Compliance proofs for products: LANCOM Systems GmbH
User Guide for LANCOM models including: GS-3152P Fully Managed Access Switches, GS-3152P, Fully Managed Access Switches
prieš 6 dienas — Hardware. Power supply. Internal power supply unit (110–230 V, 50–60 Hz, max. 1 A). Power consumption. Max. 470 W. Environment. Temperature range 0–40° C; ...
Lancom GS-3152 Rackmount Gigabit Managed Switch, 48x RJ-45, 4x SFP | Preisvergleich Geizhals Österreich
File Info : application/pdf, 1 Pages, 347.40KB
DocumentDocumentMOUNTING AND CONNECTING THE DEVICE LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and / or omissions. 111674/0122 TECHNICAL DATA LANCOM GS-3152P Quick Reference Guide a b c d a Configuration interface (Console) Connect the configuration interface via the included serial configuration cable to the serial interface of the device you want to use for configuring / monitoring the switch. b TP Ethernet interfaces 10M / 100M / 1G PoE+ Use Ethernet cables to connect the interfaces 1 to 36 to your PC or a LAN switch. c TP Ethernet interfaces 10M / 100M 1G Use Ethernet cables to connect the interfaces 37 to 48 to your PC or a LAN switch. d SFP interfaces 1G Insert suitable LANCOM SFP modules into the SFP interfaces 49 to 52. Choose cables which are compatible with the SFP modules and connect them as described in the module's documentation. e Power connector (device back side) E Supply power to the device via the power connector. Please use the IEC power cable supplied or a country-specific LANCOM Power Cord. ab c c d a System / Link/Act/Speed / PoE LED System: off Device powered off System: green Device operational System: red Hardware error Link/Act/Speed: green Port LEDs show link / activity / port speed status PoE: green Port LEDs show PoE status b Mode/Reset button Pressed until all port Device restart LEDs are off Pressed until all port Configuration reset and device restart LEDs glow permanently c TP Ethernet ports Off Port inactive or disabled Green Link 1000 Mbps Green, blinking Data transfer, link 1000 Mbps Orange Link 100 Mbps Orange, blinking Data transfer, link 100 Mbps d 1 G SFP ports Off Port inactive or disabled Green Link 1 Gbps Green, blinking Data transfer, link 1 Gbps Hardware Power supply Power consumption Environment Housing Number of fans Internal power supply unit (110230 V, 5060 Hz, max. 1 A) Max. 470 W Temperature range 040° C; short term temperature conditions 0-50°C; humidity 1090%; non-condensing Robust metal housing, 1 HU with removable mounting brackets for 19" installation, network connectors on the front, 442 x 44 x 375 mm (W x H x D) 1 Interfaces ETH SFP A 48 TP Ethernet ports 10 / 100 / 1000 Mbps, including 36 PoE+ ports A 4 SFP ports 1 Gbps A 52 concurrent ports in total Declaration of Conformity Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc Package Content Manual Mounting brackets Cable Quick Reference Guide (DE/EN), Installation Guide (DE/EN) Two 19" brackets for rack mounting; If an additional rear support surface is required for more stable mounting of the switch, please use the LANCOM Switch Rack Mount L250, item no.: 61432, which is available as an accessory. IEC power cord 230 V, serial configuration cable 1.5 m Cloud-ready 4 Please observe the following when setting up the device A The mains plug of the device must be freely accessible. A For devices to be operated on the desktop, please attach the adhesive rubber footpads. A Do not rest any objects on top of the device and do not stack multiple devices. A Keep all ventilation slots of the device clear of obstruction. A Mount the device into a 19" unit in a server cabinet using the provided screws and mounting brackets. If an additional rear support surface is required for more stable mounting of the switch, please use the LANCOM Switch Rack Mount L250. A Please note that support for third-party accessories (SFP and DAC) is not provided. Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide! Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.