Olimpia Splendid Remote Control Owner's Manual

Contents

• Remote controller Specifications
• Operation buttons
• Indicators on LCD
• How to use the buttons
• Auto operation
• Cooling/Heating/Fan operation
• Dehumidifying operation
• Timer operation
• Handling the remote controller

Remote Controller Specifications

Note: Button designs are based on typical models and may differ slightly from the actual unit purchased. All functions described are accomplished by the unit; if the unit does not have a feature, there is no corresponding operation. In case of discrepancies between illustrations and descriptions, the "USER'S MANUAL" description prevails.

Operation Buttons

ON/OFF Button: Turns the air conditioner ON and OFF.

MODE Button: Cycles through modes: AUTO, COOL, DRY, HEAT (if applicable), FAN.

FAN Button: Selects fan speed: AUTO, LOW, MED, HIGH. (Note: Fan speed cannot be adjusted in AUTO or DRY mode).

SLEEP Button: Activates/deactivates the sleep function for comfortable temperature and energy saving. Available in COOL, HEAT, or AUTO modes.

FRESH Button (RG57A4/BGEF): Activates/deactivates the FRESH function, which uses an ionizer/Plasma Dust Collector to remove impurities.

TURBO Button: Activates/deactivates the Turbo function for rapid cooling or heating to the preset temperature.

SELF CLEAN Button (RG57A4/BGEF): Activates/deactivates the Self Clean function.

UP Button (⬆️): Increases the temperature setting by 1°C increments (up to 30°C).

DOWN Button (⬇️): Decreases the temperature setting by 1°C increments (down to 17°C).

SILENCE/FP Button: Activates/deactivates the SILENCE function for quiet operation. Pressing for over 2 seconds activates/deactivates the 'FP' function (heating mode only, operates at 8°C).

TIMER ON Button: Sets the auto-on timer. Increments by 30 minutes (0.5 hours) up to 10 hours, then by 1 hour up to 24 hours. To cancel, set to 0.0.

TIMER OFF Button: Sets the auto-off timer. Increments by 30 minutes (0.5 hours) up to 10 hours, then by 1 hour up to 24 hours. To cancel, set to 0.0.

SWING Button (RG57A4/BGEF): Starts/stops vertical louver movement and sets left/right airflow direction. Changes angle in 6° increments. Holding for over 2 seconds activates auto swing.

SWING Button (RG57A6/BGE): Starts/stops horizontal louver auto swing.

DIRECT Button (RG57A6/BGE): Changes louver movement and sets up/down airflow direction. Changes angle in 6° increments.

FOLLOW ME Button: Activates the Follow Me feature, displaying the actual room temperature. The remote sends this signal every 3 minutes. The feature cancels if no signal is received for 7 minutes.

LED Button: Disables/activates the indoor display screen.

Indicators on LCD

• Mode Display: Shows AUTO, COOL, DRY, HEAT, FAN.
• ON/OFF Indicator: Displayed when the remote controller is powered ON.
• Battery Display: Indicates battery status (low battery detection).
• ECO: Not available for this unit.
• TIMER ON Indicator (ON): Displayed when TIMER ON time is set.
• TIMER OFF Indicator (OFF): Displayed when TIMER OFF time is set.
• Temperature Display (8.8): Shows set temperature or room temperature, or time under TIMER setting.
• Sleep Mode Indicator: Displayed in Sleep Mode operation.
• Follow Me Indicator: Indicates the air conditioner is operating in Follow Me mode.
• Fresh Indicator: Displayed when the fresh feature is activated (some units).
• Silence Indicator: Displayed when the silence feature is activated.
• Fan Speed Indication: Shows fan speed (Low, Medium, High, Auto).

Note: Figures are for presentation; actual display may show only relative functional signs.

How to Use the Buttons

Auto Operation

1. Ensure the unit is plugged in. The OPERATION indicator will flash.
2. Press MODE to select Auto.
3. Press UP/DOWN to set the desired temperature (17°C-30°C in 1°C increments).
4. Press ON/OFF to start the air conditioner.

