Instruction Manual for Lowes models including: 6248253 Swivel Joint Pendant Light Fixture, 6248253, Swivel Joint Pendant Light Fixture, Joint Pendant Light Fixture, Pendant Light Fixture, Light Fixture
5 days ago — Item Number: 6248253. WARNING (To reduce the risk of fire, electric shock, or personal injury):. 1. We suggest installation by a licensed electrician.
5 days ago —
Item Number: 6248253 WARNING (To reduce the risk of fire, electric shock, or personal injury): 1. We suggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at a later time. 3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. » Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the "OFF" position. » Place the wall switch in the "OFF" position. 4. Mounting surface should be clean, dry, flat, strong enough and 1/4" larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16" should be corrected as required. 5. Make sure that the ceiling or wall can stand the weight of the lamp before installation. 6. Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb. 7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp. 8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly. 9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products. IMAGE FOR FINISHED PRODUCT: TOOLS REQUIRED Before starting assembly and installation please prepare the needed (NOT INCLUDED): tools as below picture Ladder Philips Head or Flat Blade Screwdriver Electrical Tape Pliers Wire Cutter/Stripper Page: - 1 - / 4 PARTS TYPE & QTY INCLUDED: (C) Mounting plate (1) (D) Green ground screw (1) (E) Canopy (1) (F) Swivel joint (1) (G) Knob nut (2) (H) Tube (I) Socket (1) (J) Lampshade (1) ACCESSORIES & QTY ENCLOSED: (A) Plastic wire connector (3) (B) Mounting screw (2) ASSEMBLY & INSTALLATION INSTRUCTIONS: 1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration. 2. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done. » Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the "OFF" position. » Place the wall switch in the "OFF" position. 3 » Unscrew knob nuts (G) from canopy (E). Remove mounting plate (C). Page: - 2 - / 4 4 » 1) According to your desired hanging height to choose and use tubes (H). Then pass the fixture wires through the chosen tubes (H), swivel joint (F) and canopy (E). 2) Be sure that all the threaded pipes are tightened, then screw the chosen tubes (H) onto swivel joint (F). Hand tighten till snug. 5 » Carefully pass supply wires through mounting plate (C). Secure mounting plate (C) to the outlet box with mounting screws (B). NOTE: the side of mounting plate (C) marked "GND" must face out. 6 » Make wire connections Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES. Connect ground wires according to the chart below A B Connect wires according to the chart below Connect Black or Red Supply Wire to: Connect White Supply Wire to: OUTLET BOX GROUND GREEN GROUND SCREW OUTLET BOX GROUND FIXTURE GROUND DIMPLES GREEN GROUND SCREW Black White *Parallel cord (round & smooth) *Parallel cord (square & ridged) FIXTURE GROUND Clear, Brown, Gold or Black without tracer Insulated wire(other than green) with copper conductor Clear, Brown, Gold or Black with tracer Insulated wire(other than green) with silver conductor CUPPED WASHER * Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.) Neutral Wire Page: - 3 - / 4 Twist wires together with plastic wire connector until tightly joined. Wrap each connector with approved electrical tape for a more secure connection. Carefully tuck all wires into the outlet box. 7 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening knob nuts (G) onto the pre-assembled screws in mounting plate (C). Note: canopy (E) should be snug against the ceiling and knob nuts (G). If not, adjust the threaded length on mounting plate (C): · Unscrew the pre-assembled hex nuts. · Screw the pre-assembled screws in or out of mounting plate (C). · When the secure length is achieved, tighten the hex nuts and back to step 7. 8 » Install the bulb (Not included) (Please do not exceed the maximum wattage recommended on the socket.) 9.Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting! ORDERING PARTS Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts. CLEANING To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper. Page: - 4 - / 4Scribus PDF Library 1.5.8.svn