Raised Garden Bed Kits | Elevated Planters – EverBloom Garden
Garden
Raised Garden Bed Kits | Elevated Planters – EverBloom Garden
Installation Guide for Everbloom models including: E213612 Deep Trough Planter Box, E213612, Deep Trough Planter Box, Trough Planter Box, Planter Box
6 giorni fa — Eleven depths are available by changing the sequence of the boards and position of the bottom boards, as shown in below images. You can choose according to ...
Everbloom Deep Trough Mobile Planter 12 x 36 x 24-in Brown K2112 | RONA
File Info : application/pdf, 19 Pages, 10.64MB
DocumentDocumentDeep Trough Planter Box Installation Guide Thank You! You're only a few steps away from your perfect vegetable garden or elevated planter. We hope you enjoy! Before You Start Please read the instructions carefully to familiarize yourself with every detail and step involved. Keep this manual for future reference. Find a suitable space to assemble your new Trough Planter Box. You need at least 37" x 13" (94 x 33cm) for the finished product. A flat and firm area (like a garage floor or flat yard space) is perfect! The only tool you may need is a rubber mallet. Important Notes Small parts are included; we advise you to keep them away from children and pets. We also suggest having another person help you assemble. Maximum Load Capacity: approximately 4 cu. ft. of soil Subscribe at www.everbloom-garden.com for extra savings and upgrading information! Everbloom-Garden.com Questions or Comments? Email us at service@everbloom-garden.com Model# E213612 / E213612G Dimensions 36" L x 12" W x 21" H 1 Parts List Deep Trough Planter Box - 36" L x 12" W x 21" H Left Corner Post X 2 Top Right Corner Post X 2 Top Long Board A X 2 Long Board B X 2 Long Support Board X 2 Short Board A X 4 Short Board B X 2 Bottom Bottom 240mm 240mm Bottom Board A X 2 Bottom Board B X 4 Post Cap X 4 + 2pc replacement 900mm 900mm 900mm 280mm 280mm 2 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H Eleven depths are available by changing the sequence of the boards and position of the bottom boards, as shown in below images. You can choose according to different needs first. * For depth of 2.5", 5", 7.25", 9.5",9.75", 12", 14.4" and 17" as shown in Image 1, 2, 3 and 4, please refer to steps from page 4. * For depth of 4.75", 7" and 11.9" as shown in Image 2, 3 and Image 4, please refer to steps from page 10. IMAGE 1 Depth 2.5", 5" Long Support Board Long Board A 2.5" (6.5cm) 5" (12.8cm) Long Board B Bottom Board IMAGE 2 Depth 4.75", 7.25", 9.75" Long Board B Long Support Board 4.75" (12cm) 7.25" 9.75" (18.4cm) (24.7cm) Long Board A Bottom Board IMAGE 3 Depth 7", 9.5", 12" IMAGE 4 Depth 11.9", 14.4", 17" Long Board A Long Support Board Long Board B 7" 9.5" 12" (18cm) (24cm) (30.9cm) Bottom Board Long Board B Long Board A Long Support Board 11.9" 14.4" 17" (30.2cm) (36.5cm) (43cm) Bottom Board 3 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H For the deeper planting depths of 17", please follow steps below. For other depths, the assembly methods are similar, just pay attention to the sequence of the boards and position of the bottom boards, please refer to page 3. Start by making sure each corner post is oriented correctly, as shown in Image 3. Slide one short board A into the corner brackets from above. Note: The short boards need to be placed in the inward "U" shape of the brackets, as shown in Image 4. IMAGE 3 IMAGE 4 Top Short Board A Bottom Left Corner Post Right Corner Post 4 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H Slide another short board A into the other two corner brackets from above, as shown in Image 5. IMAGE 5 Left Corner Post Right Corner Post Short Board A Right Corner Post Left Corner Post Short Board A 5 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H With the help of another person holding the 2 assembled parts, slide the 2 long support boards into the brackets from above. Make sure that one support board goes straight to the bottom, while the other one stays in the middle of the way (don't push it to the bottom), with the top edge between the 4th and 5th holes of the post. IMAGE 6 Long Support