Falcon Door Controls
The Falcon Difference
At Falcon, products are designed to meet local building codes and high expectations for performance and quality. Falcon door closers deliver durability, convenience, and unmatched value, built on standards of providing quality products at a reasonable price, delivered on time. This makes Falcon door closers a powerful choice for any project.
SC70A Series
Falcon SC70A Series heavy-duty closers are built for applications demanding reliable door control and easy maintenance. They are ANSI grade 1, ADA compliant, and deliver tough performance. Suitable for interior or exterior doors in retail shops, restaurants, small offices, and other high-traffic applications.
Standard Features
- Fully adjustable sizes 1-6
- Separate adjustable general speed, latch speed, and backcheck
- Mounts: hinge side, top jamb, or parallel arm (when RW/PA or HW/PA arm is specified)
- Non-handed for left or right swinging doors
- 1 1/2" diameter heat-treated steel piston
- Double heat-treated pinion
- Universal screw pack for aluminum, hollow metal, and wood doors (includes self-reaming and tapping screws)
- Staked valves
- Meets ANSI A117.1
- Listed ANSI/BHMA A156.4, grade 1
- UL listed and compliant to UL10C and UBC 7-2 (1997)
- Fast and easy installation
- 10-year warranty
- Available finishes: aluminum, brass, dark bronze, and matte black
Listings and Ratings
The Falcon SC71A is UL approved and compliant with UL 10C and UBC 7-2 (1997) fire tests. It is rated ANSI/BHMA A156.4, grade 1, and designed to meet the American Disabilities Act (ADA) and ANSI A117.1.
Installation Dimensions
Hinge (Pull Side)
For hinge side mounting (pull side), door opening angles and corresponding frame/door clearances are provided:
- Up to 100°: 13" (330mm)
- 101° to 120°: 12" (305mm)
- 121° to 150°: 10" (254mm)
- 151° to 180°: 9 1/2" (241mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
- Reveal should not exceed 3/4" (19mm) for regular arm or hold-open arm.
- Clearance of 2 1/8" (54mm) behind the door is required for 90° installation.
- Top rail less than 3 7/8" (98mm) requires plate SC70A-18.
- Delayed action is available by adding suffix "DEL" to the cylinder, delaying closing from maximum opening to approximately 70°.
Top Jamb (Push Side)
For top jamb mounting (push side), door opening angles and corresponding frame/door clearances are provided:
- Up to 100°: 13" (330mm)
- 101° to 120°: 12" (305mm)
- 121° to 150°: 10" (254mm)
- 151° to 180°: 9 1/2" (241mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
- Reveal should not exceed 3 1/4" (83mm) for regular arm or hold-open arm.
- A top rail of 1 1/2" (38mm) is required.
- Head frame less than 3 7/8" (98mm) requires plate SC70A-18.
- Delayed action is available by adding suffix "DEL" to the cylinder, delaying closing from maximum opening to approximately 70°.
Parallel (Push Side)
For parallel arm mounting (push side), door opening angles and corresponding frame/door clearances are provided:
- Up to 100°: 8 15/16" (227mm)
- 101° to 130°: 7 7/16" (189mm)
- 131° to 150°: 6 7/16" (164mm)
- 151° to 180°: 5 7/16" (138mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
- Top rail less than 6" (152mm) measured from the stop requires plate SC70A-18PA.
- Delayed action is available by adding suffix "DEL" to the cylinder, delaying closing from maximum opening to approximately 70°.
Heavy Duty (Parallel)
For heavy-duty parallel arm mounting, door opening angles and corresponding frame/door clearances are provided:
- Up to 100°: 8 7/8" (225mm)
- 101° to 130°: 7 3/8" (187mm)
- 131° to 150°: 6 3/8" (162mm)
- 151° to 180°: 5 3/8" (137mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point, where a door cannot swing 180°, or where a dead stop or spring-n-stop arm is not used.
- Top rail less than 6" (152mm) measured from the stop requires plate SC70A-18PA.
- Delayed action is available by adding suffix "DEL" to the cylinder, delaying closing from maximum opening to approximately 70°.
Dead Stop HO (Parallel)
For dead stop hold-open parallel arm mounting, door opening angles and corresponding frame/door clearances are provided:
- 85°: 10 5/8" (270mm)
- 90°: 9 3/4" (248mm)
- 95°: 9 1/8" (232mm)
- 100°: 8 3/8" (213mm)
- 105°: 7 7/8" (200mm)
- 110°: 7 1/4" (138mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Top rail less than 6" (152mm) measured from the stop requires plate SC70A-18PA.
