User Guide for CST models including: TP-48, TP-48 Customize Labels Printer, Customize Labels Printer, Labels Printer, Printer
Принтер этикеток CST TP-48 203dpi SU Ethernet: купить в Новосибирске — низкая цена 19780₽ в официальном интернет-магазине ЦТО «Такском-Касса»
Appearance and Components-1-Packing List ！Note: The packing materials are actually based on the order. -2-TP-48 Quick Start Guide Printer AC Adapter Power Cord Label Roll Ribbon Spindles
Купить Принтер этикеток CST TP-48 203dpi SU Ethernet – выгодная цена 19780 ₽ на принтеры этикеток ЦТО «Такском-Касса»
CST Quick Start Guide TP-48 Cauon: This is a Class A product. In a domesc environment this product may cause radio interference in which the user may be required to take adequate measures. -1- Packing List Printer AC Adapter Power Cord Label Roll Ribbon Spindles Quick Start Guide CD Quick Start Guide USB Cable Empty Ribbon Core Note: The packing materials are actually based on the order. Appearance and Components Front View Power Buon Rear View Ribbon Printer Cover Inside View Status Indicator Feed Buon USB Port (Type A) Cover Open Buons USB Port Front Cover (Type B) Power Receptacle Serial Port Ethernet Port Moveable Roll Holders Mechanism Lock Printer Mechanism Back Label Sensor Moveable Label Guides Platen Locking Tab Front Label Sensor Note: The packing materials are actually based on the order. -2- FCC WARNING This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause unde sired operaon. Any changes or modificaons not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference when the equipment isoperated in a commercial environment. This equipment generates, uses, and canradiate radio frequency energy and, if not installed and used in accordance with the instrucon manual, may cause harmful interference to radio communicaons. Operaonof this equipment in a residenal area is likely to cause harmful interference in whichcase the user will be required to correct the interference at his own expense. -- Reorient or relocate the receiving antenna. -- Increase the separaon between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV tech nician for help. To maintain compliance with FCC's RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. Power Connecon 1.Connect the AC adapter to power receptacle. 2.Connect the power cord to AC adapter. 3.Connect the other end of power cord to the outlet. Varies by regions Loading the Roll 1.Press to open the printer cover and mechanism. 2.Pull the roll holders open and place the roll between them.Press down the locking tab. Loading the Ribbon 1.Install the ribbon module. 2.Insert the le part of supply spindle and then the right part spindle. Sckup Ribbon Supply Spindle Ribbon Rewind Spindle 3.Press down the printer mechanism. 4.Insert the le part of rewind spindle and then the right part. 3.Pass the labels through label guides and adjust label guides to label's width. Cauon: the tear bar of this printer contains a sharp edge. Please do NOT touch it. -3- 5.Wind the core 2~3 ciPress down the mechanism and close the cover. 6.Press down the mechanism and close the cover. Note: Please refer to windows driver installation in TP-48 User Manual. -4-GPL Ghostscript 9.25 Adobe Illustrator CC 22.0 (Windows)