Q1 Cell Phone Holder with Wireless Speaker and Clock

Product Features

• Integrated phone stand for hands-free use.
• Wireless speakerphone functionality for conference calls.
• Built-in LED digital clock.
• Integrated lithium battery for portability.

What's Included

• Q1 Main Unit ?
• Stretch bracket ?
• USB Charging Cable ?
• User Manual ?

Details about Buttons and Device Layout

The device features a phone stand, speaker, and LED display screen.

Top View: Contains controls labeled "Power/12h-24h", "Light/Dimmer", and a "Mic" (microphone).
Bottom View: Features the "Type-C (DC IN 5V)" charging port.
Right Side View: Includes buttons for "Previous track/Vol-", "Next track/Vol+", and "Play/Pause/Answer the phone".

Before using this multi-function device, please read the instructions carefully and operate in strict accordance with them.

Getting Started

1. Open the package, remove the product, and unfold the mobile phone support frame.
2. Long press the POWER button to turn on the speaker. The LED screen will light up simultaneously.
3. Wireless Connection and Playback:

   Long press the POWER button to turn on the speaker. The LED screen will light up, and the BT symbol will flash. On your mobile phone, search for the wireless device named "Q1" and connect. The speaker will provide a voice prompt upon successful connection. Once connected, turn on your phone's music player to play music through the speaker's wireless signal.

   Note: If no operation is performed for 20 minutes after connecting wirelessly, the connection will automatically disconnect and require a restart to reconnect.

4. Playing Music:

   During music playback, press ⬅️ for the previous song, ➡️ for the next song, and ▶️ for play/pause. Long press ⬅️ to decrease volume and long press ➡️ to increase volume.

5. Press the Play/Pause button once to answer an incoming call ?.
6. Long press the Light/Dimmer button to turn the ambient light ? on or off (located near the speaker).

Time and Settings

7. Time Setting:

   When the phone is wirelessly connected to the speaker, the time will automatically synchronize from the phone and be displayed on the LED screen.

8. 12H/24H Setting:

   Long press the 12H/24H button to switch between 12-hour and 24-hour modes. In 12-hour mode, the LED screen will display AM or PM symbols.

Battery Charging

When the battery is low during use, the speaker will emit a beeping low voltage prompt, and the ⚠️ icon will flash. Charge the speaker promptly to avoid automatic shutdown.

Using the Mobile Phone Holder

Install the long arm bracket by threading it onto the base. This allows you to securely place your phone on the bracket for use.

[Threading action to tighten or loosen bracket]

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.