User Manual for Wzatco models including: 4K UHD Smart Laser Projector, 4K UHD, Smart Laser Projector, Laser Projector
Wzatco Bliss projector User Manual – FIXLIB – user manuals library
Demo Videos
File Info : application/pdf, 14 Pages, 987.28KB
DocumentDocumentWZATCO BLISS 4K UHD Smart Laser Projector Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. User Manual Import Safety Instrucons - Please read the following Import Safety Instructions before starting to use the projector. - Please keep this user manual for future reference. - Please read all warnings and follow all instructions. Setup - Do not place this product in any equipment accessories that generate strong magnetic field. - Do not place this product in the place of fire alarm. - Do not place this product in an extremely hot, cold or humid environment. - Leave at least 20 "(50 cm) clearance around the projector to ensure proper ventilation. - Place the projector in a well-ventilated area. Please do not prevent any objects on the projector, so as not to affect the heat dissipation. - Do not place the projector on an uneven or unstable surface. The projector may fall, resulting in personal injury or projector failure. - If the projector tilts more than 10 degrees to the left or right, do not use it if the tilt angle is no more than 15 ° forward or backward. - Do not put any heavy objects on the projector or connecting line. - Do not place the projector vertically. Otherwise, the projector may fall, resulting in personal injury or projector failure. - Do not expose the projector to direct sunlight or other continuous heat sources. Do not install it next to any heat source, such as radiator, heat regulator, stove, or other equipment (including amplifier) that may raise the projector temperature to a dangerous level. - Do not place liquid near or on the projector. If the liquid splashes into the projector, it will cause the projector to malfunction. If the projector is damp, please disconnect it from the power supply and call the local service center to repair the projector. 01 02 - When the projector is running, you may feel that hot air and smell are discharged from the ventilation grille. This is a normal phenomenon, not a product defect. - Do not attempt to misinterpret the safe use of polarization or grounding type plugs. The polar plug has two inserts, one wide and one narrow. The grounding type plug has two plugs and one grounding plug. The wide insert and grounding insert are used to ensure the safety of users. If the plug cannot be inserted into the socket, use the adapter and do not try to force the plug into the socket. - When the projector is working, do not block the projection lens with any object, otherwise the object will become hot, deformed or even catch fire. - Do not unplug the grounding plug when connecting to the power socket. Make sure that the grounding tab is always inserted. - Prevent the power cord from being trampled or squeezed, especially at the plug and the connection point with the projector. - Voltage instability in some countries. According to the design, the projector can operate safely in the AC voltage range of 100 to 240 volts, but it cannot work in case of power failure or voltage fluctuation exceeding ± 10 volts. In areas where voltage fluctuation or power failure may occur, it is recommended that you connect the projector through power regulator, surge protector or uninterruptible power supply (UPS). - Only connectors / Accessories specified by the manufacturer may be used. - Do not look directly at the projector lens during use. Strong light beams can damage the eyes. - If you find smoke, abnormal noise or peculiar smell, please turn off the projector immediately and contact Supplier. It is dangerous to continue using projection opportunities. - If the projector is not used for a long time, please unplug the power cord from the AC socket. 03 Repair Do not disassemble the projector by yourself. In case of contact with live parts, the dangerous high voltage inside may cause death. Do not replace any electronic components unless you have unplugged the projector. During operation, the temperature of the projector will become very high. Allow the projector to cool for about 45 minutes before removing the components for replacement. All maintenance work should be handled by qualified maintenance personnel. Laser Safety 04 Whats' In the Box Laser Projector AAA Batteries Remote Control Power Cable User Manual 05 Cleaning Cloth Projector Diagram Back View 4.Power Input 5.USB 6.HDMI 1 7.HDMI 2 / ARC 8.Audio Out 9.AV In 10.LAN Top View 1.Power Switch 2.Lens 3.Eye Protection Sensor 06 Connectors And Ports Boom View 11.Height Adjust Wheel 12.Screw HolesM4 07 08 Remote Control Introducon Turn the projector on or off Move through the Menu Confirm your selection Return to the previous screen or action Go to the Home Page To Set the display Volume up/down Mute or resume the sound 09 Infrared Control There is an infrared (IR) sensor in the center directly in front of the laser projector, hold the remote control and keep it within 30 degrees of the remote-control sensor. Right angle to get the normal remote-control function. The distance between the remote control and the sensor must not exceed 8 meters (about 26 feet). Do not place any obstructions in front of the projector's infrared sensor to prevent blocking the infrared beam. Bluetooth Paring Ensure that the remote is within a few feet of the front of the projector before paring Press and hold the Return and Menu buttons for about 5 seconds to enter bluetooth pairing mode, If the pairing is successful, the screen will display "Remote Connected". If the Bluetooth connection is disconnected, repeat the above to restore the Bluetooth connection. 