User Guide for ALTEC LANSING models including: S228, 2AD33S228, IMT7000, Shockwave Wireless Bluetooth Party Speaker, IMT7000 Shockwave Wireless Bluetooth Party Speaker, Wireless Bluetooth Party Speaker, Bluetooth Party Speaker, Party Speaker, Speaker
FLYBALL ELECTRONIC (SHENZHEN) CO. LTD S228 2AD33S228 2AD33S228 s228
File Info : application/pdf, 12 Pages, 1.42MB
DocumentDocumentIMT7000 IMT7000 IIMMTT77000000 Quick Start Guide Charging Cable (USB-C to USB-A) Brief introduction to buttons on top panel Power Button Press and hold button for 3 seconds to power on or power off speaker Volume Control Decrease volume Previous song Volume Control Increase volume Next song Light Button: Briefly press to turn on/off the light mode and switch the light modes, total 9 modes Bass Button: Briefly press to switch bass mode, total 3 modes. BT & Party-sync Button: Briefly press to enter Bluetooth pairing mode, Press and hold for Bluetooth disconnect, Double-click for party-sync connect or disconnect AUX mode Play/Pause (BT mode only) AUX mode: Short press MUTE Indicators: : Power on (Solid blue) : Bluetooth pairing (Flashing blue quickly), Bluetooth connected (Solid blue), Sync up with other speakers (Flashing blue slowly) : AUX mode cSolid orange : Bass 1, Bass 2, Bass 3 (Solid Blue) Reset to default settings: Press and hold the BASS button for 10S to reset all settings back to factory default. Bluetooth Connection Go to the Bluetooth settings menu on your phone. Make sure that Bluetooth is turned on. Connect to the device listed as "AL Shockwave " AL Shockwave Speaker will enter into BT mode when powered on; Briefly press the BT button to enter into BT mode; If you want to change to a different BT device when already paired press and hold the BT button, the speaker will disconnect from its paired device. A different device can now be paired. Party-sync with AL SHOCKWAVE Family AL Shockwave A double press of the BT button is used to enter/exit party-sync mode on extra speakers if you have them as below. Item Number IMT7000 IMT7100 IMT7200 IMT7300 Item name Shockwave Wireless Party Speaker Shockwave 200 Wireless party speaker Shockwave 300 Wireless Party Speaker Shockwave 400 Wireless Party Speaker Pairing Name AL Shockwave AL Shockwave 200 AL Shockwave 300 AL Shockwave 400 The Altec Lansing SHOCKWAVE family has four members that support party-sync. You can mix and match between any of these four models, setting up one speaker as the primary unit connected to up to 100 other speakers all playing in sync. 1. Connect one speaker to your Bluetooth device in the normal way via Bluetooth. 2. Double-press the BT button on the next speaker to enter Party-sync mode, its BT LED will flashes slowly and it will find and connect to the first (primary) speaker. 3. Repeat No 2 if you have more speakers you want to connect. 4. To exit party-sync double press the BT button on the speakers you wish to disconnect and return to normal operation. Notes: Playback volume is adjusted via the first (primary) speaker. The BT playback controls only operate on the first (primary) speaker. Turning off the first (primary) speaker turns off all speakers. All secondary speakers can be turned on/off individually and their light modes changed via their individual controls. LIGHTING CONTROL Briefly press the LIGHTS button to switch lighting mode. (Note: Some modes which use `sound-to-light' need music playing to be visible) Each press moves to the next mode and back round to off. Mode 1: Rotating ring in three colors Mode 2: Flashing to music Mode 3: `Spectrum' Mode 4: `Stacking/re-stacking' lights both sides Mode 5: Rotating lights in multi-colors Mode 6: Breathing on/off Mode 7: Flashing to music, solid lighting when no audio Mode 8: `Bar-graph' in multi-colors Mode 9: Rotating `stacking/re-stacking' lights INPUT/OUTPUT PORTS Descriptions about the various ports on the speaker AUX: For line level or headphone output from audio sources RESET: Button is recessed inside. For use only in the unlikely case of a lock up. Use paperclip or pin to perform restart of the speaker. USB OUT: For charging your mobile devices DC IN: USB-C port for charging your speaker from suitable USB socket/PSU. Charging-in indicator: Solid red when charging, will be off when fully charged Power Audio: 60W (Peak) Total Drivers Units: 4" Bass, 2" Tweeter + Rear Auxiliary Bass Radiator. S/N: 70dB Distortion: 0.5% 1K,1W) USB-A output: 5V 1A USB-C charging Input: 5V 1A Dimensions: L205*H315*D172 mm Length of Charging cable (USB-A to USB-C): 90cm Supplier's Declaration of Conformity 47 CFR § 2.1077 Compliance Information Unique Identifier Trade Name: Altec Lansing Model No.: IMT7000 Responsible Party U.S. Contact Information US Company Name: SAKAR INTERNATIONAL INC. Address: Edison, NJ 08817 Telephone number or internet contact information: 855-292-4087 RF Exposure Compliance This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions All the safety and operating instructions should be read before this product is operated. 2.Keep these instructions The safety and operating instructions should be retained for future reference. 3.Heed all warnings All warnings on the appliance and in the operating instructions should be adhered to. 4.Follow all instructions All operating and use instructions should be followed. 5.Do not use this apparatus near water The appliance should not be used near water or moisture for example, in a wet basement or near a swimming pool, and the like. 6.Clean only with dry cloth. 7.Do not block any ventilation openings. Install in accordance with the manufacture's instructions. 8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10.Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus. 11.Only use attachments/accessories specified by the manufacturer. 12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13.Unplug the apparatus during lightning storms or when unused for long periods of time. 14.Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15.CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. 16.WARNINGTo reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects filled with liquids, such as vases, shall not be placed on apparatus. 17.WARNINGFor the terminals marked with symbol of " " may be of sufficient magnitude to constitute a risk of electric shock. The external wiring connected to the terminals requires installation by an instructed person or the used of ready-made leads or cords. 18. This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth. ATTENTION:RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR 19. - This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. - Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel. - The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.