- Delayed action is available by adding suffix "DEL" to the cylinder, delaying closing from maximum opening to approximately 70°.
Arm Types
All SC70A Series closers come with a full cover, standard arm, and screw pack.
- Regular arm, SC70A-3077PA: Non-handed arm with adjustable forearm assembly for various door and frame reveal conditions. Mounts hinge side, top jamb, or parallel arm. PA shoe included for parallel arm configuration.
- Hold-open arm, SC70A-3049PA: Optional, non-handed, hold-open arm with adjustable forearm assembly. Mounts hinge side, top jamb, or parallel arm. PA shoe included for parallel arm configuration.
- Heavy duty regular arm, SC70A-3077HD: Optional, non-handed, stamped, heavy-duty, parallel arm for high-traffic applications.
- Dead stop arm, SC70A-3077DS: Optional, non-handed, stamped, heavy-duty, parallel arm with a positive mechanical stop and non-adjustable forearm assembly for high-volume or potentially abusive installations.
- Dead stop hold-open arm, SC70A-3049DS: Optional, non-handed, stamped, heavy-duty, hold-open parallel arm with a positive mechanical stop and non-adjustable forearm assembly. Includes a manually selective hold-open function.
- Spring-n-stop arm, SC70A-3077SS: Optional, non-handed, extra heavy-duty, forged parallel arm with an integral spring stop and non-adjustable forearm assembly for high-volume or potentially abusive installations.
- Spring-n-stop hold-open arm, SC70A-3049SS: Optional, non-handed, extra heavy-duty, forged parallel arm with an integral spring stop and non-adjustable forearm assembly. Includes a manually selective hold-open function.
- Forged arm, SC70A-3077FA: Optional, non-handed, extra heavy-duty arm with parallel arm bracket. Includes a forged steel main arm and forearm for maximum durability in high-traffic and/or abusive applications. Parallel Arm (PA) bracket is a permanent feature, installation on "push" side of the door in a parallel arm configuration is required.
- Forged arm with hold open, SC70A-3049FA: Optional, left or right handed, extra heavy-duty arm with parallel arm bracket incorporating a hold-open feature. Includes a forged steel main arm and forearm for maximum durability. Parallel Arm (PA) bracket is a permanent feature, installation on "push" side of the door in a parallel arm configuration is required.
Installation Accessories
- Soffit shoe support, SC70A-30: Provides anchorage for the fifth screw used with a soffit shoe, where reveal is less than 3 1/16" (78mm).
- Blade stop spacer, SC70A-61: Required to lower the parallel arm shoe to clear a 1/2" (13mm) blade stop.
- Auxiliary shoe, SC70A-62A: Requires a top rail of 7" (178mm). Optional shoe replaces the PA shoe for parallel arm mounting of a regular arm with an overhead holder/stop.
- Cover, SC70A-72: Standard, non-handed, full plastic cover encloses the closer body.
- Plate, SC70A-18: Required for hinge side mount where top rail is less than 3 7/8" (98mm). Required for top jamb mounting where head frame is less than 3 7/8" (98mm).
- Plate, SC70A-18PA: Required for parallel arm mounting where top rail is less than 6" (152 mm), measured from the stop. Plate requires 1 3/4" (44mm) minimum top rail measured from the stop.
SC80A Series
The Falcon SC80A Series offers medium-duty performance for applications like retail storefronts, cafes, and clinics, ensuring smooth and secure door operation. It provides ANSI grade 1 durability and reliable performance for interior and exterior doors, with an adjustable design for flexible installation and ADA compliance.
Standard Features
- Single piece cast aluminum body
- Fully adjustable sizes 1-6
- Separate adjustable general speed, latch speed, and backcheck
- Mounts: hinge side, top jamb, or parallel arm (when RW/PA or HW/PA arm is specified)
- Non-handed for left or right swinging doors
- 1 1/4" diameter heat-treated steel piston
- Heat-treated pinion
- Universal screw pack for aluminum, hollow metal, and wood doors (includes self-reaming and tapping screws)
- Staked valves
- Meets ANSI A117.1
- ANSI/BHMA A156.4, grade 1
- UL listed and compliant to UL10C and UBC 7-2 (1997)
- Cover is UL approved for use in fire rated assemblies
- 10-year warranty
- Retrofittable to Norton 8000 hole pattern
Listings and Ratings
The Falcon SC81A is UL listed and compliant to UL10C and UBC 7-2 (1997). It is designed to meet the American Disabilities Act (ADA) and ANSI A117.1. The SC81A is rated ANSI/BHMA A156.4, Grade 1.
