Paradox - Headquarters
Paradox - Headquarters
Installation Guide for PARADOX models including: PS25, PS25 Supervised Bus Power Supply, Supervised Bus Power Supply, Bus Power Supply, Power Supply, Supply
paradox.com PS25-EI02 06/2021 PS25 Supervised Bus Power Supply EVO/MG/SP Installation Manual Version 1.10 and higher Introduction The PS25 is a 2.8A supervised switching power supply that connects to the
File Info : application/pdf, 2 Pages, 302.42KB
DocumentDocumentConnect load to the three + and - terminals paralleled for your convenience. PS25 Supervised Bus Power Supply EVO/MG/SP Installation Manual Version 1.10 and higher 7 to 14Ah Rechargeable Battery Introduction The PS25 is a 2.8A supervised switching power supply that connects to the Paradox control panel's bus or may work as a standalone power supply. The PS25 provides a maximum of 2.5A (13.8VDC) continuous auxiliary power output and charge battery with 300mA. Battery charging current may increase up to 1.2A if auxiliary current is reduced accordingly. Compatibility · EVO192, EVOHD v7.14 and higher · MG5050, SP5500, SP6000, SP7000 v6.80 and higher · BabyWare v5.1 and higher · Infield v5.1 and higher Connections Connect the 4-wire (RED BLK GRN YEL) to the panel keypad bus. Please note that the RED (+) terminal is not providing power nor is it connected in any way to the PS25; it is provided for convenience only. Connect the battery (7Ah to 14Ah) and a 40VA transformer. Connect the tamper switch, no enrollment is needed, it will auto detect the tamper once the terminal is shorted and it will follow panel configuration. Note: As the battery ages, its capacity diminishes like all rechargeable components. The minimum acceptable battery capacity is 90%. Any lower value will result in a battery trouble. paradox.com Transformer: Input 110 or 230 Vac, 50 - 60 Hz Output: 16 Vac, 40 VA Note: Only one supervised power supply is supported on MG/SP panels. Box Installation Mount the PS25 in a metal box using the appropriate mounting holes, as shown below. Upgrading Firmware The PS25's firmware can be upgraded in Infield via BabyWare using a 307USB Direct Connect Interface. LED LED BUS CHARGE AUX OFF No connection to panel Not charging No power ON Panel online Battery charging Aux 10.5V - 14.0V RED: Voltage below 10.3V PS25-EI02 06/2021 Programming EVO Programming MGSP 1. Enter section [3038]. 2. Select option [7] to enable or disable Tamper supervision on the bus module. Default is disabled. 3. Enter section [3034]. Select option [5] and [6] to define Keypad/Bus Module Tamper Recognition options. Refer to the table below. Options 5 OFF OFF 6 OFF ON ON OFF ON ON Description Disabled Trouble only When armed: Follows zone types for zone tamper; generates trouble for module tamper When disarmed: Trouble only When armed: Follows zone types When disarmed: generates audible alarm 4. Enter section [4003]. 5. Enter the PS25's eight-digit module serial number. 6. Enter the three-digit module section number you wish to program. 7. Enter section [002]. The value programmed in this section represents how long the Power Supply Module will wait before reporting an AC power failure to the control panel. The trouble and trouble restore will be generated after the AC fail delay of the module. 8. Enter a three-digit decimal value (000 to 255 minutes). Default is set 30 minutes. 1. Enter section [700]. 2. Select option [7] to enable or disable Tamper supervision on the bus module. Default is disabled. 3. Enter section [705]. Select option [3] and [4] to define Keypad/Bus Module Tamper Recognition options. Refer to the table below. Options 3 OFF 4 OFF OFF ON ON OFF ON ON Description Disabled Trouble only When armed: Audible alarm When disarmed: Trouble only Audible alarm 4. Enter section [839]. The value programmed in this section represents how long the Power Supply Module will wait before reporting an AC power failure. 5. Enter a three-digit decimal value (000 to 255 minutes). Default is set 30 minutes. Technical Specifications AC Power Input* Auxiliary Power Output Power Consumption (without load) Type of Power Supply Battery Low Battery Charging Operating Temperature 100 Vac 0.4A or 230 Vac 0.2A, 50 - 60 Hz 13.8 Vdc ±5% when AC present 12.8 Vdc when on battery 2.5A max 117 mA at 16.5 Vac Type A 12 Vdc, 7 Ah to 14 Ah 10.7 Vdc, battery disconnect at 9.5V 300 mA min to 1200 mA (redirect from auxiliary if less than 2.5A) -20 to +50 C Humidity 95% maximum Bus Supervision AC, Aux voltage, Battery Dimensions (H x W x D) 5.6 x 14 x 2.5 cm (2.2 x 5.5 x 0.9 in.) and Weight 0.1 kg (0.2 lbs.) EN 50131-1, EN 50131-6, Grade 2 Class II Certifications Certification Body: Applica Test and Certification * When AC power is disconnected and the power supply is operating on battery, the Auxiliary Output is 12.8V ±16% Warranty For complete warranty information on this product, please refer to the Limited Warranty Statement is found on the website: www.paradox.com/terms or contact your local distributor. Specifications may change without prior notice. Patents US, Canadian and international patents may apply. Paradox is a trademark or registered trademark of Paradox Security Systems (Bahamas) Ltd. paradox.com PS25-EI02 06/2021