplied or marked equivalent. check that the heat pad and cord do not become trapped or rucked, for example in · Not to be used by very young children (0-3 hinges. years), infirm persons, or persons insensitive · When storing the appliance allow it to cool to heat. down before folding. · Children under the age of three are not to · Do not crease the appliance by placing items use this appliance due their inability to react on top of it during storage. to overheating. · Should your appliance suffer a thermal or · The appliance is not to be used by young children over the age of three unless the controls have been pre-set by a parent or guardian, or unless the child has been fuse link rupture (normally identified when the heat pad stops heating) please return it to the manufacturer or agent for repair or replacement. adequately instructed on how to operate the controls safely. · Ensure that the heat pad is switched off and · This appliance must not be used by persons insensitive to heat and other very vulnerable persons who are unable to react to unplugged after use. overheating. · Do not use on varicose veins. · Do not use if folded or crumpled. · Do not use if you have skin disorders or open · Use only with the cover supplied. wounds. · Do not use the heat pad to heat animals. · Do not use on sensitive skin or areas insensitive to heat. · If you are pregnant or suffer from diabetes consult your health care practitioner before using. Important instructions - retain for future use. If you have any concerns regarding the performance and use of your appliance, please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line. Ensure the above safety precautions are understood. Care Label Symbols Attention Instruction Booklet - Please read the instructions thoroughly before use 4 Get to know your heating pad HPM5000 HPM5100 Temperature Setting Button Power Button HPN5300 Controller 1. Low - Up to 30 degrees 2. Mild - 31 to 33 degrees 3. Medium - 34 to 36 degrees 4. High - 37 to 39 degrees 5. Rapid heat up only Standby Indicator 5 Using your Heat Pad Using your Heat Pad · Remove all packaging · Ensure the power button on the controller is in the off position (not pressed in) · Connect the controller to the heat pad · Insert the plug into the power outlet and switch on · The heat pad will automatically default to setting 5 for rapid heating, and begin to heat up. · Setting 5 is for heat up only. Do not use this setting for continuous or overnight use. · Place the heat pad behind your back or neck whilst sitting or lying on a couch, chair or bed. This versatile heat pad is · a cozy and comfortable addition to any lounge or bedroom. · You can use the sleeve to secure the heat pad to a chair back or around your arm or leg. · To reduce the warmth, switch to a lower heat setting. For any continuous or overnight use, select from settings 1-4 only. Note: If the blue standby indicator light on the controller begins to flash, turn the controller off and check that the controller is properly connected to the heat pad. If the blue standby indicator continues to flash after turning the controller back on, contact your local Sunbeam Service Agent. Auto off function · The heat pad features an auto shut off. After 3 hours operation, the blue standby indicator light will show to indicate the heat pad has switched itself off. Care and Cleaning This Feel Perfect heat pad features waterproof heating elements, making them fully immersible and safe to wash by hand or machine. Before cleaning your heat pad, ensure that the controls are unplugged from the heat pad. Spot cleaning Sponge the affected area using a neutral wool detergent or mild soap flakes mixed with lukewarm water. Sponge twice with clean water to remove detergent. Remove excess water by compressing the wet area between two towels. Hand washing Wash the heat pad in lukewarm water with a neutral wool detergent or mild soap flakes. Soak for five minutes, then gently squeeze the soapy water through the fabric. Rinse thoroughly in clean, lukewarm water then drain excess water from the heat pad. Do not wring. Machine washing Take your heat pad to a commercial laundry or wash in a domestic washing machine. Wash on WOOL or DELICATES cycle with a neutral wool detergent or mild soap flakes, below 40°C. Do not use high speed or extra spin cycles. Line drying Drape the heat pad across several lines of your clothesline. Do not use pegs on the wired areas. Do not dry with a hairdryer or heater. Ensure that the heat pad and control sockets are completely dry before using again. Machine drying Tumble dry your heat pad on LOW setting for 15 minutes MAXIMUM. Smooth the heat pad by gently pulling any creases out of the fabric. Line dry to ensure the heat pad and control sockets are completely dry before use. Do not dry with a hairdryer or heater. Storing your heat pad Roll or fold your heat pad loosely and store in a blanket bag or the bag it was supplied in. Avoid pressing sharp creases into the heat pad. Do not place heavy items on top of your heat pad when storing. Checking your heat pad Examine the heat pad frequently for signs of wear or damage. If there are any such signs or if the heat pad has been misused, return it to your nearest Sunbeam Service Agent prior to any further use. 6 7 Storing The Heating Pad Store this appliance as follows when not used: · Wait for the heating pad to be completely dry if previously washed. · It is recommended to place the heating pad in the package provided upon purchase for better storage. · When storing the appliance, allow it to cool down before folding. · Store the heating pad in a dry place. Examine the appliance and its supply cord frequently for signs of wear or damage. lf there are such signs or in the case of malfunction, contact an authorised technical service centre. Troubleshooting This chapter describes the most common problems that can arise using the appliance. If the problems cannot be solved with the information below, please contact the Authorised Assistance Centre. Problem The LEDs on the control unit do not light up. The blue warning light is flashing. Temperature LED 1 (1) is flashing. The product has been used incorrectly or is damaged. The power cable or another internal wire is damaged. The control unit is damaged. There are holes or tears in the fabric or stubborn creases that do not spread out. Solution Check that the control unit plug is fully inserted in the socket. If the LEDs remain off, remove the control unit plug from the socket and return the underblanket to an authorised technical service centre. Turn the control unit off and remove the plug from the socket. Check that the control unit connector (6) is fully inserted in the heating pad connector (5) and reinsert the plug in the socket. If the standby LED continues to flash, return the heating pad to an authorised technical service centre. Return the heating pad to an authorised technical service centre to be checked. Year 2 year Australia www.sunbeam.com.au 1300 881 861 New Zealand www.sunbeam.co.nz 0800 786 232 2 years 8 9 Need help with your appliance? Contact our customer service team or visit our website for information and tips on getting the most from your appliance. Australia | visit phone New Zealand | visit phone www.sunbeam.com.au 1300 881 861 www.sunbeam.co.nz 0800 786 232 Newell Australia Pty Ltd. ABN 68 075 071 233 Sunbeam is a registered trade mark. Made in China to Sunbeam's specification. Due to minor changes in design or otherwise, the product you buy may differ slightly from the one shown here. Approved by the appropriate electrical regulatory authorities. ©Copyright Sunbeam 2021. GCDS-SUN-SL HPM5000_HPM5100_HPN5300_21EM1 (ANZ) P.N: NWL0001354562 SAP 2166995 SAP 2166996 SAP 2167009