Installation Dimensions
Hinge (Pull Side)
For hinge side mounting (pull side), door opening angles and corresponding frame/door clearances are provided:
- Up to 120°: 11 3/4" (298mm)
- 121° to 180°: 8 1/2" (216mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
- Reveal should not exceed 3/4" (19mm) for regular arm or hold-open arm.
- Clearance of 2 3/8" (60mm) behind the door is required for 90° installation.
- Delayed action is available by adding suffix "DEL" to the cylinder, delaying closing from maximum opening to approximately 70°.
Top Jamb (Push Side)
For top jamb mounting (push side), door opening angles and corresponding frame/door clearances are provided:
- Up to 120°: 11 1/2" (292mm)
- 121° to 180°: 8 1/2" (216mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
- Reveal should not exceed 3 1/4" (83mm) for regular arm or hold-open arm.
- Head frame less than 2 5/16" (59mm) requires plate SC80A-18.
- Delayed action is available by adding suffix "DEL" to the cylinder, delaying closing from maximum opening to approximately 70°.
Parallel (Push Side)
For parallel arm mounting (push side), door opening angles and corresponding frame/door clearances are provided:
- Up to 120°: 3 3/4" (95mm)
- 121° to 180°: 2 1/16" (52mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
- Top rail less than 4 3/8" (111mm) measured from the stop requires plate SC80A-18PA.
- Delayed action is available by adding suffix "DEL" to the cylinder, delaying closing from maximum opening to approximately 70°.
Heavy Duty (Parallel)
For heavy-duty parallel arm mounting, door opening angles and corresponding frame/door clearances are provided:
- Up to 120°: 8 3/4" (222mm)
- 121° to 180°: 6 3/4" (171mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point, where a door cannot swing 180°, or where Dead stop or Spring-n-stop arm is not used.
- Top rail less than 4 3/8" (111mm) measured from the stop requires plate SC80A-18PA.
- Delayed action is available by adding suffix "DEL" to the cylinder, delaying closing from maximum opening to approximately 70°.
Dead Stop HO (Parallel)
For dead stop hold-open parallel arm mounting, door opening angles and corresponding frame/door clearances are provided:
- Up to 90°: 10 1/8" (257mm)
- 91° to 110°: 7 5/8" (194mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Top rail less than 4 3/8" (111mm) measured from the stop requires plate SC80A-18PA.
- Delayed action is available by adding suffix "DEL" to the cylinder, delaying closing from maximum opening to approximately 70°.
Arm Types
All SC80A Series closers come with a slim cover, standard arm, and screw pack.
- Regular arm, SC80A-3077PA: Non-handed arm with adjustable forearm assembly for various door and frame reveal conditions. Mounts hinge side, top jamb, or parallel arm. PA shoe included for parallel arm configuration.
- Hold-open regular arm, SC80A-3049PA: Optional, non-handed, hold-open arm with adjustable forearm assembly. Mounts hinge side, top jamb, or parallel arm. PA shoe included for parallel arm configuration.
- Heavy duty arm, SC80A-3077HD: Optional, non-handed, stamped, heavy-duty, parallel arm for high-traffic applications.
- Dead stop arm, SC80A-3077DS: Optional, non-handed, stamped, heavy-duty, parallel arm with a positive mechanical stop and non-adjustable forearm assembly for high-volume or potentially abusive installations.
- Dead stop hold-open Arm, SC80A-3049DS: Optional, non-handed, stamped, heavy-duty, hold-open parallel arm with a positive mechanical stop and non-adjustable forearm assembly. Includes a manually selective hold-open function.
- Spring-n-stop arm, SC80A-3077SS: Optional, non-handed, extra heavy-duty, forged parallel arm with an integral spring stop and non-adjustable forearm assembly for high-volume or potentially abusive installations.
- Spring-n-stop hold-open arm, SC80A-3049SS: Optional, non-handed, extra heavy-duty, forged parallel arm with an integral spring stop and non-adjustable forearm assembly. Includes a manually selective hold-open function.