Note: In Auto mode, the air conditioner automatically selects Cooling, Fan, or Heating. Fan speed is also automatically controlled. If the mode is not comfortable, select a mode manually.

Cooling/Heating/Fan Operation

1. Ensure the unit is plugged in.
2. Press MODE to select COOL, HEAT (if applicable), or FAN mode.
3. Press UP/DOWN to set the desired temperature (17°C-30°C in 1°C increments).
4. Press FAN to select fan speed (Auto, Low, Med, High).
5. Press ON/OFF to start the air conditioner.

Note: In FAN mode, temperature is not displayed or controlled. Only steps 1, 3, and 4 are applicable.

Dehumidifying Operation

1. Ensure the unit is plugged in. The OPERATION indicator will flash.
2. Press MODE to select DRY mode.
3. Press UP/DOWN to set the desired temperature (17°C-30°C in 1°C increments).
4. Press ON/OFF to start the air conditioner.

Note: In DRY mode, fan speed cannot be adjusted; it is automatically controlled.

Timer Operation

Use the TIMER ON and TIMER OFF buttons to set auto-on and auto-off times.

To set the Auto-on time:

1. Press TIMER ON. The display shows TIMER ON and the last set time.
2. Press TIMER ON repeatedly to set the desired auto-on time. Time increases by 0.5 hours (0-10 hours) and then by 1 hour (10-24 hours).
3. After setting, the remote transmits the signal. The "h" indicator appears and disappears after approximately 2 seconds, and the set temperature reappears.

To set the Auto-off time:

1. Press TIMER OFF. The display shows TIMER OFF and the last set time.
2. Press TIMER OFF repeatedly to set the desired auto-off time. Time increases by 0.5 hours (0-10 hours) and then by 1 hour (10-24 hours).
3. After setting, the remote transmits the signal. The "h" indicator appears and disappears after approximately 2 seconds, and the set temperature reappears.

Combined Timer (Setting both ON and OFF timers simultaneously)

• TIMER OFF → TIMER ON (On → Stop → Start): Set to stop the unit at night and start it in the morning. Example: Stop in 2 hours, start in 10 hours. Press TIMER OFF, set 2.0H, press TIMER ON, set 10H.
• TIMER ON → TIMER OFF (Off → Start → Stop): Set to start the unit before waking and stop it after leaving. Example: Start in 2 hours, stop in 5 hours. Press TIMER ON, set 2.0H, press TIMER OFF, set 5.0H.

Caution: Keep the remote controller within range of the indoor unit's receiver for timer operations. The effective timer settings are in 0.5-hour increments up to 10 hours, then 1-hour increments up to 24 hours.

Handling the Remote Controller

Location of the remote controller:

• Operate within 8 meters, pointing towards the receiver. Reception is confirmed by a beep.
• Ensure the path between the remote and receiver is clear of obstructions (curtains, doors).
• Avoid liquid contact and direct sunlight or heat.
• If the indoor unit's receiver is exposed to direct sunlight, use curtains to prevent malfunction.
• If other appliances react to the remote, relocate them or consult your dealer.
• Handle with care; do not drop or place heavy objects on it.

Using the remote controller holder (optional):

• The holder can be attached to a wall or pillar.
• Check signal reception before installation.
• Install with two screws.
• Move the remote up or down in the holder to install or remove.

Replacing batteries:

Replace batteries when the receiving beep is absent or the indicator fades.

1. The remote uses two R03/LR03X2 dry batteries.
2. Remove the rear cover.
3. Remove old batteries and insert new ones, observing correct polarity (+/-).
4. Reinstall the cover.

Note: Removing batteries erases programming. Reprogram after inserting new batteries.

Cautions for batteries:

• Do not mix old/new or different types of batteries.
• Remove batteries if the remote will not be used for 2-3 months.
• Dispose of batteries properly according to local regulations.