Board Long Support Board 4 holes in the middle of the way to the bottom 6 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H Put the bottom boards on the lower slot of long support boards. Make sure the 2 ends of these bottom boards go into the slot and rest in them with enough contact as shown in Image 7. Adjust the height of the higher long support board slightly to hold these bottom boards if necessary. IMAGE 7 Bottom Board B Bottom Board A slots Bottom Board A Bottom Board B Bottom Board B Bottom Board B Long Support Board Long Support Board 7 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H Push down the higher long support board to the bottom, as shown in Image 8. IMAGE 8 Long Support Board Long Support Board 8 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H Slide the remaining boards into place, as shown in Image 9. Now you get an trough planter box with 17" planting depth. Then, go to page 15, and follow the steps afterwards. NoteIf you want to add trellis kit onto this bed, please assemble the extension connectors before this step, to avoid disassembling the boards later. IMAGE 9 Long Board B X 2 Short Board B X 2 Long Board A X 2 Short Board A X 2 9 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H For the planting depth of 11.9", please follow steps below. For depth of 4.75" or 7", the assembly methods are similar, just pay attention to the sequence of the boards and position of the bottom boards, please refer to page 3. Start by making sure each corner post is oriented correctly, as shown in Image 3a. Slide one short board B into the corner brackets from above. Note: The short boards need to be placed in the inward "U" shape of the brackets, as shown in Image 4a. IMAGE 3a IMAGE 4a Top Short Board A Bottom Left Corner Post Right Corner Post 10 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H Slide another short board A into the other two corner brackets from above, as shown in Image 5a. IMAGE 5a Left Corner Post Right Corner Post Short Board A Right Corner Post Left Corner Post Short Board A 11 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H With the help of another person holding the 2 assembled parts, slide the 2 long support boards into the brackets from above to the bottom, as shown in Image 6a. IMAGE 6a Long Support Board Long Support Board 12 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H Put the bottom boards on the long support boards, as shown in Image 7a. IMAGE 7a Bottom Board B Bottom Board B slot Bottom Board A Bottom Board A Bottom Board B Bottom Board B Long Support Board 13 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H Slide the remaining boards into place, as shown in Image 8a. Now you get an trough planter box with 11.9" planting depth. Then, go to page 15, and follow the steps afterwards. NoteIf you want to add trellis kit onto this bed, please assemble the extension connectors before this step, to avoid disassembling the boards later. IMAGE 8a Long Board B X 2 Long Board A X 2 Short Board B X 2 Short Board A X 2 Long Support Board 14 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H If necessary, use your rubber mallet to ensure the boards are tightly in place. Cover the brackets with the 4 end caps, as shown in Image 10. IMAGE 10 Post Cap X 1 Post Cap X 1 Rubber Mallet Post Cap X 1 Post Cap X 1 15 Assembly Deep Trough Planter Box - 36" L x 12" W x 21" H Then you get an Everbloom Deep Trough Planter Box, as shown in Image 11. IMAGE 11 Note: Store the additional caps for future use. 16 Note Deep Trough Planter Box - 36" L x 12" W x 21" H Sometimes there might be a misalignment of the Corner Posts as shown in Image 12 and Image 13, which may result in difficulty of sliding boards into the brackets. Please adjust them to the right position so that they are parallel to each other, and perpendicular to the ground. IMAGE 12 Assembling Problem 1 X IMAGE 13 Assembling Problem 2 X 17 Bloom On. Everbloom-Garden.com US Patent Pending Subscribe at www.everbloom-garden.com for extra savings and upgrading information Distributed by: Dynaforge Trading LLC St. Paul, MN55101 Email: service@everbloom-garden.com