Installation Accessories
- Soffit shoe support, SC80A-30: Provides anchorage for the fifth screw used with a soffit shoe, where reveal is less than 3 1/16" (78mm).
- Blade stop spacer, SC80A-61: Required to lower the parallel arm shoe to clear a 1/2" (13mm) blade stop.
- Auxiliary shoe, SC80A-62A: Requires a top rail of 7" (178mm). Optional shoe replaces the PA shoe for parallel arm mounting of a regular arm with an overhead holder/stop.
- Plate, SC80A-18: Required for top jamb mounting where head frame is less than 1 3/4" (44mm) or flush ceiling conditions exist.
- Plate, SC80A-18FC: Required for top jamb mounting where head frame is less than 1 3/4" (44mm) or flush ceiling conditions exist. To be used with a full cover SC80A-72FC.
- Plate, SC80A-18PA: Required for parallel arm mounting where top rail is less than 4 3/8" (111 mm), measured from the stop. Plate requires 1 7/8" (48mm) minimum top rail measured from the stop.
- Plate, SC80A-18PAFC: Required for parallel arm mounting where top rail is less than 4 3/8" (111mm), measured from the stop. Plate requires 1 7/8" (48mm) minimum top rail measured from the stop. To be used with a full cover SC80A-72FC.
- Cover, SC80A-72: Standard, non-handed, slim line plastic cover encloses the closer body with a cap on the unused pinion shaft.
- Cover, SC80A-72FC: Optional non-handed, full plastic cover encloses the closer body.
SC60A Series
The Falcon SC60A Series offers dependable performance for standard-duty applications, designed for interior use with aluminum storefronts. It provides ANSI grade 1 durability backed by a ten-year warranty and features the most common hole pattern in the industry for versatile use and easy retrofit.
Standard Features
- Single piece cast aluminum body
- Fully adjustable sizes 1-5
- Separate adjustable general speed, latch speed, and backcheck
- Mounts: hinge side, top jamb, or parallel arm (when RW/PA or HW/PA arm is specified)
- Non-handed for left or right swinging doors
- Heat-treated pinion and steel piston
- Universal screw pack for aluminum, hollow metal, and wood doors (includes self-reaming and tapping screws)
- Staked valves
- Meets ANSI A117.1
- ANSI/BHMA A156.4, grade 1
- UL listed and compliant to UL10C and UBC 7-2 (1997)
- Cover is UL approved for fire rated assemblies
- 10-year warranty
- Retrofittable to Norton 1600 hole pattern
Listings and Ratings
The Falcon SC60A is UL listed and compliant to UL10C and UBC 7-2 (1997). The SC61A is designed to meet the American Disabilities Act (ADA) and ANSI A117.1. The SC60A Series is rated ANSI/BHMA A156.4, Grade 1.
Installation Dimensions
Hinge (Pull Side)
For hinge side mounting (pull side), door opening angles and corresponding frame/door clearances are provided:
- Up to 120°: 11 13/16" (300mm)
- 121° to 180°: 8 1/4" (210mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
- Reveal should not exceed 3/4" (19mm) for regular arm or hold-open arm.
- Clearance of 2 3/4" (70mm) behind the door is required for 90° installation.
Top Jamb (Push Side)
For top jamb mounting (push side), door opening angles and corresponding frame/door clearances are provided:
- Up to 120°: 11 1/4" (286mm)
- 121° to 180°: 9 1/4" (235mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
- Reveal should not exceed 3 1/4" (83mm) for regular arm or hold-open arm.
- Head frame less than 1 3/4" (44mm) requires SC60A-18 plate.
Parallel (Push Side)
For parallel arm mounting (push side), door opening angles and corresponding frame/door clearances are provided:
- Up to 120°: 8 5/16" (211mm)
- 121° to 180°: 6 13/16" (173mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
- Top rail less than 4 3/8" (111mm) measured from the stop requires plate SC60A-18PA.
Heavy Duty (Parallel)
For heavy-duty parallel arm mounting, door opening angles and corresponding frame/door clearances are provided:
- Up to 100°: 7 11/16" (195mm)
- 101° to 180°: 3 11/16" (94mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point, where a door cannot swing 180°, or where Dead stop or Spring-n-stop arm is not used.
- Top Rail less than 4 1/4" (108mm) measured from the stop requires plate SC60A-18PA.
