User Guide for CP electronics models including: EBR-CPIR-DALI, EBR-CPIR-DALI Ceiling PIR Detector, Ceiling PIR Detector, PIR Detector, Detector
CP Electronics RAPID DALI2 Ceiling PIR IP20 detector | EBR-CPIR-DALI | CP ELECTRONICS
2 giorni fa — The DALI-2 RAPID PIR presence detectors provides automatic control of lighting. It is connected to the RAPID. DALI-2 Gateway via a DALI network.
3 days ago — For reference only: Devices (detectors / input units) and driver combinations for 200mA supply. This assumes that the sensor LEDs are all on, and the sensor is ...
File Info : application/pdf, 4 Pages, 1.03MB
DocumentDocumentProduct Guide EBR-CPIR-DALI DALI-2 network input device ceiling PIR Overview The DALI-2 RAPID PIR presence detectors provides automatic control of lighting. It is connected to the RAPID DALI-2 Gateway via a DALI network. Functioning as a presence detector, the unit can turn lights on when a room is occupied and off when the room is empty. An adjustable internal light sensor provides light level information to the RAPID system to allow lights to be kept off if sufficient daylight is present, and to enable maintained illuminance for dimming systems. An integral IR sensor in the unit allows the unit to be commissioned, and used in conjunction with a remote control handset (part no: UHS) to: · Act as a conventional dimmer · Override the unit on or off Front features Mounting Bezel Back features Pluggable screw terminals DALI - da DALI + da Sensor Lens which covers... PIR Sensor IR Receiver Light Level Sensor Status LED Features PIR Sensor Detects movement within the unit's detection range, allowing load control in response to changes in occupancy. IR Receiver Receives control and programming commands from an IR (infrared) handset. Light Level Sensor Measures the overall light level in the detection area Status LEDs The LED flashes Red or Green to indicate the following: Walk Test LED active Valid setting received when movement is detected DALI connection Connection to the DALI bus via pluggable screw terminals. The DALI bus is polarity insensitive. Installation Choosing a Suitable Location The EBR-CPIR-DALI are designed to be ceiling mounted and must satisfy the following criteria: · Avoid positioning the unit where direct sunlight may enter the sensor element. · Do not site the sensor within 1m of any lighting, forced air heating or ventilation. · Do not fix the sensor to an unstable or vibrating surface. · Do not exceed maximum length of cable (200m) on data bus. · Do not exceed maximum bus loading (240mA). Installation System wiring example (For reference) RAPID DALI gateway RAPID PIR RAPID Area Controller CAT 5 cable 3 core SELV RAPID Scene plates CAT 5 cable DALI bus Standard light switches EBR-BB-IN-DALI EBR-CPIR-DALI IMPORTANT NOTICE! This device should be installed by a qualified electrician in accordance with the latest edition of the IET Wiring Regulations and any applicable Building Regulations. 2 DALI-2 light fitting The EBR-CPIR-DALI are designed to be mounted using either: · Flush fixing, or · Surface fixing, using the optional Surface Mounting Box (part no. EBDBB). Both methods are illustrated below. Flush Fixing 1 Hole Ø64mm 2 3 Warning - be careful bending springs when mounting unit. Installation 4 Surface Fixing 1 2 50mm or 60mm fixing centres 3 4 Wire stripping details Pull out spring tab and rotate spring arm as shown Important Ensure that the cables are formed as shown before affixing the cable clamp. The clamp MUST clamp the outer sheath(s) only. Bend cores as shown. DALI bus loading For reference only: Devices (detectors / input units) and driver combinations for 200mA supply. This assumes that the sensor LEDs are all on, and the sensor is receiving IR communication. · 4 devices and up to 64 drivers · 5 devices and up to 55 drivers · 6 devices and up to 44 drivers · 7 devices and up to 33 drivers · 8 devices and up to 22 drivers · 9 devices and up to 12 drivers · 10 devices and up to 2 drivers In most realistic scenarios, only one LED is on at a time and only one detector is receiving IR; guidance changes to. · 10 devices up to 64 drivers · 11 devices up to 60 drivers · 12 devices up to 55 drivers · 13 devices up to 50 drivers · 14 devices up to 48 drivers · 15 devices up to 44 drivers Addressing limits of DG64 · 5 input units of 7 channels each · 10 detectors 3 Technical data Dimensions: See diagrams opposite Weight: 0.15kg Supply Voltage: 9.5V--22.5VDC over DALI Bus Nominal Current Consumption: 8mA Maximum (Peak) Current Consumption: 18mA DALI bus: Cannot be considered as SELV since DALI, ballasts only offer basic insulation, therefore all devices on the DALI bus must be wired as Terminal Capacity: if carrying mains potential. 2.5mm2 Temperature: -10ºC to 35ºC Humidity: 5 to 95% non-condensing Material (casing): Flame retardant ABS and PC/ABS Type: Class 2 IP rating: IP40 Compliance: CE & UKCA DALI-2 Certification IEC62386 Parts 101,103, 303 & 304 For further compliance information visit www.legrand.co.uk EBR-CPIR-DALI EBDBB - Surface mounting box Detection diagram EBR-CPIR-DALI Part numbers RAPID Detector Accessories Part number EBR-CPIR-DALI EBDBB UHS UNLCDHS Description DALI-2 network, input device, ceiling PIR presence detector Surface mounting box User handset override on/off; lux up/lux down Universal LCD programming handset Due to our policy of continual product improvement CP Electronics reserves the right to alter the specification of this product without prior notice. 4 CP Electronics a brand of Legrand Electric Limited Brent Crescent London NW10 7XR United Kingdom Tel: + 44 (0) 333 900 0671 E-mail: customerservice.cpelectronics@legrand.com Website: www.legrand.co.uk/en/brands/cp-electronics Ref: #WDA089 Issue 1