10 Install the Baeries 1. Open the battery cover 2. Install the batteries 3. Close the battery cover Install the Baeries Posion the Laser Projector The room layout and the design of the room will be the most important factors in choosing where to place the projector. Consider the following when selecting a location: The size, shape and position of your screen Location of a suite power outlet Ensure the projector has sufficient space around it for airflow. The projector is designed to be installed in one of the following locations. 11 Desktopfront projection Desktoprear projection Ceiling mountedfront projection Ceiling mountedrear projection Note 1.A rear projection screen is required to use the rear projection function. 2.Please use M4*12 mm Screws when mounting the projector on the ceiling. 12 Power On Projecon Dimensions Connect the power cord to the AC IN Jack at the rear of the projector. Plug the power code into a power outlet. Press the power switch to power on, the power indicator will flash during the startup process. 13 Projecon picture D H SD Projecon picture Image SD 80" 90" 100 " 120 " 150 " Projection Distance (ft) 0.46 0.62 0.79 1.1 2 1.6 1 Projection Height (ft) 0.95 1.0 5 1.1 5 1.3 5 1.6 4 14 Image Adjustment Adjust Image Height Turn the adjustment wheel backward to the lowest height. Adjust image Size Adjust a regular rectangle that is smaller than the screen and parallel to all four sides of the screen. Move backward/forward the laser projector to adjust the projection image to be as large as the screen. 15 16 Adjust Fly Angle Keystone correcon If the projection image is still not satisfied, you can use keystone correction to adjust it. Press the Menu Button on the remote control and navigate to Display>Keystone Correction to enter the correction mode. 17 18 First Time Acvaon When the laser projector is activated the first timeyou will need to pair the remote and select preferred Language, network settings and projection mode. Ready to Use If the laser projector enters the home page, it's ready to use. 19 20 Wireless Screen Mirroring Screen Mirroring provides a 2.4G/5G Hz Wi-Fi connection for users to mirror the screen on their personal device. NOTE: Ensure your device is connected to the same network as the projector. For iOS: 1.Access the drop-down control menu. 2.Select the"Screen Mirroring". 3.Choose"Laser-xxxx". For Android: 1.Scan the QR Code to download and install the"Google Home"and open it. 2.Pull to refresh the app and wait for 30 seconds. 3". Laser-xxxx"will now be visible, Select it. 21 22 System Sengs Wireless Network Ethernet Network Check Network Set up Wireless Network Set up Wired Network Check Network Connection Bluetooth Switch Audio Mode Bluetooth Set up Bluetooth Set up Bluetooth Mode Display Brightness mode Image Parameters Keystone Correction Focus MEMC Projection Mode Boot Source Select the laser projector Brightness mode Adjust the image mode, brightness contrast, saturation, sharpness, hue and color temperature Adjust the image shape Manually adjust the focus Switch motion estimation motion compensation Select the projection mode Select the default input source 23 Touch Tones Audio Mode Dolby Audio Audio Output HDMI1 HDMI2 ARC USB AV System Version Update via USB Drive IR Motion Detection Input Method Sleep Time Format Time Zone Selection Language Settings Unknown Source About Factory Reset Audio Switch touch tones Select Audio Mode Switch Dolby audio effect Select audio output Input source Select the signal source to HDMI1 Select the signal source to HDMI2 ARC Select the signal source to USB Select the signal source to AV General Display current system version Update system via USB Drive Eye Protection Switch Select input method Set sleep time for laser projector Select time format: 12H/24H Select time zone Select display language Install unknown source app switch Display laser projector basic information Reset the laser projector to factory settings 24 Specificaons Specifications are subject to change without notice. Spec Product name Product Dimensions Product Weight Light Source Display Technology Native Resolution Color Gamut Contrast Ratio Throw Ratio Projection CPU RAM ROM Wi-Fi System HDR10 MEMC Screen Mirroring Eye Protection Dolby Audio Speaker Noise Parameters Laser Projector 451*331*99 mm / 17.8*13.1*3.9 inches 6.85kg / 15.1lbs ALPD .47 DMD DLP 3840*2160(XPR) Rec.709 3000:1(Typ.) 0.233:1 up to 150'' MT9669 3GB 32GB 802.11ac 2.4G/5G 1T1R Android 9.0 Yes Yes Yes Yes Yes 15W*2 Woofers 15W*2 Tweeters 32dB @Standard/25/1m Power Consumption 300W Input 100-240V~50/60Hz, 2.5A 25 Interfaces Video Format Audio Format Image Format Document Format HDMI2.0 *1HDMI 2.0 / ARC *1USB2.0 *2 Audio out *1 AV in 3.5mm *1LAN *1 MP4/MPEG/VOB/MKV/TS/AVI/FLV/3GPP/RMVB MP3/AC3/FLAC/WAV/M4A JPG/JPEG/PNG/BMP/TIF .doc/.docx/.txt/.pdf Specificaons What If the laser projector can't turn on? ·Please check the laser projector is properly connected to a power outlet. ·If the laser projector is too hotPlease wait for 2H to cool down and Restart it. What If the image does not appear ·Please check the connection and make sure to select the correct input source. ·Power off the laser projector and unplug the power cable, plug it in again after 1 mins and power on again. What if the image is blurred? ·Please try to manually adjust the focus with remote control. ·Please try to move backward/forward the laser projector. What if there is no sound in the laser projector? ·Please try to unmute and volume up. ·Please check the connection and make sure to select the correct audio output. ·Please check whether the audio file format is supported. (See Specifications) What if the remote does not work? The batteries may be depleted, please try to change batteries. Please check there are not any obstacles between the remote and the projector. The remote may be too far from the projector. Please use the remote within 26 feet of the laser projector. 26Adobe PDF library 15.00 Adobe Illustrator CC 2017 (Windows)