Dead Stop HO (Parallel)
For dead stop hold-open parallel arm mounting, door opening angles and corresponding frame/door clearances are provided:
- Up to 90°: 8 7/16" (214mm)
- 91° to 100°: 5 15/16" (151mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Top rail less than 4 1/4" (108mm) measured from the stop requires plate SC60A-18PA.
Arm Types
All SC60A Series closers come with a standard arm and screw pack.
- Regular arm, SC60A-3077PA: Non-handed arm with adjustable forearm assembly for various door and frame reveal conditions. Mounts hinge side, top jamb, or parallel arm. PA shoe included for parallel arm configuration.
- Hold-open arm, SC60A-3049PA: Optional, non-handed, hold-open arm with adjustable forearm assembly. Mounts hinge side, top jamb, or parallel arm. PA shoe included for parallel arm configuration.
- Heavy duty regular arm, SC60A-3077HD: Optional, non-handed, stamped, heavy-duty, parallel arm for high-traffic applications.
- Dead stop arm, SC60A-3077DS: Optional, non-handed, stamped, heavy-duty, parallel arm with a positive mechanical stop and non-adjustable forearm assembly for high-volume or potentially abusive installations.
- Dead stop hold-open arm, SC60A-3049DS: Optional, non-handed, stamped, heavy-duty, hold-open parallel arm with a positive mechanical stop and non-adjustable forearm assembly. Includes a manually selective hold-open function.
- Spring-n-stop arm, SC60A-3077SS: Optional, non-handed, extra heavy-duty, forged parallel arm with an integral spring stop and non-adjustable forearm assembly for high-volume or potentially abusive installations.
- Spring-n-stop hold-open arm, SC60A-3049SS: Optional, non-handed, extra heavy-duty, forged parallel arm with an integral spring stop and non-adjustable forearm assembly. Includes a manually selective hold-open function.
Installation Accessories
- Soffit shoe support, SC60A-30: Provides anchorage for the fifth screw used with a soffit shoe, where reveal is less than 3 1/16" (78mm).
- Blade stop spacer, SC60A-61: Required to lower the parallel arm shoe to clear a 1/2" (13mm) blade stop.
- Auxiliary shoe, SC60A-62A: Requires a top rail of 7" (178mm). Optional shoe replaces the PA shoe for parallel arm mounting of a regular arm with an overhead holder/stop.
- Plate, SC60A-18: Required for top jamb mounting where head frame is less than 1 3/4" (44mm).
- Plate, SC60A-18PA: Required for parallel arm mounting where top rail is less than 4 3/8" (111mm) for PA, 4 1/4" (108mm) for HD and DS, measured from the stop. Plate requires 2 3/8" (60mm) minimum top rail measured from the stop.
- Cover, SC60A-72: Optional, non-handed, slim line plastic cover. Designed for SC60A series.
SC90A Series
The Falcon SC90A Series offers smooth, reliable operation for light-duty interior applications, backed by a 10-year warranty and preset for easy installation. The SC93A/94A models are UL listed and compliant with UL 10C and UBC 7-2 (1997).
Standard Features
- Single piece cast aluminum body
- Fixed sizes 1, 3, and 4
- Separate adjustable general speed and latch speed
- Mounts: hinge side, top jamb, or parallel arm (when RW/PA arm is specified)
- Non-handed for left or right swinging doors
- Heat-treated pinion and steel piston
- SC93A/94A comes standard with a universal screw pack for aluminum, hollow metal, and wood doors (includes self-reaming and tapping screws)
- Meets ANSI A117.1
- Listed ANSI/BHMA A156.4, grade 3
- Comes standard with adjustable backcheck
- Available finishes: aluminum and dark bronze
Listings and Ratings
The Falcon SC93A/94A Series is UL approved and compliant with the UL 10C and UBC 7-2 (1997) fire test. The SC91A closers are designed to meet the American Disabilities Act (ADA) and ANSI A117.1. The SC90A Series is listed ANSI/BHMA A156.4, Grade 3.
Installation Dimensions
SC91A Hinge (Pull Side)
For SC91A hinge side mounting (pull side), door opening angles and corresponding frame/door clearances are provided:
- Up to 105°: 10 5/8" (270mm)
- 106° to 180°: 7 5/8" (194mm)
Additional requirements:
- Butt Hinges should not exceed 5" (127mm) in width.
- Auxiliary Stop is recommended at hold-open point or where a door cannot swing 180°.
- Reveal should not exceed 3/4" (19mm) for regular arm.
