Instruction Manual for SENECA models including: Z-KEY-2ETH, Z-KEY-2ETH-P, Z-KEY-2ETH-P ModBUS or Ethernet Gateway, ModBUS or Ethernet Gateway, Ethernet Gateway, Gateway
Z-KEY-2ETH
INSTALLATION MANUAL Z-KEY-2ETH Z-KEY-2ETH-P PRELIMINARY WARNINGS The word WARNING preceded by the symbol indicates conditions or actions that put the user's safety at risk. The word ATTENTION preceded by the symbol indicates conditions or actions that might damage the instrument or the connected equipment. The warranty shall become null and void in the event of improper use or tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if the instructions contained in this manual are not followed. WARNING: The full content of this manual must be read before any operation. The module must only be used by qualified electricians. Specific documentation is available via QR-CODE shown on page 1. The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to electrostatic discharges. Take appropriate measures during any operation. Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling). The symbol on the product or its packaging shows the product must be surrendered to a collection centre authorized to recycle electrical and electronic waste. DOCUMENTATION Z-KEY-2ETH DOCUMENTATION Z-KEY-2ETH-P SENECA s.r.l.; Via Austria, 26 35127 PADOVA ITALY; Tel. +39.049.8705359 - Fax +39.049.8706287 CONTACT INFORMATION Technical support support@seneca.it Product information sales@seneca.it This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised. The content of this document corresponds to the described products and technologies. Stated data may be modified or supplemented for technical and/or sales purposes. MI00573-3-EN INSTALLATION MANUAL 1/4 MODULE LAYOUT 17,5 mm 102,5 mm 111 mm Dimensions: 17.5 x 102.5 x 111 mm, Weight: 100 g; Enclosure: PA6, black SIGNALS VIA LED ON FRONT PANEL LED ET2 ET1 RX2 TX2 RX1 TX1 COM -P version only PWR STATUS ON ON Flashing Flashing Flashing Flashing Flashing Off ON LED meaning Ethernet connection present Ethernet connection present Data reception on port #2 RS485/RS232 Data transmission on port #2 RS485/RS232 Data reception on port #1 RS485 Data transmission on port #1 RS485 Profinet communication active No Profinet communication The device is powered correctly INSTALLATION REGULATIONS The module has been designed for vertical installation on a DIN 46277 rail. For optimal operation and long life, adequate ventilation must be provided. Avoid positioning ducting or other objects that obstruct the ventilation slots. Avoid mounting modules over heat-generating equipment. Installation in the bottom part of the electrical panel is recommended. ATTENZIONE These devices are open type and intended for installation in an enclosure/end panel that offers mechanical protection and protection against the spread of fire. FACTORY IP ADDRESS The default module IP address is static: 192.168.90.101 PROFINET AND WEBSERVER MODE The device is normally in Profinet mode; in Profinet mode the device can be configured only through the Easy Setup2 software. In order to access the internal webserver it is necessary to put the device in Webserver mode using the Easy Setup2 or Seneca Device Discovery software. it is also possible to change the operating mode by pressing the side button PS1 following the procedure given in the user manual. WEB SERVER To access the maintenance Web Server with the factory IP address above, use the following credentials: Username: admin; Password: admin N.B.: For the Z-KEY-2ETH-P version it is first necessary to activate webserver mode CAUTION DO NOT USE DEVICES WITH THE SAME IP ADDRESS IN THE SAME ETHERNET NETWORK. MI00573-3-EN INSTALLATION MANUAL 2/4 TECHNICAL SPECIFICATIONS CERTIFICATIONS ETH 1 INSULATION ETH 2 Comm. RS485 (IDC10) Power Supply RS485/232 1500 Vac POWER SUPPLY Voltage: 11 ÷ 40Vdc; 19 ÷ 28Vac; 50 ÷ 60Hz Absorption: Max. 2W ENVIRONMENTAL Temperature: -25°C÷ + 65°C; Humidity: 30% ÷ 90% non-condensing; CONDITIONS Storage temperature: -30°C÷ + 85°C; Degree of protection: IP20 ASSEMBLY IEC EN60715, 35mm DIN rail in vertical position. CONNECTIONS 3-way removable screw terminals, pitch 5 mm RS232 or RS485 switchable on terminal COMMUNICATION Maximum Baud rate 115K, Maximum cable length RS232 < 3 m. PORTS RS485 IDC10 rear connector: Maximum Baud rate 115k. 2 Ethernet with front RJ45 connector: 100Mbit/s, maximum distance 100m SETTING THE DIP-SWITCHES WARNING The DIP-switch settings are read only at boot time. At each change, perform a restart. SW1 DIP-SWITCH: Through DIP-SWITCH-SW1 it is possible to set the IP configuration of the device: DESCRIPTION DIP 1 DIP 2 DIP 3 To obtain the configuration from the Flash memory, both SW1 DIP switch selectors must be set to OFF RESERVED To reset the device to factory settings both SW1 DIP switches must be set to ON RESERVED To force the device's IP address to the standard value of SENECA Ethernet products: 192.168.90.101 RESERVED DIP 4 RESERVED RESERVED RESERVED Reserved RESERVED RESERVED KEY ON CAUTION OFF Where present, DIP3 and DIP4 must be set to OFF. If set differently, the instrument will not work correctly. RS232/RS485 SETTING: RS232 or RS485 setting on terminals 10 -11 -12 (serial port 2) SW2 ON RS232 ACTIVATION OFF RS485 ACTIVATION MI00573-3-EN INSTALLATION MANUAL 3/4 ELECTRICAL CONNECTIONS Vac/Vdc Vac/Vdc Power supply 1 Terminals 2 and 3 can be used to provide the module with power supply as an alternative to the connection using the Z-PC-DINx bus. 2 Power voltage must be between 11 and 40Vdc (any polarity) or between 19 and 28Vac. 3 The upper limits must not be exceeded in order to avoid serious damage to the module. If the power supply source is not protected against overload, a safety fuse with a 1A max permissible value must be installed in the power supply line. GND A (+) B (-) 10 Serial port 2: RS485 SW2 = OFF The module has a serial port that can be configured with the SW2 switch. 11 If switch SW2 is in the OFF position, the RS485 COM 2 port is available at terminals 10-1112. The illustration shows how to complete connections. 12 N.B.: the indication of the RS485 connection polarity is not standardised and in some devices may be inverted. GND RX TX 10 Serial port 2: RS232 SW2 = ON The module has a serial port that can be configured with the SW2 switch. 11 If switch SW2 is in the ON position, the RS232 COM 2 port is available at terminals 10-11-12. 12 The illustration shows how to complete connections. The RS232 interface is fully settable. Power supply and Modbus interface are available using the Seneca DIN rail bus, via the IDC10 rear connector, or the Z-PC-DINAL2-17.5 accessory. RS485 GND RS485 A RS485 B Power Supply AC / + Power Supply AC / - 1 IDC 10 Back connector (IDC 10) The illustration shows the meanings of the various IDC10 connector pins if signals are to be sent via them directly. MI00573-3-EN INSTALLATION MANUAL 4/4Adobe PDF Library 17.0 Adobe InDesign 18.3 (Windows)