Manuals+

BitFenix SAKIELL ALL-IN-ONE 240MM/360MM Liquid Cooler with ARGB Fans

Package Contents

The BitFenix SAKIELL AIO Liquid Cooler is available in two sizes: 240mm and 360mm, both featuring ARGB fans.

SAKIEL AIO ARGB 240

SAKIEL AIO ARGB 360

Accessories & Hardware

Category Item Quantity
Adapter 3-Pin A-RGB Motherboard Adapter (730 mm) 1 X
Cable 4-Pin PWM Splitter Cable (50 mm) 1 X
Mounting Hardware Intel 1851/1700/1200/1150/1151/1155 Backplate 1 X
Mounting Hardware AMD AM4/AM5 Bracket 1 X
Thermal Interface BITFENIX TF10 EXTREME Thermal Paste 1 X
Mounting Hardware AMD/Intel Stand-off 4 X
Mounting Hardware Intel socket mounting holes 4 X
Mounting Hardware Thumb Nut 4 X
Mounting Hardware Intel socket holder 4 X
Mounting Hardware Plastic Stand-off 6 X
Screws 31mm Fan Screw (for 240mm/360mm radiators) 8 X / 12 X
Screws 5mm Radiator Screw (for 240mm/360mm radiators) 8 X / 12 X

Installation Instructions

AMD Socket Installation

Follow these steps to install the pump unit on an AMD socket motherboard.

  1. 1. Remove the stock mounting brackets from the motherboard.
  2. 2. Use the 4x plastic stand-offs.
  3. 3. Combine the metal stand-off parts with the plastic parts (4 sets).
  4. 4. Mount the 4x AM4 stand-offs to the motherboard.
  5. 5. Push the AMD bracket onto the pump unit.
  6. 6. ❗ Before mounting the CPU block, peel off the protective film from the underside of the cooler.
  7. 7. Apply thermal paste to the CPU surface. The tube contains enough for approximately 1 or 2 applications.
  8. 8. Mount the pump unit to the stand-offs on the motherboard using the 4x thumb nuts.
Screw Sequence Suggestion: Please follow the numbered sequence (11️⃣→22️⃣→33️⃣→44️⃣) to lock the bracket and ensure the thumb screws are well installed.
Note: First, insert and lightly fasten all screws. Once all screws are in place, gradually and evenly tighten them in stages to ensure uniform pressure on the components and to avoid deformation.

Intel Socket Installation

Follow these steps to install the pump unit on an Intel socket motherboard.

  1. 1. Prepare the Intel Backplate for the correct socket:
    • A: For LGA 1700/1851 sockets
    • B: For LGA 1150/1151/1155/1200 sockets
  2. 2. Use the 4x plastic stand-offs.
  3. 3. Combine the metal stand-off parts with the plastic parts (4 sets).
  4. 4. Mount the 4x Intel stand-offs to the motherboard.
  5. 5. Push the Intel bracket onto the pump unit.
  6. 6. ❗ Before mounting the CPU block, peel off the protective film from the underside of the cooler.
  7. 7. Apply thermal paste to the CPU surface. The tube contains enough for approximately 1 or 2 applications.
  8. 8. Mount the pump unit to the stand-offs on the motherboard using the 4x thumb nuts.
Screw Sequence Suggestion: Please follow the numbered sequence (11️⃣→22️⃣→33️⃣→44️⃣) to lock the bracket and ensure the thumb screws are well installed.
Note: First, insert and lightly fasten all screws. Once all screws are in place, gradually and evenly tighten them in stages to ensure uniform pressure on the components and to avoid deformation.

Mount the Radiator and Fans

Please install the fans to the radiator before mounting it into the chassis.

Connect Pump / Fan / ARGB

Properly connect the pump, fans, and ARGB lighting for optimal performance and control.

Pump and Fan Connections

  1. 1. Connect the pump PWM cable to the pump unit.
  2. 2. Connect the fan and pump cables to the motherboard:
    • For motherboards with a single CPU header: Connect the 4-pin header (from the fan or splitter cable) to CPU fans and the 3-pin header to the pump.
    • If your motherboard has 2x CPU headers or dedicated Pump headers, you can connect the pump and fans individually for more precise control (without using the PWM splitter cable).

Fan Cable Daisy-Chaining and PWM Connection

  1. 1. Connect the fans together using their daisy-chain cables.
  2. 2. Connect the PWM header of the fan (or the 4-pin header from the PWM splitter cable if using a single CPU header motherboard) to the CPU header on the motherboard.

ARGB Cable Daisy-Chaining and Connection

  1. 1. Connect the ARGB components together using their daisy-chain cables.
  2. 2. Connect the ARGB daisy-chain cable to the ARGB header on your motherboard or a compatible ARGB controller.
This connection allows for synchronized ARGB lighting effects. You can connect other brands' ARGB products to the same header if compatible.

Support & Warranty

For any questions regarding support or warranty, please visit the BitFenix Support Center or the official BitFenix website.

Follow BitFenix on social media: [Facebook] [Twitter] [Instagram] [YouTube]

©2025 BITFENIX Co., Ltd. All Rights Reserved. All trademarks are registered to their respective owners.

Models: 360, SAKIEL All in One 240mm 360mm Liquid Cooler with ARGB Fans, SAKIEL, All in One 240mm 360mm Liquid Cooler with ARGB Fans, 240mm 360mm Liquid Cooler with ARGB Fans, Liquid Cooler with ARGB Fans, Cooler with ARGB Fans, ARGB Fans, Fans, Cooler
SAKIEL QIG Adobe Acrobat 25.1 Adobe Acrobat 25.1 Image Conversion Plug-in

Related Documents

Preview BitFenix Kuzy 240/360mm Digital Water Cooler - Advanced CPU Cooling
Explore the BitFenix Kuzy, a 240mm and 360mm digital water cooler featuring a unique 7-segment LCD screen, ARGB lighting, and advanced cooling technology for high-performance CPUs. Compatible with major motherboard RGB synchronization.
Preview BitFenix KUZY AIO Liquid Cooler Installation Guide - 240mm & 360mm
Detailed installation guide for the BitFenix KUZY All-in-One (AIO) liquid cooler, covering both 240mm and 360mm models. Learn how to mount the radiator, fans, and pump for optimal CPU cooling performance.