- Clearance of 2 1/2" (64mm) behind the door is required for 90° installation.
SC91A Top Jamb (Push Side)
For SC91A top jamb mounting (push side), door opening angles and corresponding frame/door clearances are provided:
- Up to 105°: 9 7/8" (251mm)
- 106° to 180°: 7 1/4" (184mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
- Reveal should not exceed 2" (51mm) for regular arm or hold-open arm.
- Note: Top jamb mount is only available with the regular arm.
SC91A Parallel (Push Side)
For SC91A parallel arm mounting (push side), door opening angles and corresponding frame/door clearances are provided:
- Up to 105°: 6 11/16" (170mm)
- 106° to 180°: 4 11/16" (119mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
SC93A/94A Hinge (Pull Side)
For SC93A/94A hinge side mounting (pull side), door opening angles and corresponding frame/door clearances are provided:
- Up to 120°: 11 3/4" (298mm)
- 121° to 180°: 9" (229mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
- Reveal should not exceed 3/4" (19mm) for regular arm.
- Clearance of 3" (76mm) behind the door is required for 90° installation.
SC93A/94A Top Jamb (Push Side)
For SC93A/94A top jamb mounting (push side), door opening angles and corresponding frame/door clearances are provided:
- Up to 120°: 11 1/2" (292mm)
- 121° to 180°: 8 1/2" (216mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
- Reveal should not exceed 3 1/4" (83mm) for regular arm.
SC93A/94A Parallel (Push Side)
For SC93A/94A parallel arm mounting (push side), door opening angles and corresponding frame/door clearances are provided:
- Up to 120°: 9 3/8" (238mm)
- 121° to 180°: 7 1/2" (191mm)
Additional requirements:
- Butt hinges should not exceed 5" (127mm) in width.
- Auxiliary stop is recommended at hold-open point or where a door cannot swing 180°.
- Backcheck closer with the backcheck option requires 105° mounting.
Arm Types and Accessories
All SC91A closers come with a standard arm. Optional pinion caps are also available for replacement. SC93A/94A closers come with a standard arm and screw pack. Optional accessories available for order.
- Regular arm, SC91A-3077PA: Non-handed arm with adjustable forearm assembly for various door and frame reveal conditions. Mounts hinge side, top jamb, or parallel arm. PA shoe included for parallel arm configuration. Available only on SC91A closers.
- Hold-open arm, SC91A-3049PA: Optional, non-handed, hold-open arm with adjustable forearm assembly. Mounts hinge side, top jamb, or parallel arm. PA shoe included for parallel arm configuration. Available only on SC91A closers.
- Pinion cap, SC91A: Available for replacement with SC91A.
- Regular arm, SC90A-3077PA: Non-handed arm with adjustable forearm assembly for various door and frame reveal conditions. Mounts hinge side, top jamb, or parallel arm. PA shoe included for parallel arm configuration. Available with SC93A/94A only.
- Soffit shoe support, SC90A-30: Provides anchorage for the fifth screw used with a soffit shoe, where reveal is less than 3 1/16" (78mm).
- Blade stop spacer, SC90A-61: Required to lower the parallel arm shoe to clear a 1/2" (13mm) blade stop.
- Auxiliary shoe, SC90A-62A: Requires a top rail of 7" (178mm). Optional shoe replaces the PA shoe for parallel arm mounting of a regular arm with an overhead holder/stop.
- Slim cover, SC90A-72: Optional non-handed, slim plastic cover. Available only with SC93A.
- Plate, SC90A-18: Required for top jamb mounting where head frame is less than 1 3/4" (44mm) or flush ceiling conditions exist. Available only with SC93A/94A.
- Plate, SC90A-18PA: Required for parallel arm mounting where top rail is less than 4 5/8" (117 mm), measured from the stop. Plate requires 2 1/8" (54mm) minimum top rail measured from the stop. Available only with SC93A/94A.
- Pinion cap, SC90A: Available for replacement with SC93A/94A.
OHC100A Series
Overhead concealed closers provide door opening and closing control with an aesthetically pleasing design for interior and exterior use. The Falcon OHC100A Series is designed for aluminum doors and frames, offering years of maintenance-free performance.
Standard Features
- Economical option for overhead concealed closer
- Retrofittable, matches Jackson hole pattern
- Cast iron construction ensures lasting durability
- Fits inside standard aluminum frame header for improved aesthetics and increased security
- 90° and 105° standard opening with optional hold-open
- Multiple size options: OHC101 (adjustable sizes 1-3), OHC100 (adjustable sizes 3-5)
- Meets UL228
- 5-year warranty
Installation Accessories
- "S" arm, OHC100-SL, OHC100A-SL: Non-handed arm, side load, center hung, steel forge.
- "A" arm, OHC100A-EL, OHC100A-EL: Non-handed arm, end load, center hung, steel forge.
- "VO" arm, OHC100A-VO, OHC100A-VO: Non-handed arm, offset arm w/ slide channel, steel forge.
- "AFK" mounting brackets, OHC100A-AFK: Provides anchorage for adjustable size cylinder to the door frame.
- "GE" pivots, OHC100-GE, OHC100A-GE: Non-handed, adjustable height, center hung, used with side load arm.
- "DP" pivots, OHC100-DP, OHC100A-DP: Non-handed, adjustable height, center hung, used with end load arm.
8200 Series
The Falcon 8200 Series automatic operator is a smart solution for improving accessibility, designed for applications like assisted living and ambulatory care where ease of use is critical. It offers dependable performance at an affordable price, with a small footprint and elegant design.
Key Features
- Small footprint and elegant design
- Steel aluminum finished cover for aesthetic appeal
- Intelligent control box with adjustable features for precise door operation
- One-piece mounting bracket reduces parts and installation time
- Non-handed motor gearbox functions as a size three door closer in manual operation
- SmartLatch: Senses and overcomes external pressure conditions with graduated energy assist for secure latching.
- Push 'n' Go: Selectable feature allows door to open automatically upon sensing pressure.
- Open position learning: Automatically sets opening position and detects obstructions to prevent damage.
- Pre-load strike assist: Removes load on strike lip with a one-second delay for automatic door release and opening.
- LED light illumination on control box signals accurate installation and aids connection diagnostics.
- On-board power supply (12 VAC) powers actuators and receivers.
- Adjustable features: Hold-open time delay, Backcheck speed, Backcheck/latch position, Opening/closing speed.
Specifications
- Header length: 26"
- Mounting: Surface mount
- Handing: Non-handed
- Cycle tested: 1 million gear box cycles
- Door weight: Up to 200 pounds (Consult technical services for doors over 200 lbs)
Actuators and Accessories
- Push plates: Wall mount (6" Round), Jamb mount (1 3/4" x 4 3/4").
- Mounting boxes: Flush mount, Surface mount.
- Weather ring.
- Wireless transmitters & receiver: Transmitter (wall mount, jamb mount, handheld), Receiver (wireless receiver with sequencing function).
Installation Dimensions
Diagrams illustrate 26" Push, Pull, and Drop systems with key mounting dimensions.
How to Order
SC70A Series
| Cylinder | Cover | Arm | Finish | Accessories |
|---|---|---|---|---|
| STD, DEL** | Full cover | RW/PA, HW/PA, HD, DS, DS/HO, SS, SS/HO, FA, FA/HO | Matte black**, Aluminum, Dark bronze, Brass* | SC70A-30, SC70A-61, SC70A-62A, SC70A-18, SC70A-18PA, SC70A-72 |
*Contact customer service at 1-877-671-7011 for lead time information. **Matte Black (622) is not available for Delayed action cylinders. SC71A models are adjustable sizes 1-6.
SC80A Series
| Cylinder | Cover | Arm | Finish | Accessories |
|---|---|---|---|---|
| STD, DEL** | Slim cover, Full cover | RW/PA, HW/PA, HD, DS, DS/HO, SS, SS/HO | Matte black**, Aluminum, Dark bronze, Brass* | SC80A-30, SC80A-61, SC80A-62A, SC80A-18, SC80A-18FC, SC80A-18PA, SC80A-18PAFC, SC80A-72, SC80A-72FC |
*Contact customer service at 1-877-671-7011 for lead time information. **Matte Black (622) is not available for Delayed action cylinders. SC81A models have adjustable sizes 1-6.
SC60A Series
| Cylinder | Cover | Arm | Finish | Accessories |
|---|---|---|---|---|
| STD** | Slim cover | RW/PA, HW/PA, HD, DS, DS/HO, SS, SS/HO | Matte black, Aluminum, Dark bronze, Brass | SC60A-30, SC60A-61, SC60A-62A, SC60A-18, SC60A-18PA, SC60A-72 |
**SC60A Series comes standard with less cover; all models have adjustable sizes 1-5.
SC90A Series
| Cylinder | Size | Cover | Arm | Finish | Accessories |
|---|---|---|---|---|---|
| STD* | 1, 3, 4 | Slim cover | RW/PA, HW/PA | Aluminum, Dark bronze | SC90A-30, SC90A-61, SC90A-62A, SC90A-18, SC90A-18PA, SC90A-72 |
*STD comes with less cover and adjustable backcheck. SC91A models use SC91A-3077PA/3049PA arms. SC93A/94A models use SC90A-3077PA arm and accessories SC90A-18, SC90A-18PA, SC90A-72.
OHC100 Series
| Standard/Hold Open | Cylinder Size | Arm | Finish | Accessories |
|---|---|---|---|---|
| STD, HO | 1-3, 3-5 | S, A, VO | Dark bronze, Aluminum | AFK bracket, GE pivot*, DP pivot* |
*Not available with VO arm type. OHC101 is sizes 1-3, OHC100 is sizes 3-5. Dark bronze finish (695) is only for OHC100 cylinder finish and available on VO arms. Aluminum finish (689) is only finish for OHC100 arms except VO arms.
8200 Series
| Standard | Cylinder Size | Cover | Finish | Arm | Accessories |
|---|---|---|---|---|---|
| STD | 3 | Full cover | Aluminum | Push, Pull | 8310-XXX (various actuators/accessories) |
Cylinder Options
- Standard cylinder (STD): Provides main speed control from maximum opening to latching, with hydraulic backcheck controlling the swing from approximately 70° to maximum opening.
- Delayed action cylinder (DEL): Features separate adjustable delayed closing from maximum opening to approximately 70°, followed by main speed and latch control. Hydraulic backcheck functions similarly to the standard cylinder.
Competitive Cross Reference
Surface Closer Cross Reference
| Falcon | Norton | Hager | dormakaba | Accentra | Sargent | Corbin/Best |
|---|---|---|---|---|---|---|
| SC60A | 1600 | 5300 | QDC300 | 51 | 1131 | SL6000 |
| SC70A | 7500 | 5100 | QDC100 | 4400 | 1431 | DC8000 HD8000 |
| SC80A | 8500 | 5200 | QDC200 | 3000 | 1331 | DC3000 HD7000 |
| SC90A | 1700 | 5400 | 1100 |
Concealed Closer Cross Reference
| Falcon | dormakaba | Global | International | Jackson | Kawneer | Sentinel |
|---|---|---|---|---|---|---|
| OHC100 Series | RTS88 | TC7000 Series | 200, 300, 500 | 20-330 Husky II | 30 Series |
Sample Specifications
2.01 Closers and Door Control Devices:
- Manual closers for accessible doors must comply with ANSI A117.1 for opening force and delayed action closing.
- Conformity required to ANSI A156.4, grade 1, NFPA 80, NFPA 101, and UL10C.
- Closers shall be aluminum construction with steel lever arms, featuring independent adjusting valves for closing, latching, and backcheck. Hydraulic regulation must be controlled by tamper-proof, non-critical screw valves. All closer adjustments must be shielded by a plastic cover after installation. Pressure Relief Valves (PRV) are not permitted.
- Full rack-and-pinion type closer with single-piece forged piston, chrome silicon steel spring, and non-critical screw valves for backcheck, main speed, and latch.
- Closers shall be non-sized and field adjustable from size 1 to 6.
- Large cylinder non-sized closers must have a minimum 1 1/2" diameter piston.
- Install closers to allow maximum opening degree, with backcheck activating sufficiently before the stop position to cushion the swing and prevent door/frame damage. Closers should not be used to stop door travel.
- Unless specified otherwise, install closers with a thru-bolt mounting method on metal and wood doors. Do not use thru-bolt if special blocking is specified in the wood door specification. Coordinate with wood door specifications.
- Available manufacturers are subject to compliance with requirements; refer to competitive cross-reference.
About Allegion
Allegion (NYSE: ALLE) designs and manufactures innovative security and access solutions. The company pioneers safety with brands like CISA®, Interflex®, LCN®, Schlage®, SimonsVoss®, and Von Duprin®. Allegion's comprehensive portfolio of hardware, software, and electronic solutions is sold globally, covering residential and commercial locks, door closers, exit devices, steel doors and frames, access control, and workforce productivity systems. Visit www.allegion.com for more information.
